From: Ping-Ke Shih <pkshih@realtek.com>
To: Enver Ikromov <owner@ph4ntom-rev.uz>
Cc: "linux-wireless@vger.kernel.org" <linux-wireless@vger.kernel.org>,
"linux-kernel@vger.kernel.org" <linux-kernel@vger.kernel.org>
Subject: RE: [PATCH rtw-next v5 09/10] wifi: rtw89: honor ASSIGN_SEQ, retries, and NO_ACK for injected frames
Date: Mon, 16 Nov 2026 03:00:10 +0000 [thread overview]
Message-ID: <a56a85ff19dc4bd29cb3c81cb7e0c77a@realtek.com> (raw)
In-Reply-To: <20261113235211.1911-10-owner@ph4ntom-rev.uz>
Enver Ikromov <owner@ph4ntom-rev.uz> wrote:
> For injected frames, rtw89_core_tx_update_injection() only applies
> the radiotap rate and leaves several TX descriptor and completion
> settings mismatched with the radiotap flags:
>
> - The management path sets hw_ssn_sel/hw_seq_mode (and MLO links set
> upd_wlan_hdr), overwriting user-supplied sequence numbers when
> IEEE80211_TX_CTL_ASSIGN_SEQ is not set, and leaving hw_seq_mode
> enabled even on injected control frames that have no seq_ctrl field.
> Conversely, injected data frames leave hw_seq_mode unset when
> ASSIGN_SEQ is requested on a monitor interface.
> - Unicast frames unconditionally set RTS_EN = 1 and HW_RTS_EN = 1 in
> txwd_info4. On normal traffic HW_RTS_EN = 1 gates RTS on the MAC
> length/duration threshold (4080B / 2816us), whereas for injected
> frames RTS_EN must follow IEEE80211_TX_RC_USE_RTS_CTS with
> HW_RTS_EN = 0 so short frames requesting RTS/CTS actually emit RTS.
No need to describe driver behavior.
> - IEEE80211_TX_CTL_NO_ACK (e.g. IEEE80211_RADIOTAP_F_TX_NOACK) neither
> sets BE_TXD_BODY6_NO_ACK on Wi-Fi 7 descriptors nor bounds retries,
> causing unacknowledged frames to be retransmitted up to the retry
> limit. Note that Wi-Fi 6 TXWD v0 chips (RTL8852A/B, RTL8851B) have
> no dedicated per-packet NO_ACK descriptor bit and rely on
> tx_cnt_lmt = 1 to suppress retransmissions; when that single attempt
> completes with RTW89_TX_RETRY_LIMIT, suppress false tx_retry_lmt
> accounting in rtw89_pci_tx_status() and set
> IEEE80211_TX_STAT_NOACK_TRANSMITTED in rtw89_tx_rpt_tx_status() too.
> - hw->max_rate_tries is left at the mac80211 default (4), truncating
> IEEE80211_RADIOTAP_DATA_RETRIES, and info->control.rates[0].count is
> ignored when a radiotap rate is specified.
> - Positive radiotap HT/VHT/legacy rate indices are added to the table
> base without clamping to the chip's valid MCS or legacy rate bounds.
>
> Configure hardware sequence assignment according to
> IEEE80211_TX_CTL_ASSIGN_SEQ (and never on control frames), drive
> rts_en and hw_rts_en for radiotap RTS/CTS, advertise
> RTW89_TX_DATA_CNT_LMT_MAX (63) in hw->max_rate_tries, honor
> rates[0].count and NO_ACK descriptor/status semantics, and clamp
> positive radiotap rate indices to valid hardware ranges.
>
> Signed-off-by: Enver Ikromov <owner@ph4ntom-rev.uz>
> ---
> drivers/net/wireless/realtek/rtw89/core.c | 63 ++++++++++++++++++-----
> drivers/net/wireless/realtek/rtw89/core.h | 4 ++
> drivers/net/wireless/realtek/rtw89/mac.h | 2 +
> drivers/net/wireless/realtek/rtw89/pci.c | 3 +-
> 4 files changed, 58 insertions(+), 14 deletions(-)
>
> diff --git a/drivers/net/wireless/realtek/rtw89/core.c b/drivers/net/wireless/realtek/rtw89/core.c
> index 84c12c6..7d174d2 100644
> --- a/drivers/net/wireless/realtek/rtw89/core.c
> +++ b/drivers/net/wireless/realtek/rtw89/core.c
> @@ -1252,12 +1252,43 @@ static void rtw89_core_tx_update_injection(struct rtw89_dev *rtwdev,
> const struct rtw89_hw_rate_def *hw_rate = &rtw89_hw_rate[rtwdev->chip->chip_gen];
> enum mac80211_rate_control_flags flags = info->control.rates[0].flags;
> struct rtw89_tx_desc_info *desc_info = &tx_req->desc_info;
> + struct ieee80211_hdr *hdr = (void *)tx_req->skb->data;
> const struct rtw89_chan *chan;
> s8 idx = info->control.rates[0].idx;
> - u8 nss, mcs;
> + u8 nss, mcs, max_mcs;
>
> desc_info->use_rate = true;
> desc_info->dis_data_fb = true;
> + desc_info->hw_rts_en = false;
> + desc_info->rts_en = (flags & IEEE80211_TX_RC_USE_RTS_CTS) &&
> + !desc_info->is_bmc &&
> + !(info->flags & IEEE80211_TX_CTL_NO_ACK);
> +
> + /* Control frames have no seq_ctrl field; otherwise keep the
> + * sequence number supplied by user space unless ASSIGN_SEQ is set.
> + */
> + if (!(info->flags & IEEE80211_TX_CTL_ASSIGN_SEQ) ||
> + ieee80211_is_ctl(hdr->frame_control)) {
> + desc_info->upd_wlan_hdr = false;
Does it need to update this?
> + desc_info->hw_ssn_sel = 0;
> + desc_info->hw_seq_mode = 0;
> + } else {
> + desc_info->hw_ssn_sel = RTW89_MGMT_HW_SSN_SEL;
> + desc_info->hw_seq_mode = RTW89_MGMT_HW_SEQ_MODE;
This is only for MGMT frames. If you inject QoS data frames, the sequence
number should count per TID. But for injection it seems not build BA seesion
, so this is harmless.
> + }
> +
> + /* Suppress hardware retransmissions (and ACK waiting on BE) for NO_ACK;
> + * otherwise honor explicit radiotap retry limits when a rate is set.
> + */
First line of block comment should be empty.
But this comment is not necessary. The code explains itself.
> + if (info->flags & IEEE80211_TX_CTL_NO_ACK) {
> + desc_info->no_ack = true;
> + desc_info->tx_cnt_lmt_en = true;
> + desc_info->tx_cnt_lmt = 1;
> + } else if (info->control.rates[0].count) {
> + desc_info->tx_cnt_lmt_en = true;
> + desc_info->tx_cnt_lmt = umin(info->control.rates[0].count,
> + RTW89_TX_DATA_CNT_LMT_MAX);
You have set
hw->max_rate_tries = RTW89_TX_DATA_CNT_LMT_MAX;
Is it still necessary to have umin()?
> + }
>
> /* No rate was given in the radiotap header. Management frames
> * already carry the rate from rtw89_core_tx_update_mgmt_info(), so
> @@ -1283,16 +1314,20 @@ static void rtw89_core_tx_update_injection(struct rtw89_dev *rtwdev,
> desc_info->gi_ltf = 1;
>
> if (flags & IEEE80211_TX_RC_VHT_MCS) {
> + max_mcs = rtwdev->chip->chip_gen == RTW89_CHIP_BE ? 11 : 9;
I think the maximum standard VHT MCS rate is 9. Just use 9 inline.
> nss = umin(idx >> 4, ARRAY_SIZE(hw_rate->vht) - 1);
> - mcs = idx & 0xf;
> + mcs = umin(idx & 0xf, max_mcs);
> desc_info->data_rate = hw_rate->vht[nss] + mcs;
> } else if (flags & IEEE80211_TX_RC_MCS) {
> - desc_info->data_rate = hw_rate->ht + idx;
> + desc_info->data_rate = hw_rate->ht + umin(idx, 31);
> } else {
> chan = rtw89_chan_get(rtwdev, tx_req->rtwvif_link->chanctx_idx);
> -
> - desc_info->data_rate = idx + (chan->band_type == RTW89_BAND_2G ?
> - RTW89_HW_RATE_CCK1 : RTW89_HW_RATE_OFDM6);
> + if (chan->band_type == RTW89_BAND_2G)
> + desc_info->data_rate = RTW89_HW_RATE_CCK1 +
> + umin(idx, 11);
> + else
> + desc_info->data_rate = RTW89_HW_RATE_OFDM6 +
> + umin(idx, 7);
> }
> }
>
[...]
> diff --git a/drivers/net/wireless/realtek/rtw89/pci.c b/drivers/net/wireless/realtek/rtw89/pci.c
> index 6d19e75..6c4d6c0 100644
> --- a/drivers/net/wireless/realtek/rtw89/pci.c
> +++ b/drivers/net/wireless/realtek/rtw89/pci.c
> @@ -475,7 +475,8 @@ static void rtw89_pci_tx_status(struct rtw89_dev *rtwdev,
> if (tx_status == RTW89_TX_DONE) {
> info->flags |= IEEE80211_TX_STAT_ACK;
> tx_ring->tx_acked++;
> - } else {
> + } else if (!(info->flags & IEEE80211_TX_CTL_NO_ACK) ||
> + tx_status != RTW89_TX_RETRY_LIMIT) {
Will it be a problem without this change?
This branch is only to sum internal counters of the driver.
> if (info->flags & IEEE80211_TX_CTL_REQ_TX_STATUS)
> rtw89_debug(rtwdev, RTW89_DBG_FW,
> "failed to TX of status %x\n", tx_status);
> --
> 2.56.0.windows.4
next prev parent reply other threads:[~2026-11-16 3:00 UTC|newest]
Thread overview: 21+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-11-13 23:52 [PATCH rtw-next v5 00/10] wifi: rtw89: monitor mode RX filter and raw frame injection fixes Enver Ikromov
2026-11-13 23:52 ` [PATCH rtw-next v5 01/10] wifi: rtw89: avoid NULL vif dereference in rtw89_ops_tx() Enver Ikromov
2026-11-15 3:23 ` Ping-Ke Shih
2026-11-13 23:52 ` [PATCH rtw-next v5 02/10] wifi: rtw89: handle negative rate index for injected frames Enver Ikromov
2026-11-15 3:38 ` Ping-Ke Shih
2026-11-13 23:52 ` [PATCH rtw-next v5 03/10] wifi: rtw89: fix RX filter configuration for monitor mode Enver Ikromov
2026-11-15 3:48 ` Ping-Ke Shih
2026-11-13 23:52 ` [PATCH rtw-next v5 04/10] wifi: rtw89: protect pure_monitor_mode_vif with RCU Enver Ikromov
2026-11-15 4:00 ` Ping-Ke Shih
2026-11-13 23:52 ` [PATCH rtw-next v5 05/10] wifi: rtw89: use AP self role for monitor interfaces Enver Ikromov
2026-11-15 4:08 ` Ping-Ke Shih
2026-11-13 23:52 ` [PATCH rtw-next v5 06/10] wifi: rtw89: transmit frames from " Enver Ikromov
2026-11-16 1:35 ` Ping-Ke Shih
2026-11-13 23:52 ` [PATCH rtw-next v5 07/10] wifi: rtw89: send injected control frames through the management path Enver Ikromov
2026-11-16 2:14 ` Ping-Ke Shih
2026-11-13 23:52 ` [PATCH rtw-next v5 08/10] wifi: rtw89: skip host-side TX hooks for injected frames Enver Ikromov
2026-11-16 2:20 ` Ping-Ke Shih
2026-11-13 23:52 ` [PATCH rtw-next v5 09/10] wifi: rtw89: honor ASSIGN_SEQ, retries, and NO_ACK " Enver Ikromov
2026-11-16 3:00 ` Ping-Ke Shih [this message]
2026-11-13 23:52 ` [PATCH rtw-next v5 10/10] wifi: rtw89: restore channel when leaving idle on non-chanctx devices Enver Ikromov
2026-11-15 3:12 ` [PATCH rtw-next v5 00/10] wifi: rtw89: monitor mode RX filter and raw frame injection fixes Ping-Ke Shih
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=a56a85ff19dc4bd29cb3c81cb7e0c77a@realtek.com \
--to=pkshih@realtek.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-wireless@vger.kernel.org \
--cc=owner@ph4ntom-rev.uz \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®