Re: [PATCH 02/10] dt-bindings: pinctrl: Add devicetree bindings for DM816x SoC Pinctrl

["Ettore Chimenti" <ettore.chimenti@linaro.org>]

Hi Krzyszrof,

On Mon Oct 19, 2026 at 8:46 AM CEST, Krzysztof Kozlowski wrote:
> On 16/10/2026 17:07, Ettore Chimenti wrote:
>> Hi Krzyszrof,
>> 
>> On Fri Oct 16, 2026 at 4:51 PM CEST, Krzysztof Kozlowski wrote:
>>> On 16/10/2026 16:41, Ettore Chimenti wrote:
>>>> Add devicetree bindings for TI DM816x SoC pinctrl configuration.
>>>> Using same definition as OMAP2/3 except pullup/down enable macros, which
>>>> are inverted in this SoC.
>>>>
>>>> Signed-off-by: Ettore Chimenti <ettore.chimenti@linaro.org>
>>>> ---
>>>>  include/dt-bindings/pinctrl/dm816x.h | 20 ++++++++++++++++++++
>>>>  1 file changed, 20 insertions(+)
>>>>
>>>> diff --git a/include/dt-bindings/pinctrl/dm816x.h b/include/dt-bindings/pinctrl/dm816x.h
>>>> new file mode 100644
>>>> index 000000000000..15aa15bca9bd
>>>> --- /dev/null
>>>> +++ b/include/dt-bindings/pinctrl/dm816x.h
>>>> @@ -0,0 +1,20 @@
>>>> +/* SPDX-License-Identifier: GPL-2.0-only */
>>>> +/*
>>>> + * This header provides constants specific to DM816X pinctrl bindings.
>>>> + */
>>>> +
>>>> +#ifndef _DT_BINDINGS_PINCTRL_DM816X_H
>>>> +#define _DT_BINDINGS_PINCTRL_DM816X_H
>>>> +
>>>> +#include <dt-bindings/pinctrl/omap.h>
>>>
>>> I do not see this being used here, IWYU.
>>>
>>>> +
>>>> +#undef PULL_UP
>>>> +#undef PULL_ENA
>>>
>>> Why are you undefining other macros? That's not a easy to follow code.
>> 
>> Do you prefer to duplicate `omap.h` defines? Only the defines above do not
>> apply to DM816x.
>
> Not sure what you need to duplicate, but if you add header with bindings
> for this device, then you should not include headers for other devices.

I basically used dm814x.h as a template which does that, is that not
correct?

>
>> 
>>>
>>>
>>>> +
>>>> +/* DM81xx mux bit defines */
>>>> +#define PULL_ENA		(0 << 3)  /* Pullup enabled  => 0 */
>>>> +#define PULL_DIS		(1 << 3)  /* Pullup disabled => 1 */
>>>> +#define PULL_DN			(0 << 4)
>>>> +#define PULL_UP			(1 << 4)
>>>
>>> I do not see this used by drivers, so why do we need one more header?
>>> What part of SW are you binding here?
>>>
>> 
>> I added those (DN/UP) because they are not defined in `omap.h`. It may be
>> convenient for future board upstreaming. I can drop those if undesired.
>
> Just add the header to proper place - DTS. These are just not looking as
> bindings.

Sorry, does dm814x.h not look as bindings? I'm a bit confused.
FWIW, dm8148-evm.dts is not including the header, dm814x.dtsi is.
Following 

Basically PULL_ENA define in omap.h is wrong for DM8168 SoCs. 

For a better solution, you would prefer:
- Keep omap.h in dm816x.dtsi
- Add a variant like DM816X_PULL_{ENA,DIS} in dm816x.h
- Replace defines in dm8168-evm.dts
- Add the header in dm8168-evm.dts

or:

- Keep omap.h in dm816x.dtsi
- Add a variant like DM816X_PULL_{ENA,DIS} in omap.h
- Replace defines in dm8168-evm.dts

Thanks for your review, 
Ettore

>
> Best regards,
> Krzysztof