Re: [PATCH] net: phy: at803x: Use helpers to access MMD PHY registers

[Heiner Kallweit <hkallweit1@gmail.com>]

On 25.01.2019 16:00, Andrew Lunn wrote:
> On Fri, Jan 25, 2019 at 12:35:10PM +0000, Carlo Caione wrote:
>> Libphy provides a standard set of helpers to access the MMD PHY
>> registers. Use those instead of relying on custom driver-specific
>> functions.
> 
> Hi Carlo
> 
> Maybe deja vu, but i thought a similar patch went by recently?
> 
Andrew, maybe you mean this one?

9b420eff9fcf ("net: phy: micrel: use phy_read_mmd and phy_write_mmd")

> Anyway,
> 
> Reviewed-by: Andrew Lunn <andrew@lunn.ch>
> 
>     Andrew
> 
>>
>> Signed-off-by: Carlo Caione <ccaione@baylibre.com>
>> ---
>>  drivers/net/phy/at803x.c | 16 +++-------------
>>  1 file changed, 3 insertions(+), 13 deletions(-)
>>
>> diff --git a/drivers/net/phy/at803x.c b/drivers/net/phy/at803x.c
>> index f9432d053a22..23ba76f8d950 100644
>> --- a/drivers/net/phy/at803x.c
>> +++ b/drivers/net/phy/at803x.c
>> @@ -39,9 +39,6 @@
>>  #define AT803X_LOC_MAC_ADDR_0_15_OFFSET		0x804C
>>  #define AT803X_LOC_MAC_ADDR_16_31_OFFSET	0x804B
>>  #define AT803X_LOC_MAC_ADDR_32_47_OFFSET	0x804A
>> -#define AT803X_MMD_ACCESS_CONTROL		0x0D
>> -#define AT803X_MMD_ACCESS_CONTROL_DATA		0x0E
>> -#define AT803X_FUNC_DATA			0x4003
>>  #define AT803X_REG_CHIP_CONFIG			0x1f
>>  #define AT803X_BT_BX_REG_SEL			0x8000
>>  
>> @@ -168,16 +165,9 @@ static int at803x_set_wol(struct phy_device *phydev,
>>  		if (!is_valid_ether_addr(mac))
>>  			return -EINVAL;
>>  
>> -		for (i = 0; i < 3; i++) {
>> -			phy_write(phydev, AT803X_MMD_ACCESS_CONTROL,
>> -				  AT803X_DEVICE_ADDR);
>> -			phy_write(phydev, AT803X_MMD_ACCESS_CONTROL_DATA,
>> -				  offsets[i]);
>> -			phy_write(phydev, AT803X_MMD_ACCESS_CONTROL,
>> -				  AT803X_FUNC_DATA);
>> -			phy_write(phydev, AT803X_MMD_ACCESS_CONTROL_DATA,
>> -				  mac[(i * 2) + 1] | (mac[(i * 2)] << 8));
>> -		}
>> +		for (i = 0; i < 3; i++)
>> +			phy_write_mmd(phydev, AT803X_DEVICE_ADDR, offsets[i],
>> +				      mac[(i * 2) + 1] | (mac[(i * 2)] << 8));
>>  
>>  		value = phy_read(phydev, AT803X_INTR_ENABLE);
>>  		value |= AT803X_INTR_ENABLE_WOL;
>> -- 
>> 2.19.1
>>
> .
>