From: Michal Simek <michal.simek@amd.com>
To: <linux-kernel@vger.kernel.org>, <monstr@monstr.eu>,
<michal.simek@amd.com>, <git@amd.com>
Cc: Shaikh Mohammed Suhan <suhan.sm@amd.com>,
Conor Dooley <conor+dt@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Rob Herring <robh@kernel.org>,
"open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS"
<devicetree@vger.kernel.org>,
"moderated list:ARM/ZYNQ ARCHITECTURE"
<linux-arm-kernel@lists.infradead.org>
Subject: [PATCH 3/3] arm64: zynqmp: dts: Add USB hub supply regulators to SOMs
Date: Thu, 19 Nov 2026 16:40:44 +0100 [thread overview]
Message-ID: <a807fea2b2af7c1b068ba375842efda44c0f0dac.1795102838.git.michal.simek@amd.com> (raw)
In-Reply-To: <cover.1795102838.git.michal.simek@amd.com>
From: Shaikh Mohammed Suhan <suhan.sm@amd.com>
Add fixed supply regulators for the onboard USB hub (USB5744).
The USB hub requires two always-on power rails:
- vdd: 3.3V main supply
- vdd2: auxiliary supply
Model these rails as fixed regulators and reference them from the hub
node to accurately describe the hardware.
Signed-off-by: Shaikh Mohammed Suhan <suhan.sm@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
---
.../boot/dts/xilinx/zynqmp-sck-kd-g-revA.dtso | 20 +++++++++++++++++
.../boot/dts/xilinx/zynqmp-sck-kr-g-revA.dtso | 22 +++++++++++++++++++
.../boot/dts/xilinx/zynqmp-sck-kr-g-revB.dtso | 22 +++++++++++++++++++
.../boot/dts/xilinx/zynqmp-sck-kv-g-revA.dtso | 20 +++++++++++++++++
.../boot/dts/xilinx/zynqmp-sck-kv-g-revB.dtso | 20 +++++++++++++++++
5 files changed, 104 insertions(+)
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-sck-kd-g-revA.dtso b/arch/arm64/boot/dts/xilinx/zynqmp-sck-kd-g-revA.dtso
index d20b6ea2ad0b..ba5d761805a7 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-sck-kd-g-revA.dtso
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-sck-kd-g-revA.dtso
@@ -50,6 +50,24 @@ slg_delay: enable-delay {
gpio-controller;
gpios = <&slg7xl45106 3 GPIO_ACTIVE_LOW>;
};
+
+ vdd_usb_hub: regulator-vdd-usb-hub {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd_usb_hub";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vdd2_usb_hub: regulator-vdd2-usb-hub {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd2_usb_hub";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
};
&can0 {
@@ -123,6 +141,8 @@ hub_2_0: hub@1 {
peer-hub = <&hub_3_0>;
i2c-bus = <&hub>;
reset-gpios = <&slg_delay 0 10000 10000>;
+ vdd-supply = <&vdd_usb_hub>;
+ vdd2-supply = <&vdd2_usb_hub>;
};
/* 3.0 hub on port 2 */
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-sck-kr-g-revA.dtso b/arch/arm64/boot/dts/xilinx/zynqmp-sck-kr-g-revA.dtso
index b3084f44a4ca..791ae9954173 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-sck-kr-g-revA.dtso
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-sck-kr-g-revA.dtso
@@ -86,6 +86,24 @@ slg_delay: enable-delay {
gpios = <&slg7xl45106 3 GPIO_ACTIVE_LOW>,
<&slg7xl45106 4 GPIO_ACTIVE_LOW>;
};
+
+ vdd_usb_hub: regulator-vdd-usb-hub {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd_usb_hub";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vdd2_usb_hub: regulator-vdd2-usb-hub {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd2_usb_hub";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
};
&i2c1 { /* I2C_SCK C26/C27 - MIO from SOM */
@@ -194,6 +212,8 @@ hub_2_0: hub@1 {
peer-hub = <&hub_3_0>;
i2c-bus = <&hub_1>;
reset-gpios = <&slg_delay 0 10000 10000>;
+ vdd-supply = <&vdd_usb_hub>;
+ vdd2-supply = <&vdd2_usb_hub>;
};
/* 3.0 hub on port 2 */
@@ -232,6 +252,8 @@ hub1_2_0: hub@1 {
peer-hub = <&hub1_3_0>;
i2c-bus = <&hub_2>;
reset-gpios = <&slg_delay 1 10000 10000>;
+ vdd-supply = <&vdd_usb_hub>;
+ vdd2-supply = <&vdd2_usb_hub>;
};
/* 3.0 hub on port 2 */
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-sck-kr-g-revB.dtso b/arch/arm64/boot/dts/xilinx/zynqmp-sck-kr-g-revB.dtso
index fdb6eae87eb9..b9ae01cddcae 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-sck-kr-g-revB.dtso
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-sck-kr-g-revB.dtso
@@ -87,6 +87,24 @@ slg_delay: enable-delay {
gpios = <&slg7xl45106 3 GPIO_ACTIVE_LOW>,
<&slg7xl45106 4 GPIO_ACTIVE_LOW>;
};
+
+ vdd_usb_hub: regulator-vdd-usb-hub {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd_usb_hub";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vdd2_usb_hub: regulator-vdd2-usb-hub {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd2_usb_hub";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
};
&i2c1 { /* I2C_SCK C26/C27 - MIO from SOM */
@@ -195,6 +213,8 @@ hub_2_0: hub@1 {
peer-hub = <&hub_3_0>;
i2c-bus = <&hub_1>;
reset-gpios = <&slg_delay 0 10000 10000>;
+ vdd-supply = <&vdd_usb_hub>;
+ vdd2-supply = <&vdd2_usb_hub>;
};
/* 3.0 hub on port 2 */
@@ -233,6 +253,8 @@ hub1_2_0: hub@1 {
peer-hub = <&hub1_3_0>;
i2c-bus = <&hub_2>;
reset-gpios = <&slg_delay 1 10000 10000>;
+ vdd-supply = <&vdd_usb_hub>;
+ vdd2-supply = <&vdd2_usb_hub>;
};
/* 3.0 hub on port 2 */
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revA.dtso b/arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revA.dtso
index 09ed585cf91d..9b37cff42e26 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revA.dtso
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revA.dtso
@@ -85,6 +85,24 @@ slg_delay: enable-delay {
gpio-controller;
gpios = <&gpio 44 GPIO_ACTIVE_LOW>;
};
+
+ vdd_usb_hub: regulator-vdd-usb-hub {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd_usb_hub";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vdd2_usb_hub: regulator-vdd2-usb-hub {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd2_usb_hub";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
};
&i2c1 { /* I2C_SCK C23/C24 - MIO from SOM */
@@ -167,6 +185,8 @@ hub_2_0: hub@1 {
reg = <1>;
peer-hub = <&hub_3_0>;
reset-gpios = <&slg_delay 0 10000 10000>;
+ vdd-supply = <&vdd_usb_hub>;
+ vdd2-supply = <&vdd2_usb_hub>;
};
/* 3.0 hub on port 2 */
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revB.dtso b/arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revB.dtso
index 50f451bcc7aa..657aa73f741c 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revB.dtso
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revB.dtso
@@ -81,6 +81,24 @@ slg_delay: enable-delay {
gpio-controller;
gpios = <&gpio 44 GPIO_ACTIVE_LOW>;
};
+
+ vdd_usb_hub: regulator-vdd-usb-hub {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd_usb_hub";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vdd2_usb_hub: regulator-vdd2-usb-hub {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd2_usb_hub";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
};
&i2c1 { /* I2C_SCK C23/C24 - MIO from SOM */
@@ -154,6 +172,8 @@ hub_2_0: hub@1 {
peer-hub = <&hub_3_0>;
i2c-bus = <&hub>;
reset-gpios = <&slg_delay 0 10000 10000>;
+ vdd-supply = <&vdd_usb_hub>;
+ vdd2-supply = <&vdd2_usb_hub>;
};
/* 3.0 hub on port 2 */
--
2.43.0
prev parent reply other threads:[~2026-11-19 15:41 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-11-19 15:40 [PATCH 0/3] arm64: zynqmp: dts: Update USB hub description Michal Simek
2026-11-19 15:40 ` [PATCH 1/3] dt-bindings: usb: microchip,usb5744: Allow post-init-providers Michal Simek
2026-11-19 15:40 ` [PATCH 2/3] arm64: zynqmp: dts: Wire gpio-delay driver for USB hub reset Michal Simek
2026-11-19 15:40 ` Michal Simek [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=a807fea2b2af7c1b068ba375842efda44c0f0dac.1795102838.git.michal.simek@amd.com \
--to=michal.simek@amd.com \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=git@amd.com \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=monstr@monstr.eu \
--cc=robh@kernel.org \
--cc=suhan.sm@amd.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®