I'm sure this isn't the address to send this to, but I
don't know where to send this.

I just upgraded from 2.4.0-test12 to 2.4.0, and I got a
kernel panac after about 6 hours.  Then updated to 2.4.0-ac4
and got a massive amount of scsi errors.  The server was again
up for about 6 hours.  This was in the syslog:

-----------------------------------------------------------------
Jan  8 16:51:34 kenny kernel: (scsi0:-1:-1:-1) Referenced SCB 12 not valid
during SELTO.
Jan  8 16:51:34 kenny kernel:         SCSISEQ = 0x5a SEQADDR = 0x8 SSTAT0 =
0x10 SSTAT1 = 0x88
Jan  8 16:51:34 kenny kernel: (scsi0:-1:-1:-1) Referenced SCB 12 not valid
during SELTO.
Jan  8 16:51:34 kenny kernel:         SCSISEQ = 0x5a SEQADDR = 0x8 SSTAT0 =
0x10 SSTAT1 = 0x88
Jan  8 16:51:34 kenny kernel: (scsi0:-1:-1:-1) Referenced SCB 12 not valid
during SELTO.
Jan  8 16:51:34 kenny kernel:         SCSISEQ = 0x5a SEQADDR = 0x8 SSTAT0 =
0x10 SSTAT1 = 0x88
Jan  8 16:51:34 kenny kernel: (scsi0:-1:-1:-1) Referenced SCB 12 not valid
during SELTO.
Jan  8 16:51:34 kenny kernel:         SCSISEQ = 0x5a SEQADDR = 0x8 SSTAT0 =
0x10 SSTAT1 = 0x88
Jan  8 16:51:34 kenny kernel: (scsi0:0:1:0) Synchronous at 80.0 Mbyte/sec,
offset 63.
Jan  8 16:51:34 kenny kernel: (scsi0:0:3:0) Synchronous at 80.0 Mbyte/sec,
offset 63.
Jan  8 16:51:56 kenny kernel: SCSI host 0 abort (pid 0) timed out -
resetting
Jan  8 16:51:56 kenny kernel: SCSI bus is being reset for host 0 channel 0.
Jan  8 16:51:57 kenny kernel: SCSI host 0 channel 0 reset (pid 0) timed
out - trying harder
Jan  8 16:51:57 kenny kernel: SCSI bus is being reset for host 0 channel 0.
Jan  8 16:51:57 kenny kernel: SCSI host 0 reset (pid 0) timed out again -
Jan  8 16:51:57 kenny kernel: probably an unrecoverable SCSI bus or device
hang.
Jan  8 16:52:04 kenny kernel: scsi : aborting command due to timeout : pid
0, scsi0, channel 0, id 2, lun 0 0x2a 00 00
 1b 00 5c 00 00 08 00
Jan  8 16:52:04 kenny kernel: scsi : aborting command due to timeout : pid
0, scsi0, channel 0, id 2, lun 0 0x2a 00 00
 1b 00 68 00 00 08 00
Jan  8 16:52:04 kenny kernel: scsi : aborting command due to timeout : pid
0, scsi0, channel 0, id 2, lun 0 0x2a 00 00
 1b 00 84 00 00 04 00
----------------------------------------------------------------------

The server board is an Intel STL2, with one P3-800.  I will atach my current
dmesg.
Thanks for any help

Dave Joyce
ProbeTalk.com server admin