mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
From: Jonathan Santos <jonath4nns@gmail.com>
To: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Jonathan Santos <Jonathan.Santos@analog.com>,
	linux-iio@vger.kernel.org, devicetree@vger.kernel.org,
	linux-kernel@vger.kernel.org, linux-gpio@vger.kernel.org,
	andy@kernel.org, nuno.sa@analog.com,
	Michael.Hennerich@analog.com, marcelo.schmitt@analog.com,
	jic23@kernel.org, robh@kernel.org, krzk+dt@kernel.org,
	conor+dt@kernel.org, marcelo.schmitt1@gmail.com,
	linus.walleij@linaro.org, brgl@bgdev.pl, lgirdwood@gmail.com,
	broonie@kernel.org, dlechner@baylibre.com
Subject: Re: [PATCH v6 05/11] iio: adc: ad7768-1: add regulator to control VCM output
Date: Wed, 30 Apr 2025 20:24:06 -0300	[thread overview]
Message-ID: <aBKxFuKFYDWdDlh7@JSANTO12-L01.ad.analog.com> (raw)
In-Reply-To: <CAHp75Vciw_ivdKFsqo=FML64zUL_cDCzjuhmdVC3V_Whnatqwg@mail.gmail.com>

On 04/28, Andy Shevchenko wrote:
> On Mon, Apr 28, 2025 at 3:13 AM Jonathan Santos
> <Jonathan.Santos@analog.com> wrote:
> >
> > The VCM output voltage can be used as a common-mode voltage within the
> > amplifier preconditioning circuits external to the AD7768-1.
> >
> > This change allows the user to configure VCM output using the regulator
> > framework.
> 
> ...
> 
> >  #include <linux/gpio/consumer.h>
> >  #include <linux/kernel.h>
> >  #include <linux/module.h>
> > +#include <linux/of.h>
> 
> Why?
>

I was using of_match_ptr() before, but forgot to remove it, sorry.

> >  #include <linux/regmap.h>
> >  #include <linux/regulator/consumer.h>
> > +#include <linux/regulator/driver.h>
> 
> ...
> 
> > +static int ad7768_vcm_enable(struct regulator_dev *rdev)
> > +{
> > +       struct iio_dev *indio_dev = rdev_get_drvdata(rdev);
> > +       struct ad7768_state *st = iio_priv(indio_dev);
> > +       int ret, regval;
> 
> > +       if (!indio_dev)
> > +               return -EINVAL;
> 
> Isn't it a dead code? Or i.o.w. under which circumstances can this be true?
> Ditto for other functions with the same check.
> 

Yes, you're right. Since I defined the driver data below, there was no
need for the check.

> > +       if (!iio_device_claim_direct(indio_dev))
> > +               return -EBUSY;
> > +
> > +       /* To enable, set the last selected output */
> > +       regval = AD7768_REG_ANALOG2_VCM(st->vcm_output_sel + 1);
> > +       ret = regmap_update_bits(st->regmap, AD7768_REG_ANALOG2,
> > +                                AD7768_REG_ANALOG2_VCM_MSK, regval);
> > +       iio_device_release_direct(indio_dev);
> > +
> > +       return ret;
> > +}
> 
> ...
> 
> > +       return clamp(val, 1, (int)rdev->desc->n_voltages) - 1;
> 
> No explicit castings in min/max/clamp, please. This may lead to subtle
> mistakes. Also, don't forget to include minmax.h.
> 

Okay, thanks.

> -- 
> With Best Regards,
> Andy Shevchenko

  reply	other threads:[~2025-04-30 23:24 UTC|newest]

Thread overview: 36+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2025-04-28  0:11 [PATCH v6 00/11] iio: adc: ad7768-1: Add features, improvements, and fixes Jonathan Santos
2025-04-28  0:12 ` [PATCH v6 01/11] dt-bindings: trigger-source: add generic GPIO trigger source Jonathan Santos
2025-05-05 15:44   ` Jonathan Cameron
2025-05-05 15:56     ` David Lechner
2025-05-13  9:32   ` Linus Walleij
2025-04-28  0:12 ` [PATCH v6 02/11] dt-bindings: iio: adc: ad7768-1: add trigger-sources property Jonathan Santos
2025-04-30 18:46   ` David Lechner
2025-05-05 15:39   ` Jonathan Cameron
2025-05-06 19:16     ` Jonathan Santos
2025-05-07 19:50       ` Jonathan Cameron
2025-04-28  0:12 ` [PATCH v6 03/11] dt-bindings: iio: adc: ad7768-1: Document GPIO controller Jonathan Santos
2025-04-28  0:12 ` [PATCH v6 04/11] dt-bindings: iio: adc: ad7768-1: document regulator provider property Jonathan Santos
2025-04-28  0:13 ` [PATCH v6 05/11] iio: adc: ad7768-1: add regulator to control VCM output Jonathan Santos
2025-04-28  6:42   ` Andy Shevchenko
2025-04-30 23:24     ` Jonathan Santos [this message]
2025-04-30 18:43   ` David Lechner
2025-04-28  0:13 ` [PATCH v6 06/11] iio: adc: ad7768-1: Add GPIO controller support Jonathan Santos
2025-04-28  6:50   ` Andy Shevchenko
2025-04-30 23:37     ` Jonathan Santos
2025-04-28  0:13 ` [PATCH v6 07/11] iio: adc: ad7768-1: add multiple scan types to support 16-bits mode Jonathan Santos
2025-04-28  6:55   ` Andy Shevchenko
2025-05-05 15:52     ` Jonathan Cameron
2025-05-02 14:30   ` Marcelo Schmitt
2025-04-28  0:13 ` [PATCH v6 08/11] iio: adc: ad7768-1: add support for Synchronization over SPI Jonathan Santos
2025-04-28  7:04   ` Andy Shevchenko
2025-05-01  0:03     ` Jonathan Santos
2025-04-30 19:07   ` David Lechner
2025-05-05 15:59   ` Jonathan Cameron
2025-04-28  0:14 ` [PATCH v6 09/11] iio: adc: ad7768-1: replace manual attribute declaration Jonathan Santos
2025-04-28  7:10   ` Andy Shevchenko
2025-04-28  0:14 ` [PATCH v6 10/11] iio: adc: ad7768-1: add filter type and oversampling ratio attributes Jonathan Santos
2025-04-29 22:40   ` Andy Shevchenko
2025-05-05 16:09   ` Jonathan Cameron
2025-05-06 19:03     ` Jonathan Santos
2025-05-06 19:10       ` David Lechner
2025-04-28  0:14 ` [PATCH v6 11/11] iio: adc: ad7768-1: add low pass -3dB cutoff attribute Jonathan Santos

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=aBKxFuKFYDWdDlh7@JSANTO12-L01.ad.analog.com \
    --to=jonath4nns@gmail.com \
    --cc=CAHp75Vciw_ivdKFsqo=FML64zUL_cDCzjuhmdVC3V_Whnatqwg@mail.gmail.com \
    --cc=Jonathan.Santos@analog.com \
    --cc=Michael.Hennerich@analog.com \
    --cc=andy.shevchenko@gmail.com \
    --cc=andy@kernel.org \
    --cc=brgl@bgdev.pl \
    --cc=broonie@kernel.org \
    --cc=conor+dt@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=dlechner@baylibre.com \
    --cc=jic23@kernel.org \
    --cc=krzk+dt@kernel.org \
    --cc=lgirdwood@gmail.com \
    --cc=linus.walleij@linaro.org \
    --cc=linux-gpio@vger.kernel.org \
    --cc=linux-iio@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=marcelo.schmitt1@gmail.com \
    --cc=marcelo.schmitt@analog.com \
    --cc=nuno.sa@analog.com \
    --cc=robh@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®