On Tue, Mar 28, 2023 at 02:40:33PM +0200, Takashi Iwai wrote:
> Hi,
> 
> we've got a regression report for e1000e device on Lenovo T460p since
> 6.2 kernel (with openSUSE Tumbleweed).  The details are found in
>   https://bugzilla.opensuse.org/show_bug.cgi?id=1209254
> 
> It seems that the driver can't detect the 1000Mbps but only 10/100Mbps
> link, eventually making the device unusable.
> 
> On 6.1.12:
> [    5.119117] e1000e: Intel(R) PRO/1000 Network Driver
> [    5.119120] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
> [    5.121754] e1000e 0000:00:1f.6: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
> [    7.905526] e1000e 0000:00:1f.6 0000:00:1f.6 (uninitialized): Failed to disable ULP
> [    7.988925] e1000e 0000:00:1f.6 0000:00:1f.6 (uninitialized): registered PHC clock
> [    8.069935] e1000e 0000:00:1f.6 eth0: (PCI Express:2.5GT/s:Width x1) 50:7b:9d:cf:13:43
> [    8.069942] e1000e 0000:00:1f.6 eth0: Intel(R) PRO/1000 Network Connection
> [    8.072691] e1000e 0000:00:1f.6 eth0: MAC: 12, PHY: 12, PBA No: 1000FF-0FF
> [   11.643919] e1000e 0000:00:1f.6 eth0: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
> [   15.437437] e1000e 0000:00:1f.6 eth0: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
> 
> On 6.2.4:
> [    4.344140] e1000e: Intel(R) PRO/1000 Network Driver
> [    4.344143] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
> [    4.344933] e1000e 0000:00:1f.6: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
> [    7.113334] e1000e 0000:00:1f.6 0000:00:1f.6 (uninitialized): Failed to disable ULP
> [    7.201715] e1000e 0000:00:1f.6 0000:00:1f.6 (uninitialized): registered PHC clock
> [    7.284038] e1000e 0000:00:1f.6 eth0: (PCI Express:2.5GT/s:Width x1) 50:7b:9d:cf:13:43
> [    7.284044] e1000e 0000:00:1f.6 eth0: Intel(R) PRO/1000 Network Connection
> [    7.284125] e1000e 0000:00:1f.6 eth0: MAC: 12, PHY: 12, PBA No: 1000FF-0FF
> [   10.897973] e1000e 0000:00:1f.6 eth0: NIC Link is Up 10 Mbps Full Duplex, Flow Control: None
> [   10.897977] e1000e 0000:00:1f.6 eth0: 10/100 speed: disabling TSO
> [   14.710059] e1000e 0000:00:1f.6 eth0: NIC Link is Up 10 Mbps Full Duplex, Flow Control: None
> [   14.710064] e1000e 0000:00:1f.6 eth0: 10/100 speed: disabling TSO
> [   59.894807] e1000e 0000:00:1f.6 eth0: NIC Link is Up 10 Mbps Full Duplex, Flow Control: None
> [   59.894812] e1000e 0000:00:1f.6 eth0: 10/100 speed: disabling TSO
> [   63.808662] e1000e 0000:00:1f.6 eth0: NIC Link is Up 10 Mbps Full Duplex, Flow Control: None
> [   63.808668] e1000e 0000:00:1f.6 eth0: 10/100 speed: disabling TSO
> 
> The same problem persists with 6.3-rc3.
> 

I'm adding this to regzbot:

#regzbot ^introduced: v6.1.12..v6.2.4
#regzbot: e1000 probe/link detection fails since v6.2

Thanks.

-- 
An old man doll... just what I always wanted! - Clara