Re: [PATCH v2 3/3] media: pci: intel: ivsc: Add acquire/release API for ivsc

[Laurent Pinchart <laurent.pinchart@ideasonboard.com>]

Hi Wentong,

On Fri, Feb 17, 2023 at 06:10:22AM +0000, Wu, Wentong wrote:
> On Sent: Wednesday, February 15, 2023 5:46 PM, Laurent Pinchart wrote:
> > On Wed, Feb 15, 2023 at 10:03:29AM +0100, Hans de Goede wrote:
> > > On 2/14/23 17:06, Sakari Ailus wrote:
> > > > On Mon, Feb 13, 2023 at 10:23:47AM +0800, Wentong Wu wrote:
> > > >> IVSC directly connects to camera sensor on source side, and on
> > > >> output side it not only connects ISH via I2C, but also exposes MIPI
> > > >> CSI-2 interface to output camera sensor data. IVSC can use the
> > > >> camera sensor data to do AI algorithm, and send the results to ISH.
> > > >> On the other end, IVSC can share camera sensor to host by routing
> > > >> the raw camera sensor data to the exposed MIPI CSI-2 interface. But
> > > >> they can not work at the same time, so software APIs are defined to
> > > >> sync the ownership.
> > > >>
> > > >> This commit defines the interfaces between IVSC and camera sensor
> > > >> driver in include/linux/ivsc.h. The camera driver controls
> > > >> ownership of the CSI-2 link and sensor with the acquire/release
> > > >> APIs. When acquiring camera, lane number and link freq are also
> > > >> required by IVSC frame router.
> > > >
> > > > The more I learn about this system, the more I'm inclined to think
> > > > this functionality should be exposed as a V4L2 sub-device. IVSC
> > > > doesn't really do anything to the data (as long as it directs it
> > > > towards the CSI-2 receiver in the SoC), but it is definitely
> > > > part of the image pipeline.
> > >
> > > Yes I happened to discuss this exact same thing with Laurent at FOSDEM
> > > and we also came to the conclusion that the IVSC chip should be
> > > modeled as a V4L2 sub-device.
> > 
> > Agreed.
> 
> Thanks for your quick review and conclusion, I'm fresh to media
> sub-system, is there any convention that I should follow to upstream
> this kind of v4l2 sub-device driver so that not too much back and
> forth?

This is a tentative proposal, as I'm not very familiar with the hardware
architecture:

- The subdev should have two pads, a sink pad connected to the camera
  sensor, and a source pad connected to the CSI-2 receiver in the IPU.

- As for any new driver, the subdev driver should use the active state
  managed by the v4l2-subdev core. This requires calling
  v4l2_subdev_init_finalize() at probe time. See
  https://git.linuxtv.org/media_tree.git/commit/?id=a2514b9a634a for an
  example of a subdev driver converted to this mechanism.

- As we're talking about CSI-2, the subdev driver should use the streams
  API that was recently merged, and in particular support the
  .get_frame_desc(), .set_routing(), .enable_streams() and
  .disable_streams() operations.

- I don't see a need to support V4L2 controls in the subdev driver, but
  I may be missing something.

- The driver should be validated with v4l2-compliance, part of
  v4l-utils.

> > > > I suppose the intended use cases assume a single instance of IVSC
> > > > (as well as MEI) but there can, and often are, be multiple camera
> > > > sensors in the system. The decision whether to request pass-through
> > > > from IVCS can't be done in the camera sensor driver, and should not
> > > > be visible to the camera sensor driver. Exposing IVSC as a V4L2
> > > > sub-device makes this trivial to address, as the IVSC driver's V4L2
> > > > sub-device video s_stream() operation gets called before streaming is started.
> > > >
> > > > The information whether IVSC is found between the camera sensor and
> > > > the host's CSI-2 receiver (IPU in this case) should come from system
> > > > firmware and accessed most probably by what is called cio2-bridge at
> > > > the moment.
> > > >
> > > > The privacy status can be a V4L2 control.
> > > >
> > > > Also cc Hans.
> > > >
> > > >> Signed-off-by: Wentong Wu <wentong.wu@intel.com>
> > > >> ---
> > > >>  drivers/media/pci/intel/ivsc/Makefile |  1 +
> > > >>  drivers/media/pci/intel/ivsc/ivsc.c   | 84 +++++++++++++++++++++++++++
> > > >>  include/linux/ivsc.h                  | 55 ++++++++++++++++++
> > > >>  3 files changed, 140 insertions(+)  create mode 100644
> > > >> drivers/media/pci/intel/ivsc/ivsc.c

[snip]

-- 
Regards,

Laurent Pinchart