From: Frank Li <Frank.li@nxp.com>
To: Manivannan Sadhasivam <manivannan.sadhasivam@oss.qualcomm.com>
Cc: "Rob Herring" <robh@kernel.org>,
"Greg Kroah-Hartman" <gregkh@linuxfoundation.org>,
"Jiri Slaby" <jirislaby@kernel.org>,
"Nathan Chancellor" <nathan@kernel.org>,
"Nicolas Schier" <nicolas.schier@linux.dev>,
"Hans de Goede" <hansg@kernel.org>,
"Ilpo Järvinen" <ilpo.jarvinen@linux.intel.com>,
"Mark Pearson" <mpearson-lenovo@squebb.ca>,
"Derek J. Clark" <derekjohn.clark@gmail.com>,
"Manivannan Sadhasivam" <mani@kernel.org>,
"Krzysztof Kozlowski" <krzk+dt@kernel.org>,
"Conor Dooley" <conor+dt@kernel.org>,
"Marcel Holtmann" <marcel@holtmann.org>,
"Luiz Augusto von Dentz" <luiz.dentz@gmail.com>,
"Bartosz Golaszewski" <brgl@bgdev.pl>,
linux-serial@vger.kernel.org, linux-kernel@vger.kernel.org,
linux-kbuild@vger.kernel.org,
platform-driver-x86@vger.kernel.org, linux-pci@vger.kernel.org,
devicetree@vger.kernel.org, linux-arm-msm@vger.kernel.org,
linux-bluetooth@vger.kernel.org, linux-pm@vger.kernel.org,
"Stephan Gerhold" <stephan.gerhold@linaro.org>,
"Dmitry Baryshkov" <dmitry.baryshkov@oss.qualcomm.com>
Subject: Re: [PATCH 7/9] dt-bindings: connector: Add PCIe M.2 Mechanical Key E connector
Date: Wed, 12 Nov 2025 12:11:56 -0500 [thread overview]
Message-ID: <aRS/3OTerCBGlmBm@lizhi-Precision-Tower-5810> (raw)
In-Reply-To: <20251112-pci-m2-e-v1-7-97413d6bf824@oss.qualcomm.com>
On Wed, Nov 12, 2025 at 08:15:19PM +0530, Manivannan Sadhasivam wrote:
> Add the devicetree binding for PCIe M.2 Mechanical Key E connector defined
> in the PCI Express M.2 Specification, r4.0, sec 5.1.2. This connector
> provides interfaces like PCIe or SDIO to attach the WiFi devices to the
> host machine, USB or UART+PCM interfaces to attach the Bluetooth (BT)
> devices along with additional interfaces like I2C for NFC solution. At any
> point of time, the connector can only support either PCIe or SDIO as the
> WiFi interface and USB or UART as the BT interface.
>
> The connector provides a primary power supply of 3.3v, along with an
> optional 1.8v VIO supply for the Adapter I/O buffer circuitry operating at
> 1.8v sideband signaling.
>
> The connector also supplies optional signals in the form of GPIOs for fine
> grained power management.
>
> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@oss.qualcomm.com>
> ---
> .../bindings/connector/pcie-m2-e-connector.yaml | 154 +++++++++++++++++++++
> MAINTAINERS | 1 +
> 2 files changed, 155 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/connector/pcie-m2-e-connector.yaml b/Documentation/devicetree/bindings/connector/pcie-m2-e-connector.yaml
> new file mode 100644
> index 0000000000000000000000000000000000000000..91cb56b1a75b7e3de3b9fe9a7537089f96875746
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/connector/pcie-m2-e-connector.yaml
> @@ -0,0 +1,154 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/connector/pcie-m2-e-connector.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: PCIe M.2 Mechanical Key E Connector
> +
> +maintainers:
> + - Manivannan Sadhasivam <manivannan.sadhasivam@oss.qualcomm.com>
> +
> +description:
> + A PCIe M.2 E connector node represents a physical PCIe M.2 Mechanical Key E
> + connector. Mechanical Key E connectors are used to connect Wireless
> + Connectivity devices including combinations of Wi-Fi, BT, NFC to the host
> + machine over interfaces like PCIe/SDIO, USB/UART+PCM, and I2C.
> +
> +properties:
> + compatible:
> + const: pcie-m2-e-connector
> +
> + vpcie3v3-supply:
> + description: A phandle to the regulator for 3.3v supply.
> +
> + vpcie1v8-supply:
> + description: A phandle to the regulator for VIO 1.8v supply.
> +
> + ports:
> + $ref: /schemas/graph.yaml#/properties/ports
> + description: OF graph bindings modeling the interfaces exposed on the
> + connector. Since a single connector can have multiple interfaces, every
> + interface has an assigned OF graph port number as described below.
> +
> + properties:
> + port@0:
> + $ref: /schemas/graph.yaml#/properties/port
> + description: PCIe/SDIO interface
PCIe and SDIO is difference signal at key E. why combine to one port? The
similar case is USB2.0/UART
> +
> + port@1:
> + $ref: /schemas/graph.yaml#/properties/port
> + description: USB 2.0/UART interface
> +
> + port@2:
> + $ref: /schemas/graph.yaml#/properties/port
> + description: PCM/I2S interface
> +
> + port@3:
> + $ref: /schemas/graph.yaml#/properties/port
> + description: I2C interface
> +
> + oneOf:
> + - required:
> + - port@0
> +
> + clocks:
> + description: 32.768 KHz Suspend Clock (SUSCLK) input from the host system to
> + the M.2 card. Refer, PCI Express M.2 Specification r4.0, sec 3.1.12.1 for
> + more details.
> + maxItems: 1
Do we need add pciref clock here?
> +
> + w_disable1-gpios:
use "-"
w-disable1-gpios
> + description: GPIO controlled connection to W_DISABLE1# signal. This signal
> + is used by the system to disable WiFi radio in the M.2 card. Refer, PCI
> + Express M.2 Specification r4.0, sec 3.1.12.3 for more details.
> + maxItems: 1
> +
> + w_disable2-gpios:
> + description: GPIO controlled connection to W_DISABLE2# signal. This signal
> + is used by the system to disable BT radio in the M.2 card. Refer, PCI
> + Express M.2 Specification r4.0, sec 3.1.12.3 for more details.
> + maxItems: 1
> +
> + led1-gpios:
> + description: GPIO controlled connection to LED_1# signal. This signal is
> + used by the M.2 card to indicate the card status via the system mounted
> + LED. Refer, PCI Express M.2 Specification r4.0, sec 3.1.12.2 for more
> + details.
> + maxItems: 1
> +
> + led2-gpios:
> + description: GPIO controlled connection to LED_2# signal. This signal is
> + used by the M.2 card to indicate the card status via the system mounted
> + LED. Refer, PCI Express M.2 Specification r4.0, sec 3.1.12.2 for more
> + details.
> + maxItems: 1
> +
> + viocfg-gpios:
> + description: GPIO controlled connection to IO voltage configuration
> + (VIO_CFG) signal. This signal is used by the M.2 card to indicate to the
> + host system that the card supports an independent IO voltage domain for
> + the sideband signals. Refer, PCI Express M.2 Specification r4.0, sec
> + 3.1.15.1 for more details.
> + maxItems: 1
> +
> + uim_power_src-gpios:
property use -
Frank
> + description: GPIO controlled connection to UIM_POWER_SRC signal. This signal
> + is used when the NFC solution is implemented and receives the power output
> + from WWAN_UIM_PWR signal of the another WWAN M.2 card. Refer, PCI Express
> + M.2 Specification r4.0, sec 3.1.11.1 for more details.
> + maxItems: 1
> +
> + uim_power_snk-gpios:
> + description: GPIO controlled connection to UIM_POWER_SNK signal. This signal
> + is used when the NFC solution is implemented and supplies power to the
> + Universal Integrated Circuit Card (UICC). Refer, PCI Express M.2
> + Specification r4.0, sec 3.1.11.2 for more details.
> + maxItems: 1
> +
> + uim_swp-gpios:
> + description: GPIO controlled connection to UIM_SWP signal. This signal is
> + used when the NFC solution is implemented and implements the Single Wire
> + Protocol (SWP) interface to the UICC. Refer, PCI Express M.2 Specification
> + r4.0, sec 3.1.11.3 for more details.
> + maxItems: i1
> +
> +required:
> + - compatible
> + - vpcie3v3-supply
> +
> +additionalProperties: false
> +
> +examples:
> + # PCI M.2 Key E connector for WLAN/BT with PCIe/UART interfaces
> + - |
> + #include <dt-bindings/gpio/gpio.h>
> +
> + connector {
> + compatible = "pcie-m2-e-connector";
> + vpcie3v3-supply = <&vreg_wcn_3p3>;
> + vpcie1v8-supply = <&vreg_l15b_1p8>;
> + w_disable1-gpios = <&tlmm 117 GPIO_ACTIVE_LOW>;
> + w_disable2-gpios = <&tlmm 116 GPIO_ACTIVE_LOW>;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> +
> + endpoint {
> + remote-endpoint = <&pcie4_port0_ep>;
> + };
> + };
> +
> + port@3 {
> + reg = <3>;
> +
> + endpoint {
> + remote-endpoint = <&uart14_ep>;
> + };
> + };
> + };
> + };
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 9b3f689d1f50c62afa3772a0c6802f99a98ac2de..f707f29d0a37f344d8dd061b7e49dbb807933c9f 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -20478,6 +20478,7 @@ PCIE M.2 POWER SEQUENCING
> M: Manivannan Sadhasivam <mani@kernel.org>
> L: linux-pci@vger.kernel.org
> S: Maintained
> +F: Documentation/devicetree/bindings/connector/pcie-m2-e-connector.yaml
> F: Documentation/devicetree/bindings/connector/pcie-m2-m-connector.yaml
> F: drivers/power/sequencing/pwrseq-pcie-m2.c
>
>
> --
> 2.48.1
>
next prev parent reply other threads:[~2025-11-12 17:12 UTC|newest]
Thread overview: 29+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-11-12 14:45 [PATCH 0/9] Add support for handling PCIe M.2 Key E connectors in devicetree Manivannan Sadhasivam via B4 Relay
2025-11-12 14:45 ` [PATCH 1/9] serdev: Convert to_serdev_device() and to_serdev_controller() helpers to macros Manivannan Sadhasivam via B4 Relay
2025-11-12 21:13 ` Rob Herring
2025-11-13 5:15 ` Manivannan Sadhasivam
2025-11-12 14:45 ` [PATCH 2/9] serdev: Add serdev device based driver match support Manivannan Sadhasivam via B4 Relay
2025-11-12 14:45 ` [PATCH 3/9] serdev: Allow passing the serdev device name to serdev_device_add() Manivannan Sadhasivam via B4 Relay
2025-11-18 9:41 ` Ilpo Järvinen
2025-11-12 14:45 ` [PATCH 4/9] serdev: Add an API to find the serdev controller associated with the devicetree node Manivannan Sadhasivam via B4 Relay
2025-11-12 14:45 ` [PATCH 5/9] serdev: Add modalias support for serdev client devices Manivannan Sadhasivam via B4 Relay
2025-11-12 14:45 ` [PATCH 6/9] serdev: Skip registering serdev devices from DT is external connector is used Manivannan Sadhasivam via B4 Relay
2025-11-18 13:03 ` Rob Herring
2025-11-19 13:32 ` Manivannan Sadhasivam
2025-11-20 16:22 ` Rob Herring
2025-11-20 16:54 ` Manivannan Sadhasivam
2025-11-12 14:45 ` [PATCH 7/9] dt-bindings: connector: Add PCIe M.2 Mechanical Key E connector Manivannan Sadhasivam via B4 Relay
2025-11-12 17:11 ` Frank Li [this message]
2025-11-13 5:00 ` Manivannan Sadhasivam
2025-11-19 23:59 ` Rob Herring
2025-11-20 12:57 ` Manivannan Sadhasivam
2025-11-12 20:08 ` Dmitry Baryshkov
2025-11-13 5:05 ` Manivannan Sadhasivam
2025-11-12 14:45 ` [PATCH 8/9] Bluetooth: hci_qca: Add support for WCN7850 PCIe M.2 card Manivannan Sadhasivam via B4 Relay
2025-11-18 14:29 ` Bartosz Golaszewski
2025-11-19 13:36 ` Manivannan Sadhasivam
2025-11-12 14:45 ` [PATCH 9/9] power: sequencing: pcie-m2: Add support for PCIe M.2 Key E connectors Manivannan Sadhasivam via B4 Relay
2025-11-19 13:28 ` Bartosz Golaszewski
2025-11-19 13:54 ` Manivannan Sadhasivam
2025-11-12 21:07 ` [PATCH 0/9] Add support for handling PCIe M.2 Key E connectors in devicetree Rob Herring
2025-11-13 5:13 ` Manivannan Sadhasivam
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=aRS/3OTerCBGlmBm@lizhi-Precision-Tower-5810 \
--to=frank.li@nxp.com \
--cc=brgl@bgdev.pl \
--cc=conor+dt@kernel.org \
--cc=derekjohn.clark@gmail.com \
--cc=devicetree@vger.kernel.org \
--cc=dmitry.baryshkov@oss.qualcomm.com \
--cc=gregkh@linuxfoundation.org \
--cc=hansg@kernel.org \
--cc=ilpo.jarvinen@linux.intel.com \
--cc=jirislaby@kernel.org \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-bluetooth@vger.kernel.org \
--cc=linux-kbuild@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pci@vger.kernel.org \
--cc=linux-pm@vger.kernel.org \
--cc=linux-serial@vger.kernel.org \
--cc=luiz.dentz@gmail.com \
--cc=mani@kernel.org \
--cc=manivannan.sadhasivam@oss.qualcomm.com \
--cc=marcel@holtmann.org \
--cc=mpearson-lenovo@squebb.ca \
--cc=nathan@kernel.org \
--cc=nicolas.schier@linux.dev \
--cc=platform-driver-x86@vger.kernel.org \
--cc=robh@kernel.org \
--cc=stephan.gerhold@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®