From: Hans de Goede <hdegoede@redhat.com>
To: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Lee Jones <lee.jones@linaro.org>,
Andy Shevchenko <andy@infradead.org>,
Mika Westerberg <mika.westerberg@linux.intel.com>,
Linux Kernel Mailing List <linux-kernel@vger.kernel.org>,
Laurent Pinchart <laurent.pinchart@ideasonboard.com>,
Dan Scally <djrscally@gmail.com>, Kate Hsuan <hpa@redhat.com>,
Maximilian Luz <luzmaximilian@gmail.com>
Subject: Re: [PATCH] mfd: intel-lpss: Fix I2C4 not being available on the Microsoft Surface Go & Go 2
Date: Fri, 3 Dec 2021 12:32:35 +0100 [thread overview]
Message-ID: <a2d551d3-7426-1dff-9936-d4bde10c4a59@redhat.com> (raw)
In-Reply-To: <CAHp75VctFk8xO4ddWi1V49eNp5+h_AOcRVv_=iMnjmVt0TOM5w@mail.gmail.com>
Hi,
On 12/2/21 22:15, Andy Shevchenko wrote:
> On Thu, Dec 2, 2021 at 10:14 PM Hans de Goede <hdegoede@redhat.com> wrote:
>>
>> Many DSDTs for Kaby Lake and Kaby Lake Refresh models contain a
>> _SB.PCI0.GEXP ACPI Device node describing an I2C attached GPIO expander.
>
> For the record (and probably good to mention it's here) it's a PCA953x
> compatible one.
Ack, added to the commit msg for v2.
>> This seems to be something which is copy and pasted from the DSDT
>> from some reference design since this ACPI Device is present even on
>> models where no such GPIO expander is used at all, such as on the
>> Microsoft Surface Go & Go 2.
>
> Does this come from schematics? Or..? Ah, I see below.
>
>> This ACPI Device is a problem because it contains a SystemMemory
>> OperationRegion which covers the MMIO for the I2C4 I2C controller this
>> causes the MFD cell for the I2C4 controller to not be instantiated due
>> to a resource conflict, requiring the use of acpi_enforce_resources=lax
>> to work around this.
>
> Right.
>
>> I have done an extensive analysis of all the ACPI tables on the
>> Microsoft Surface Go and the _SB.PCI0.GEXP ACPI Device's methods are
>> not used by any code in the ACPI tables, neither are any of them
>> directly called by any Linux kernel code. This is unsurprising since
>> running i2cdetect on the I2C4 bus shows that there is no GPIO
>> expander chip present on these devices at all.
>
> I believe it's an optional component on our reference designs (I saw a
> lot of those expanders on our development boards).
>
>> This commit adds a PCI subsystem vendor:device table listing PCI devices
>> where it is known to be safe to ignore a resource-conflicts with ACPI
>
> ignore resource conflicts
Ack, fixed for v2.
> (no article, no dash) ?
>
>> declared SystemMemory regions.
>>
>> This makes the I2C4 bus work out of the box on the Microsoft Surface
>> Go & Go 2, which is necessary for the cameras on these devices to work.
>
> After addressing comments
> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
> Thanks for the patch!
>
>> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
>> Cc: Dan Scally <djrscally@gmail.com>
>> Cc: Kate Hsuan <hpa@redhat.com>
>> Cc: Maximilian Luz <luzmaximilian@gmail.com>
>> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
>> ---
>> drivers/mfd/intel-lpss-pci.c | 12 ++++++++++++
>> drivers/mfd/intel-lpss.c | 1 +
>> drivers/mfd/intel-lpss.h | 1 +
>> 3 files changed, 14 insertions(+)
>>
>> diff --git a/drivers/mfd/intel-lpss-pci.c b/drivers/mfd/intel-lpss-pci.c
>> index a872b4485eac..593290ff08a6 100644
>> --- a/drivers/mfd/intel-lpss-pci.c
>> +++ b/drivers/mfd/intel-lpss-pci.c
>> @@ -17,6 +17,15 @@
>>
>> #include "intel-lpss.h"
>>
>> +/* Some DSDTs have an unused GEXP ACPI device conflicting with I2C4 resources */
>> +static const struct pci_device_id ignore_resource_conflicts_ids[] = {
>> + /* Microsoft Surface Go (version 1) I2C4 */
>> + { PCI_DEVICE_SUB(0x8086, 0x9d64, 0x152d, 0x1182), },
>> + /* Microsoft Surface Go 2 I2C4 */
>> + { PCI_DEVICE_SUB(0x8086, 0x9d64, 0x152d, 0x1237), },
>
> Can we use PCI_VENDOR_ID_INTEL?
Done for v2.
Thank you for the review.
Regards,
Hans
>
>> + { }
>> +};
>> +
>> static int intel_lpss_pci_probe(struct pci_dev *pdev,
>> const struct pci_device_id *id)
>> {
>> @@ -35,6 +44,9 @@ static int intel_lpss_pci_probe(struct pci_dev *pdev,
>> info->mem = &pdev->resource[0];
>> info->irq = pdev->irq;
>>
>> + if (pci_match_id(ignore_resource_conflicts_ids, pdev))
>> + info->ignore_resource_conflicts = true;
>> +
>> pdev->d3cold_delay = 0;
>>
>> /* Probably it is enough to set this for iDMA capable devices only */
>> diff --git a/drivers/mfd/intel-lpss.c b/drivers/mfd/intel-lpss.c
>> index 0e15afc39f54..cfbee2cfba6b 100644
>> --- a/drivers/mfd/intel-lpss.c
>> +++ b/drivers/mfd/intel-lpss.c
>> @@ -401,6 +401,7 @@ int intel_lpss_probe(struct device *dev,
>> return ret;
>>
>> lpss->cell->swnode = info->swnode;
>> + lpss->cell->ignore_resource_conflicts = info->ignore_resource_conflicts;
>>
>> intel_lpss_init_dev(lpss);
>>
>> diff --git a/drivers/mfd/intel-lpss.h b/drivers/mfd/intel-lpss.h
>> index 22dbc4aed793..062ce95b68b9 100644
>> --- a/drivers/mfd/intel-lpss.h
>> +++ b/drivers/mfd/intel-lpss.h
>> @@ -19,6 +19,7 @@ struct software_node;
>>
>> struct intel_lpss_platform_info {
>> struct resource *mem;
>> + bool ignore_resource_conflicts;
>> int irq;
>> unsigned long clk_rate;
>> const char *clk_con_id;
>> --
>> 2.33.1
>>
>
>
prev parent reply other threads:[~2021-12-03 11:32 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-12-02 20:13 Hans de Goede
2021-12-02 20:43 ` Laurent Pinchart
2021-12-03 11:29 ` Hans de Goede
2021-12-02 21:15 ` Andy Shevchenko
2021-12-03 11:32 ` Hans de Goede [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=a2d551d3-7426-1dff-9936-d4bde10c4a59@redhat.com \
--to=hdegoede@redhat.com \
--cc=andy.shevchenko@gmail.com \
--cc=andy@infradead.org \
--cc=djrscally@gmail.com \
--cc=hpa@redhat.com \
--cc=laurent.pinchart@ideasonboard.com \
--cc=lee.jones@linaro.org \
--cc=linux-kernel@vger.kernel.org \
--cc=luzmaximilian@gmail.com \
--cc=mika.westerberg@linux.intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®