Re: [PATCH v7 7/8] arm64: dts: ti: k3-j721s2-main: Add PCIe device tree node

[Andrew Davis <afd@ti.com>]

On 11/22/22 4:16 AM, Matt Ranostay wrote:
> From: Aswath Govindraju <a-govindraju@ti.com>
> 
> Add PCIe1 RC device tree node for the single PCIe instance present on
> the j721s2.
> 
> Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
> Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
> Signed-off-by: Matt Ranostay <mranostay@ti.com>
> ---
>   arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi | 41 ++++++++++++++++++++++
>   1 file changed, 41 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
> index 2858ba589d54..27631ef32bf5 100644
> --- a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
> @@ -841,6 +841,47 @@ serdes0: serdes@5060000 {
>   		};
>   	};
>   
> +	pcie1_rc: pcie@2910000 {

NIT: Not sure we need to call this "_rc", and "1", 0 index these names for
consistency, "pcie0".

> +		compatible = "ti,j7200-pcie-host", "ti,j721e-pcie-host";
> +		reg = <0x00 0x02910000 0x00 0x1000>,
> +		      <0x00 0x02917000 0x00 0x400>,
> +		      <0x00 0x0d800000 0x00 0x00800000>,
> +		      <0x00 0x18000000 0x00 0x00001000>;
> +		reg-names = "intd_cfg", "user_cfg", "reg", "cfg";
> +		interrupt-names = "link_state";
> +		interrupts = <GIC_SPI 330 IRQ_TYPE_EDGE_RISING>;
> +		device_type = "pci";
> +		ti,syscon-pcie-ctrl = <&scm_conf 0x074>;
> +		max-link-speed = <3>;
> +		num-lanes = <4>;
> +		power-domains = <&k3_pds 276 TI_SCI_PD_EXCLUSIVE>;
> +		clocks = <&k3_clks 276 41>;
> +		clock-names = "fck";
> +		#address-cells = <3>;
> +		#size-cells = <2>;
> +		bus-range = <0x0 0xff>;
> +		vendor-id = <0x104c>;
> +		device-id = <0xb013>;
> +		msi-map = <0x0 &gic_its 0x0 0x10000>;
> +		dma-coherent;
> +		ranges = <0x01000000 0x0 0x18001000  0x00 0x18001000  0x0 0x0010000>,
> +			 <0x02000000 0x0 0x18011000  0x00 0x18011000  0x0 0x7fef000>;
> +		dma-ranges = <0x02000000 0x0 0x0 0x0 0x0 0x10000 0x0>;
> +		#interrupt-cells = <1>;

Is this node the interrupt controller or is it the "interrupt-controller"?
Actually, what is that node? I don't see it in the binding docs..

Andrew

> +		interrupt-map-mask = <0 0 0 7>;
> +		interrupt-map = <0 0 0 1 &pcie1_intc 0>, /* INT A */
> +				<0 0 0 2 &pcie1_intc 0>, /* INT B */
> +				<0 0 0 3 &pcie1_intc 0>, /* INT C */
> +				<0 0 0 4 &pcie1_intc 0>; /* INT D */
> +
> +		pcie1_intc: interrupt-controller {
> +			interrupt-controller;
> +			#interrupt-cells = <1>;
> +			interrupt-parent = <&gic500>;
> +			interrupts = <GIC_SPI 324 IRQ_TYPE_EDGE_RISING>;
> +		};
> +	};
> +
>   	main_mcan0: can@2701000 {
>   		compatible = "bosch,m_can";
>   		reg = <0x00 0x02701000 0x00 0x200>,