From: Michal Suchanek <hramrach@gmail.com>
To: Mark Brown <broonie@kernel.org>
Cc: Julian Calaby <julian.calaby@gmail.com>,
linux-sunxi <linux-sunxi@googlegroups.com>,
Maxime Ripard <maxime.ripard@free-electrons.com>,
Chen-Yu Tsai <wens@csie.org>,
linux-spi <linux-spi@vger.kernel.org>,
"Mailing List, Arm" <linux-arm-kernel@lists.infradead.org>,
"linux-kernel@vger.kernel.org" <linux-kernel@vger.kernel.org>
Subject: Re: [linux-sunxi] [PATCH 1/5] spi: sunxi: fix transfer timeout
Date: Tue, 31 May 2016 13:52:20 +0200 [thread overview]
Message-ID: <CAOMqctQqJaKBA++yiniroEcTjWCMD5WT7CpVjTYBmLzGcB2vYw@mail.gmail.com> (raw)
In-Reply-To: <20160530112350.GI29837@sirena.org.uk>
Hello
On 30 May 2016 at 13:23, Mark Brown <broonie@kernel.org> wrote:
> On Fri, May 27, 2016 at 03:10:11PM +1000, Julian Calaby wrote:
>> On Fri, May 27, 2016 at 3:05 PM, Michal Suchanek <hramrach@gmail.com> wrote:
>
>> >> Also, should the changes for the drivers be in two separate patches also?
>
>> > That's basically the same driver with different constants so I guess not.
>
>> Fair enough, I withdraw my comment then.
>
> If it's the same driver with different constants it should really
> actually be the same driver - I did ask this when the drivers were
> originally merged...
There are some slight differences and the constants really are
different for each driver.
You would need a register remap adaptation layer and a few qirks for
each revision of the driver.
It's certainly possible to merge them but I am not sure if that gives
easier to maintain code.
On the other hand, comparing the drivers there is different comment
anout clock calculation arithmetic and the code is the same :S
Thanks
Michal
--- spi-sun4i.c 2016-05-31 13:19:27.076510421 +0200
+++ spi-sun6i.c 2016-05-31 13:26:58.123580382 +0200
@@ -19,65 +19,72 @@
#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/pm_runtime.h>
+#include <linux/reset.h>
#include <linux/spi/spi.h>
-#define SUNXI_FIFO_DEPTH 64
+#define SUNXI_FIFO_DEPTH 128
-#define SUNXI_RXDATA_REG 0x00
+#define SUNXI_TXDATA_REG 0x200
-#define SUNXI_TXDATA_REG 0x04
+#define SUNXI_RXDATA_REG 0x300
#define SUNXI_TFR_CTL_REG 0x08
-#define SUNXI_TFR_CTL_ENABLE BIT(0)
-#define SUNXI_TFR_CTL_MASTER BIT(1)
-#define SUNXI_TFR_CTL_CPHA BIT(2)
-#define SUNXI_TFR_CTL_CPOL BIT(3)
-#define SUNXI_TFR_CTL_CS_ACTIVE_LOW BIT(4)
-#define SUNXI_TFR_CTL_LMTF BIT(6)
-#define SUNXI_TFR_CTL_TF_RST BIT(8)
-#define SUNXI_TFR_CTL_RF_RST BIT(9)
-#define SUNXI_TFR_CTL_XCH BIT(10)
-#define SUNXI_TFR_CTL_CS_MASK 0x3000
-#define SUNXI_TFR_CTL_CS(cs) (((cs) << 12) & SUNXI_TFR_CTL_CS_MASK)
-#define SUNXI_TFR_CTL_DHB BIT(15)
-#define SUNXI_TFR_CTL_CS_MANUAL BIT(16)
-#define SUNXI_TFR_CTL_CS_LEVEL BIT(17)
-#define SUNXI_TFR_CTL_TP BIT(18)
+#define SUNXI_TFR_CTL_CPHA BIT(0)
+#define SUNXI_TFR_CTL_CPOL BIT(1)
+#define SUNXI_TFR_CTL_SPOL BIT(2)
+#define SUNXI_TFR_CTL_CS_MASK 0x30
+#define SUNXI_TFR_CTL_CS(cs) (((cs) << 4) & SUNXI_TFR_CTL_CS_MASK)
+#define SUNXI_TFR_CTL_CS_MANUAL BIT(6)
+#define SUNXI_TFR_CTL_CS_LEVEL BIT(7)
+#define SUNXI_TFR_CTL_DHB BIT(8)
+#define SUNXI_TFR_CTL_FBS BIT(12)
+#define SUNXI_TFR_CTL_XCH BIT(31)
-#define SUNXI_INT_CTL_REG 0x0c
-#define SUNXI_INT_CTL_TC BIT(16)
+#define SUNXI_INT_CTL_REG 0x10
+#define SUNXI_INT_CTL_RF_OVF BIT(8)
+#define SUNXI_INT_CTL_TC BIT(12)
-#define SUNXI_INT_STA_REG 0x10
+#define SUNXI_INT_STA_REG 0x14
-#define SUNXI_DMA_CTL_REG 0x14
+#define SUNXI_FIFO_CTL_REG 0x18
+#define SUNXI_FIFO_CTL_RF_RST BIT(15)
+#define SUNXI_FIFO_CTL_TF_RST BIT(31)
-#define SUNXI_CLK_CTL_REG 0x1c
+#define SUNXI_CLK_CTL_REG 0x24
#define SUNXI_CLK_CTL_CDR2_MASK 0xff
#define SUNXI_CLK_CTL_CDR2(div) (((div) &
SUNXI_CLK_CTL_CDR2_MASK) << 0)
#define SUNXI_CLK_CTL_CDR1_MASK 0xf
#define SUNXI_CLK_CTL_CDR1(div) (((div) &
SUNXI_CLK_CTL_CDR1_MASK) << 8)
#define SUNXI_CLK_CTL_DRS BIT(12)
-#define SUNXI_BURST_CNT_REG 0x20
+#define SUNXI_BURST_CNT_REG 0x30
#define SUNXI_BURST_CNT(cnt) ((cnt) & 0xffffff)
-#define SUNXI_XMIT_CNT_REG 0x24
+#define SUNXI_XMIT_CNT_REG 0x34
#define SUNXI_XMIT_CNT(cnt) ((cnt) & 0xffffff)
-#define SUNXI_FIFO_STA_REG 0x28
+#define SUNXI_FIFO_STA_REG 0x1c
#define SUNXI_FIFO_STA_RF_CNT_MASK 0x7f
#define SUNXI_FIFO_STA_RF_CNT_BITS 0
#define SUNXI_FIFO_STA_TF_CNT_MASK 0x7f
#define SUNXI_FIFO_STA_TF_CNT_BITS 16
-#define SUNXI_WAIT_REG 0x18
+#define SUNXI_BURST_CTL_CNT_REG 0x38
+#define SUNXI_BURST_CTL_CNT_STC(cnt) ((cnt) & 0xffffff)
+
+#define SUNXI_GBL_CTL_REG 0x04
+#define SUNXI_GBL_CTL_BUS_ENABLE BIT(0)
+#define SUNXI_GBL_CTL_MASTER BIT(1)
+#define SUNXI_GBL_CTL_TP BIT(7)
+#define SUNXI_GBL_CTL_RST BIT(31)
struct sunxi_spi {
struct spi_master *master;
void __iomem *base_addr;
struct clk *hclk;
struct clk *mclk;
+ struct reset_control *rstc;
struct completion done;
@@ -136,37 +143,18 @@
u32 reg;
reg = sunxi_spi_read(sspi, SUNXI_TFR_CTL_REG);
-
reg &= ~SUNXI_TFR_CTL_CS_MASK;
reg |= SUNXI_TFR_CTL_CS(spi->chip_select);
- /* We want to control the chip select manually */
- reg |= SUNXI_TFR_CTL_CS_MANUAL;
-
if (enable)
reg |= SUNXI_TFR_CTL_CS_LEVEL;
else
reg &= ~SUNXI_TFR_CTL_CS_LEVEL;
- /*
- * Even though this looks irrelevant since we are supposed to
- * be controlling the chip select manually, this bit also
- * controls the levels of the chip select for inactive
- * devices.
- *
- * If we don't set it, the chip select level will go low by
- * default when the device is idle, which is not really
- * expected in the common case where the chip select is active
- * low.
- */
- if (spi->mode & SPI_CS_HIGH)
- reg &= ~SUNXI_TFR_CTL_CS_ACTIVE_LOW;
- else
- reg |= SUNXI_TFR_CTL_CS_ACTIVE_LOW;
-
sunxi_spi_write(sspi, SUNXI_TFR_CTL_REG, reg);
}
+
static int sunxi_spi_transfer_one(struct spi_master *master,
struct spi_device *spi,
struct spi_transfer *tfr)
@@ -189,17 +177,16 @@
/* Clear pending interrupts */
sunxi_spi_write(sspi, SUNXI_INT_STA_REG, ~0);
-
- reg = sunxi_spi_read(sspi, SUNXI_TFR_CTL_REG);
-
/* Reset FIFOs */
- sunxi_spi_write(sspi, SUNXI_TFR_CTL_REG,
- reg | SUNXI_TFR_CTL_RF_RST | SUNXI_TFR_CTL_TF_RST);
+ sunxi_spi_write(sspi, SUNXI_FIFO_CTL_REG,
+ SUNXI_FIFO_CTL_RF_RST | SUNXI_FIFO_CTL_TF_RST);
/*
* Setup the transfer control register: Chip Select,
* polarities, etc.
*/
+ reg = sunxi_spi_read(sspi, SUNXI_TFR_CTL_REG);
+
if (spi->mode & SPI_CPOL)
reg |= SUNXI_TFR_CTL_CPOL;
else
@@ -211,10 +198,9 @@
reg &= ~SUNXI_TFR_CTL_CPHA;
if (spi->mode & SPI_LSB_FIRST)
- reg |= SUNXI_TFR_CTL_LMTF;
+ reg |= SUNXI_TFR_CTL_FBS;
else
- reg &= ~SUNXI_TFR_CTL_LMTF;
-
+ reg &= ~SUNXI_TFR_CTL_FBS;
/*
* If it's a TX only transfer, we don't want to fill the RX
@@ -225,6 +211,9 @@
else
reg |= SUNXI_TFR_CTL_DHB;
+ /* We want to control the chip select manually */
+ reg |= SUNXI_TFR_CTL_CS_MANUAL;
+
sunxi_spi_write(sspi, SUNXI_TFR_CTL_REG, reg);
/* Ensure that we have a parent clock fast enough */
@@ -239,7 +228,7 @@
*
* We have two choices there. Either we can use the clock
* divide rate 1, which is calculated thanks to this formula:
- * SPI_CLK = MOD_CLK / (2 ^ (cdr + 1))
+ * SPI_CLK = MOD_CLK / (2 ^ cdr)
* Or we can use CDR2, which is calculated with the formula:
* SPI_CLK = MOD_CLK / (2 * (cdr + 1))
* Wether we use the former or the latter is set through the
@@ -268,6 +257,8 @@
/* Setup the counters */
sunxi_spi_write(sspi, SUNXI_BURST_CNT_REG, SUNXI_BURST_CNT(tfr->len));
sunxi_spi_write(sspi, SUNXI_XMIT_CNT_REG, SUNXI_XMIT_CNT(tx_len));
+ sunxi_spi_write(sspi, SUNXI_BURST_CTL_CNT_REG,
+ SUNXI_BURST_CTL_CNT_STC(tx_len));
/* Fill the TX FIFO */
sunxi_spi_fill_fifo(sspi, SUNXI_FIFO_DEPTH);
@@ -327,11 +318,19 @@
goto err;
}
- sunxi_spi_write(sspi, SUNXI_TFR_CTL_REG,
- SUNXI_TFR_CTL_ENABLE | SUNXI_TFR_CTL_MASTER | SUNXI_TFR_CTL_TP);
+ ret = reset_control_deassert(sspi->rstc);
+ if (ret) {
+ dev_err(dev, "Couldn't deassert the device from reset\n");
+ goto err2;
+ }
+
+ sunxi_spi_write(sspi, SUNXI_GBL_CTL_REG,
+ SUNXI_GBL_CTL_BUS_ENABLE | SUNXI_GBL_CTL_MASTER |
SUNXI_GBL_CTL_TP);
return 0;
+err2:
+ clk_disable_unprepare(sspi->mclk);
err:
clk_disable_unprepare(sspi->hclk);
out:
@@ -343,6 +342,7 @@
struct spi_master *master = dev_get_drvdata(dev);
struct sunxi_spi *sspi = spi_master_get_devdata(master);
+ reset_control_assert(sspi->rstc);
clk_disable_unprepare(sspi->mclk);
clk_disable_unprepare(sspi->hclk);
@@ -411,6 +411,13 @@
init_completion(&sspi->done);
+ sspi->rstc = devm_reset_control_get(&pdev->dev, NULL);
+ if (IS_ERR(sspi->rstc)) {
+ dev_err(&pdev->dev, "Couldn't get reset controller\n");
+ ret = PTR_ERR(sspi->rstc);
+ goto err_free_master;
+ }
+
/*
* This wake-up/shutdown pattern is to be able to have the
* device woken up, even if runtime_pm is disabled
@@ -449,7 +456,7 @@
}
static const struct of_device_id sunxi_spi_match[] = {
- { .compatible = "allwinner,sun4i-a10-spi", },
+ { .compatible = "allwinner,sun6i-a31-spi", },
{}
};
MODULE_DEVICE_TABLE(of, sunxi_spi_match);
@@ -472,5 +479,5 @@
MODULE_AUTHOR("Pan Nan <pannan@allwinnertech.com>");
MODULE_AUTHOR("Maxime Ripard <maxime.ripard@free-electrons.com>");
-MODULE_DESCRIPTION("Allwinner A1X/A20 SPI controller driver");
+MODULE_DESCRIPTION("Allwinner A31 SPI controller driver");
MODULE_LICENSE("GPL");
next prev parent reply other threads:[~2016-05-31 11:53 UTC|newest]
Thread overview: 28+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <cover.1464130597.git.hramrach@gmail.com>
[not found] ` <e315008b5e9dc3f1490507508fd2f6e94767dfbb.1464130597.git.hramrach@gmail.com>
2016-05-30 8:37 ` [PATCH 2/5] spi: sun4i: fix FIFO limit Maxime Ripard
[not found] ` <5fffb7eca6f4b70853d92be2403595d6d06bede7.1464130597.git.hramrach@gmail.com>
2016-05-30 8:37 ` [PATCH 3/5] spi: sunxi: expose maximum transfer size limit Maxime Ripard
2016-05-30 8:57 ` Michal Suchanek
2016-06-01 18:14 ` Maxime Ripard
[not found] ` <7292b1fa08de4f453a643beb63e9faa7826726f6.1464130597.git.hramrach@gmail.com>
2016-05-30 9:17 ` [PATCH 4/5] spi: sunxi: set maximum and minimum speed of SPI master Maxime Ripard
[not found] ` <cb90b922caa6ac07c1425d726ea19709ee5284f4.1464130597.git.hramrach@gmail.com>
2016-05-27 2:05 ` [linux-sunxi] [PATCH 1/5] spi: sunxi: fix transfer timeout Julian Calaby
2016-05-27 5:05 ` Michal Suchanek
2016-05-27 5:10 ` Julian Calaby
2016-05-30 11:23 ` Mark Brown
2016-05-31 11:52 ` Michal Suchanek [this message]
2016-06-01 18:20 ` Maxime Ripard
2016-05-30 9:44 ` Maxime Ripard
[not found] ` <ba0d6eb37cc4b0d2c46acbf9fcd7d644b3545ce8.1464130597.git.hramrach@gmail.com>
2016-05-30 11:26 ` [PATCH 5/5] RFC spi: sun4i: add DMA support Mark Brown
2016-05-30 12:11 ` Geert Uytterhoeven
2016-05-30 15:03 ` Mark Brown
2016-05-30 15:28 ` Michal Suchanek
2016-05-30 15:50 ` Mark Brown
2016-05-31 10:44 ` Michal Suchanek
2016-05-31 13:27 ` Mark Brown
2016-05-31 14:19 ` Michal Suchanek
2016-06-02 8:18 ` Maxime Ripard
2016-06-01 18:00 ` Maxime Ripard
2016-06-02 4:42 ` [linux-sunxi] " Priit Laes
2016-06-02 9:18 ` Mark Brown
2016-06-02 12:14 ` Michal Suchanek
2016-06-02 14:26 ` Mark Brown
2016-06-05 11:27 ` Michal Suchanek
2016-06-06 11:36 ` Mark Brown
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=CAOMqctQqJaKBA++yiniroEcTjWCMD5WT7CpVjTYBmLzGcB2vYw@mail.gmail.com \
--to=hramrach@gmail.com \
--cc=broonie@kernel.org \
--cc=julian.calaby@gmail.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-spi@vger.kernel.org \
--cc=linux-sunxi@googlegroups.com \
--cc=maxime.ripard@free-electrons.com \
--cc=wens@csie.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®