Re: [EXTERNAL] Re: [net-next PATCH v10 03/11] octeontx2-pf: Create representor netdev

[Jiri Pirko <jiri@resnulli.us>]

Fri, Aug 16, 2024 at 03:36:12PM CEST, gakula@marvell.com wrote:
>
>
>>-----Original Message-----
>>From: Jiri Pirko <jiri@resnulli.us>
>>Sent: Thursday, August 8, 2024 9:22 PM
>>To: Geethasowjanya Akula <gakula@marvell.com>
>>Cc: netdev@vger.kernel.org; linux-kernel@vger.kernel.org; kuba@kernel.org;
>>davem@davemloft.net; pabeni@redhat.com; edumazet@google.com; Sunil
>>Kovvuri Goutham <sgoutham@marvell.com>; Subbaraya Sundeep Bhatta
>><sbhatta@marvell.com>; Hariprasad Kelam <hkelam@marvell.com>
>>Subject: [EXTERNAL] Re: [net-next PATCH v10 03/11] octeontx2-pf: Create
>>representor netdev
>>
>>Mon, Aug 05, 2024 at 03:18:07PM CEST, gakula@marvell.com wrote:
>>>Adds initial devlink support to set/get the switchdev mode.
>>>Representor netdevs are created for each rvu devices when the switch
>>>mode is set to 'switchdev'. These netdevs are be used to control and
>>>configure VFs.
>>>
>>>Signed-off-by: Geetha sowjanya <gakula@marvell.com>
>>>Reviewed-by: Simon Horman <horms@kernel.org>
>>>---
>>> .../ethernet/marvell/octeontx2.rst            |  85 +++++++++
>>> .../marvell/octeontx2/nic/otx2_devlink.c      |  49 ++++++
>>> .../net/ethernet/marvell/octeontx2/nic/rep.c  | 165 ++++++++++++++++++
>>> .../net/ethernet/marvell/octeontx2/nic/rep.h  |   3 +
>>> 4 files changed, 302 insertions(+)
>>>
>>>diff --git
>>>a/Documentation/networking/device_drivers/ethernet/marvell/octeontx2.rs
>>>t
>>>b/Documentation/networking/device_drivers/ethernet/marvell/octeontx2.rs
>>>t index 1e196cb9ce25..4eb4e6788ffc 100644
>>>---
>>>a/Documentation/networking/device_drivers/ethernet/marvell/octeontx2.rs
>>>t
>>>+++ b/Documentation/networking/device_drivers/ethernet/marvell/octeontx
>>>+++ 2.rst
>>>@@ -14,6 +14,7 @@ Contents
>>> - `Basic packet flow`_
>>> - `Devlink health reporters`_
>>> - `Quality of service`_
>>>+- `RVU representors`_
>>>
>>> Overview
>>> ========
>>>@@ -340,3 +341,87 @@ Setup HTB offload
>>>         # tc class add dev <interface> parent 1: classid 1:2 htb rate
>>>10Gbit prio 2 quantum 188416
>>>
>>>         # tc class add dev <interface> parent 1: classid 1:3 htb rate
>>> 10Gbit prio 2 quantum 32768
>>>+
>>>+
>>>+RVU Representors
>>>+================
>>>+
>>>+RVU representor driver adds support for creation of representor
>>>+devices for RVU PFs' VFs in the system. Representor devices are
>>>+created when user enables the switchdev mode.
>>>+Switchdev mode can be enabled either before or after setting up SRIOV
>>numVFs.
>>>+All representor devices share a single NIXLF but each has a dedicated
>>>+queue (ie RQ/SQ. RVU PF representor driver registers a separate netdev
>>>+for each RQ/SQ queue pair.
>>>+
>>>+HW doesn't have a in-built switch which can do L2 learning and forward
>>>+pkts between representee and representor. Hence packet patch between
>>>+representee and it's representor is achieved by setting up appropriate NPC
>>MCAM filters.
>>>+Transmit packets matching these filters will be loopbacked through
>>>+hardware loopback channel/interface (ie instead of sending them out of
>>MAC interface).
>>>+Which will again match the installed filters and will be forwarded.
>>>+This way representee => representor and representor => representee
>>>+packet path is achieved.These rules get installed when representors
>>>+are created and gets active/deactivate based on the representor/representee
>>interface state.
>>>+
>>>+Usage example:
>>>+
>>>+ - List of devices on the system before vfs are created::
>>>+
>>>+	# devlink dev
>>>+	pci/0002:02:00.0
>>>+	pci/0002:1c:00.0
>>>+
>>>+- Change device to switchdev mode::
>>>+	# devlink dev eswitch set pci/0002:1c:00.0 mode switchdev
>>>+
>>>+ - List the devices on the system::
>>>+
>>>+	# ip link show
>>>+
>>>+Sample output::
>>>+
>>>+	# ip link show
>>>+	eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN
>>mode DEFAULT group default qlen 1000 link/ether 7e:58:2d:b6:97:51 brd
>>ff:ff:ff:ff:ff:ff
>>>+	r0p1v0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN
>>mode DEFAULT group default qlen 1000 link/ether 7e:5a:66:ea:fe:d6 brd
>>ff:ff:ff:ff:ff:ff
>>>+	r1p1v1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN
>>mode DEFAULT group default qlen 1000 link/ether de:29:be:10:9e:bf brd
>>ff:ff:ff:ff:ff:ff
>>>+	r2p1v2: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN
>>mode DEFAULT group default qlen 1000 link/ether 4a:12:c7:a2:66:ad brd
>>ff:ff:ff:ff:ff:ff
>>>+	r3p1v3: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN
>>mode
>>>+DEFAULT group default qlen 1000 link/ether c2:b8:a8:0e:73:fd brd
>>>+ff:ff:ff:ff:ff:ff
>>>+
>>>+
>>>+RVU representors can be managed using devlink ports (see
>>>+:ref:`Documentation/networking/devlink/devlink-port.rst <devlink_port>`)
>>interface.
>>>+
>>>+ - Show devlink ports of representors::
>>>+
>>>+	# devlink port
>>>+
>>>+Sample output::
>>>+
>>>+	pci/0002:1c:00.0/0: type eth netdev r0p1v0 flavour pcipf controller 0
>>pfnum 1 vfnum 0 external false splittable false
>>>+	pci/0002:1c:00.0/1: type eth netdev r1p1v1 flavour pcivf controller 0
>>pfnum 1 vfnum 1 external false splittable false
>>>+	pci/0002:1c:00.0/2: type eth netdev r2p1v2 flavour pcivf controller 0
>>pfnum 1 vfnum 2 external false splittable false
>>>+	pci/0002:1c:00.0/3: type eth netdev r3p1v3 flavour pcivf controller 0
>>>+pfnum 1 vfnum 3 external false splittable false
>>>+
>>>+Function attributes
>>>+===================
>>>+
>>>+The RVU representor support function attributes for representors Port
>>>+function configuration of the representors are supported through devlink
>>eswitch port.
>>>+
>>>+MAC address setup
>>>+-----------------
>>>+
>>>+RVU representor driver support devlink port function attr mechanism to
>>>+setup MAC address. (refer to
>>>+Documentation/networking/devlink/devlink-port.rst)
>>>+
>>>+ - To setup MAC address for port 2::
>>>+
>>>+	# devlink port function set  pci/0002:1c:00.0/2 hw_addr
>>>+5c:a1:1b:5e:43:11 state active
>>
>>Why you pass "state active" here? That is no-op for VFs.
>>
>>
>>>+
>>>+
>>>+To remove the representors from the system. Change the device to legacy
>>mode.
>>>+
>>>+ - Change device to legacy mode::
>>>+
>>>+	# devlink dev eswitch set pci/0002:1c:00.0 mode legacy
>>>diff --git a/drivers/net/ethernet/marvell/octeontx2/nic/otx2_devlink.c
>>>b/drivers/net/ethernet/marvell/octeontx2/nic/otx2_devlink.c
>>>index 53f14aa944bd..33ec9a7f7c03 100644
>>>--- a/drivers/net/ethernet/marvell/octeontx2/nic/otx2_devlink.c
>>>+++ b/drivers/net/ethernet/marvell/octeontx2/nic/otx2_devlink.c
>>>@@ -141,7 +141,56 @@ static const struct devlink_param otx2_dl_params[] =
>>{
>>> 			     otx2_dl_ucast_flt_cnt_validate),  };
>>>
>>>+#ifdef CONFIG_RVU_ESWITCH
>>>+static int otx2_devlink_eswitch_mode_get(struct devlink *devlink, u16
>>>+*mode) {
>>>+	struct otx2_devlink *otx2_dl = devlink_priv(devlink);
>>>+	struct otx2_nic *pfvf = otx2_dl->pfvf;
>>>+
>>>+	if (!otx2_rep_dev(pfvf->pdev))
>>>+		return -EOPNOTSUPP;
>>>+
>>>+	*mode = pfvf->esw_mode;
>>>+
>>>+	return 0;
>>>+}
>>>+
>>>+static int otx2_devlink_eswitch_mode_set(struct devlink *devlink, u16 mode,
>>>+					 struct netlink_ext_ack *extack)
>>>+{
>>>+	struct otx2_devlink *otx2_dl = devlink_priv(devlink);
>>>+	struct otx2_nic *pfvf = otx2_dl->pfvf;
>>>+	int ret = 0;
>>>+
>>>+	if (!otx2_rep_dev(pfvf->pdev))
>>>+		return -EOPNOTSUPP;
>>>+
>>>+	if (pfvf->esw_mode == mode)
>>>+		return 0;
>>>+
>>>+	switch (mode) {
>>>+	case DEVLINK_ESWITCH_MODE_LEGACY:
>>>+		rvu_rep_destroy(pfvf);
>>>+		break;
>>>+	case DEVLINK_ESWITCH_MODE_SWITCHDEV:
>>>+		ret = rvu_rep_create(pfvf, extack);
>>>+		break;
>>>+	default:
>>>+		return -EINVAL;
>>>+	}
>>>+
>>>+	if (!ret)
>>>+		pfvf->esw_mode = mode;
>>>+
>>>+	return ret;
>>>+}
>>>+#endif
>>>+
>>> static const struct devlink_ops otx2_devlink_ops = {
>>>+#ifdef CONFIG_RVU_ESWITCH
>>>+	.eswitch_mode_get = otx2_devlink_eswitch_mode_get,
>>>+	.eswitch_mode_set = otx2_devlink_eswitch_mode_set, #endif
>>> };
>>>
>>> int otx2_register_dl(struct otx2_nic *pfvf) diff --git
>>>a/drivers/net/ethernet/marvell/octeontx2/nic/rep.c
>>>b/drivers/net/ethernet/marvell/octeontx2/nic/rep.c
>>>index b0a0080e50d7..6ea5b4904a7c 100644
>>>--- a/drivers/net/ethernet/marvell/octeontx2/nic/rep.c
>>>+++ b/drivers/net/ethernet/marvell/octeontx2/nic/rep.c
>>>@@ -28,6 +28,164 @@ MODULE_DESCRIPTION(DRV_STRING);
>>>MODULE_LICENSE("GPL");  MODULE_DEVICE_TABLE(pci, rvu_rep_id_table);
>>>
>>>+static int rvu_rep_napi_init(struct otx2_nic *priv,
>>>+			     struct netlink_ext_ack *extack) {
>>>+	struct otx2_qset *qset = &priv->qset;
>>>+	struct otx2_cq_poll *cq_poll = NULL;
>>>+	struct otx2_hw *hw = &priv->hw;
>>>+	int err = 0, qidx, vec;
>>>+	char *irq_name;
>>>+
>>>+	qset->napi = kcalloc(hw->cint_cnt, sizeof(*cq_poll), GFP_KERNEL);
>>>+	if (!qset->napi)
>>>+		return -ENOMEM;
>>>+
>>>+	/* Register NAPI handler */
>>>+	for (qidx = 0; qidx < hw->cint_cnt; qidx++) {
>>>+		cq_poll = &qset->napi[qidx];
>>>+		cq_poll->cint_idx = qidx;
>>>+		cq_poll->cq_ids[CQ_RX] =
>>>+			(qidx <  hw->rx_queues) ? qidx : CINT_INVALID_CQ;
>>>+		cq_poll->cq_ids[CQ_TX] = (qidx < hw->tx_queues) ?
>>>+					  qidx + hw->rx_queues :
>>>+					  CINT_INVALID_CQ;
>>>+		cq_poll->cq_ids[CQ_XDP] = CINT_INVALID_CQ;
>>>+		cq_poll->cq_ids[CQ_QOS] = CINT_INVALID_CQ;
>>>+
>>>+		cq_poll->dev = (void *)priv;
>>>+		netif_napi_add(priv->reps[qidx]->netdev, &cq_poll->napi,
>>>+			       otx2_napi_handler);
>>>+		napi_enable(&cq_poll->napi);
>>>+	}
>>>+	/* Register CQ IRQ handlers */
>>>+	vec = hw->nix_msixoff + NIX_LF_CINT_VEC_START;
>>>+	for (qidx = 0; qidx < hw->cint_cnt; qidx++) {
>>>+		irq_name = &hw->irq_name[vec * NAME_SIZE];
>>>+
>>>+		snprintf(irq_name, NAME_SIZE, "rep%d-rxtx-%d", qidx, qidx);
>>>+
>>>+		err = request_irq(pci_irq_vector(priv->pdev, vec),
>>>+				  otx2_cq_intr_handler, 0, irq_name,
>>>+				  &qset->napi[qidx]);
>>>+		if (err) {
>>>+			NL_SET_ERR_MSG_FMT_MOD(extack,
>>>+					       "RVU REP IRQ registration failed for
>>CQ%d",
>>>+					       qidx);
>>>+			goto err_free_cints;
>>>+		}
>>>+		vec++;
>>>+
>>>+		/* Enable CQ IRQ */
>>>+		otx2_write64(priv, NIX_LF_CINTX_INT(qidx), BIT_ULL(0));
>>>+		otx2_write64(priv, NIX_LF_CINTX_ENA_W1S(qidx), BIT_ULL(0));
>>>+	}
>>>+	priv->flags &= ~OTX2_FLAG_INTF_DOWN;
>>>+	return 0;
>>>+
>>>+err_free_cints:
>>>+	otx2_free_cints(priv, qidx);
>>>+	otx2_disable_napi(priv);
>>>+	return err;
>>>+}
>>>+
>>>+static void rvu_rep_free_cq_rsrc(struct otx2_nic *priv) {
>>>+	struct otx2_qset *qset = &priv->qset;
>>>+	struct otx2_cq_poll *cq_poll = NULL;
>>>+	int qidx, vec;
>>>+
>>>+	/* Cleanup CQ NAPI and IRQ */
>>>+	vec = priv->hw.nix_msixoff + NIX_LF_CINT_VEC_START;
>>>+	for (qidx = 0; qidx < priv->hw.cint_cnt; qidx++) {
>>>+		/* Disable interrupt */
>>>+		otx2_write64(priv, NIX_LF_CINTX_ENA_W1C(qidx),
>>BIT_ULL(0));
>>>+
>>>+		synchronize_irq(pci_irq_vector(priv->pdev, vec));
>>>+
>>>+		cq_poll = &qset->napi[qidx];
>>>+		napi_synchronize(&cq_poll->napi);
>>>+		vec++;
>>>+	}
>>>+	otx2_free_cints(priv, priv->hw.cint_cnt);
>>>+	otx2_disable_napi(priv);
>>>+}
>>>+
>>>+void rvu_rep_destroy(struct otx2_nic *priv) {
>>>+	struct rep_dev *rep;
>>>+	int rep_id;
>>>+
>>>+	priv->flags |= OTX2_FLAG_INTF_DOWN;
>>>+	rvu_rep_free_cq_rsrc(priv);
>>>+	for (rep_id = 0; rep_id < priv->rep_cnt; rep_id++) {
>>>+		rep = priv->reps[rep_id];
>>>+		unregister_netdev(rep->netdev);
>>>+		free_netdev(rep->netdev);
>>>+	}
>>>+	kfree(priv->reps);
>>>+}
>>>+
>>>+int rvu_rep_create(struct otx2_nic *priv, struct netlink_ext_ack
>>>+*extack) {
>>>+	int rep_cnt = priv->rep_cnt;
>>>+	struct net_device *ndev;
>>>+	struct rep_dev *rep;
>>>+	int rep_id, err;
>>>+	u16 pcifunc;
>>>+
>>>+	priv->reps = kcalloc(rep_cnt, sizeof(struct rep_dev *), GFP_KERNEL);
>>>+	if (!priv->reps)
>>>+		return -ENOMEM;
>>>+
>>>+	for (rep_id = 0; rep_id < rep_cnt; rep_id++) {
>>>+		ndev = alloc_etherdev(sizeof(*rep));
>>>+		if (!ndev) {
>>>+			NL_SET_ERR_MSG_FMT_MOD(extack,
>>>+					       "PFVF representor:%d creation
>>failed",
>>>+					       rep_id);
>>>+			err = -ENOMEM;
>>>+			goto exit;
>>>+		}
>>>+
>>>+		rep = netdev_priv(ndev);
>>>+		priv->reps[rep_id] = rep;
>>>+		rep->mdev = priv;
>>>+		rep->netdev = ndev;
>>>+		rep->rep_id = rep_id;
>>>+
>>>+		ndev->min_mtu = OTX2_MIN_MTU;
>>>+		ndev->max_mtu = priv->hw.max_mtu;
>>>+		pcifunc = priv->rep_pf_map[rep_id];
>>>+		rep->pcifunc = pcifunc;
>>>+
>>>+		snprintf(ndev->name, sizeof(ndev->name), "r%dp%d", rep_id,
>>>+			 rvu_get_pf(pcifunc));
>>>+
>>>+		eth_hw_addr_random(ndev);
>>>+		err = register_netdev(ndev);
>>
>>I don't follow. You just create netdevices, no devlink ports. That is inconsistent
>>with your documentation above.
>Creation on devlink port is implemented in patch 10 " octeontx2-pf: Add devlink port support".

So adjust the docs here to be consistent with the code and add the parts
of documentation alonside with the support in patch 10.


>>
>>
>>>+		if (err) {
>>>+			NL_SET_ERR_MSG_MOD(extack,
>>>+					   "PFVF reprentator registration
>>failed");
>>>+			free_netdev(ndev);
>>>+			goto exit;
>>>+		}
>>>+	}
>>>+	err = rvu_rep_napi_init(priv, extack);
>>>+	if (err)
>>>+		goto exit;
>>>+
>>>+	return 0;
>>>+exit:
>>>+	while (--rep_id >= 0) {
>>>+		rep = priv->reps[rep_id];
>>>+		unregister_netdev(rep->netdev);
>>>+		free_netdev(rep->netdev);
>>>+	}
>>>+	kfree(priv->reps);
>>>+	return err;
>>>+}
>>>+
>>> static void rvu_rep_rsrc_free(struct otx2_nic *priv)  {
>>> 	struct otx2_qset *qset = &priv->qset; @@ -167,6 +325,10 @@ static int
>>>rvu_rep_probe(struct pci_dev *pdev, const struct pci_device_id *id)
>>> 	if (err)
>>> 		goto err_detach_rsrc;
>>>
>>>+	err = otx2_register_dl(priv);
>>>+	if (err)
>>>+		goto err_detach_rsrc;
>>>+
>>> 	return 0;
>>>
>>> err_detach_rsrc:
>>>@@ -188,6 +350,9 @@ static void rvu_rep_remove(struct pci_dev *pdev)  {
>>> 	struct otx2_nic *priv = pci_get_drvdata(pdev);
>>>
>>>+	otx2_unregister_dl(priv);
>>>+	if (!(priv->flags & OTX2_FLAG_INTF_DOWN))
>>>+		rvu_rep_destroy(priv);
>>> 	rvu_rep_rsrc_free(priv);
>>> 	otx2_detach_resources(&priv->mbox);
>>> 	if (priv->hw.lmt_info)
>>>diff --git a/drivers/net/ethernet/marvell/octeontx2/nic/rep.h
>>>b/drivers/net/ethernet/marvell/octeontx2/nic/rep.h
>>>index 565e75628df2..c04874c4d4c6 100644
>>>--- a/drivers/net/ethernet/marvell/octeontx2/nic/rep.h
>>>+++ b/drivers/net/ethernet/marvell/octeontx2/nic/rep.h
>>>@@ -28,4 +28,7 @@ static inline bool otx2_rep_dev(struct pci_dev *pdev)
>>>{
>>> 	return pdev->device == PCI_DEVID_RVU_REP;  }
>>>+
>>>+int rvu_rep_create(struct otx2_nic *priv, struct netlink_ext_ack
>>>+*extack); void rvu_rep_destroy(struct otx2_nic *priv);
>>> #endif /* REP_H */
>>>--
>>>2.25.1
>>>
>>>