From: Paul Walmsley <paul.walmsley@sifive.com>
To: Anup Patel <Anup.Patel@wdc.com>
Cc: Palmer Dabbelt <palmer@sifive.com>,
Albert Ou <aou@eecs.berkeley.edu>,
Atish Patra <Atish.Patra@wdc.com>,
Christoph Hellwig <hch@infradead.org>,
Mike Rapoport <rppt@linux.ibm.com>,
"linux-riscv@lists.infradead.org"
<linux-riscv@lists.infradead.org>,
"linux-kernel@vger.kernel.org" <linux-kernel@vger.kernel.org>
Subject: Re: [PATCH v5 2/2] RISC-V: Setup initial page tables in two stages
Date: Wed, 10 Jul 2019 17:05:19 -0700 (PDT) [thread overview]
Message-ID: <alpine.DEB.2.21.9999.1907101703150.3422@viisi.sifive.com> (raw)
In-Reply-To: <20190607060049.29257-3-anup.patel@wdc.com>
On Fri, 7 Jun 2019, Anup Patel wrote:
> Currently, the setup_vm() does initial page table setup in one-shot
> very early before enabling MMU. Due to this, the setup_vm() has to map
> all possible kernel virtual addresses since it does not know size and
> location of RAM. This means we have kernel mappings for non-existent
> RAM and any buggy driver (or kernel) code doing out-of-bound access
> to RAM will not fault and cause underterministic behaviour.
>
> Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for
> RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e.
> MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e.
> 516 KB) of memory for initial page tables which is never freed. The
> memory required for initial page tables will further increase if
> we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000)
>
> This patch implements two-staged initial page table setup, as follows:
> 1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in
> a early page table (i.e. early_pg_dir). The early_pg_dir will be used
> only by boot HART so it can be freed as-part of init memory free-up.
> 2. Final (i.e. setup_vm_final()): This stage maps all possible RAM
> banks in the final page table (i.e. swapper_pg_dir). The boot HART
> will start using swapper_pg_dir at the end of setup_vm_final(). All
> non-boot HARTs directly use the swapper_pg_dir created by boot HART.
>
> We have following advantages with this new approach:
> 1. Kernel mappings for non-existent RAM don't exists anymore.
> 2. Memory consumed by initial page tables is now indpendent of the
> chosen PAGE_OFFSET.
> 3. Memory consumed by initial page tables on RV64 system is 2 pages
> (i.e. 8 KB) which has significantly reduced and these pages will be
> freed as-part of the init memory free-up.
>
> The patch also provides a foundation for implementing strict kernel
> mappings where we protect kernel text and rodata using PTE permissions.
>
> Suggested-by: Mike Rapoport <rppt@linux.ibm.com>
> Signed-off-by: Anup Patel <anup.patel@wdc.com>
Thanks, updated to apply and to fix a checkpatch warning, and queued.
This may not make it in for v5.3-rc1; if not, we'll submit it later.
- Paul
next prev parent reply other threads:[~2019-07-11 0:05 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-06-07 6:01 [PATCH v5 0/2] Two-stagged initial page table setup Anup Patel
2019-06-07 6:01 ` [PATCH v5 1/2] RISC-V: Fix memory reservation in setup_bootmem() Anup Patel
2019-06-28 20:59 ` Paul Walmsley
2019-06-07 6:01 ` [PATCH v5 2/2] RISC-V: Setup initial page tables in two stages Anup Patel
2019-07-11 0:05 ` Paul Walmsley [this message]
2019-08-15 18:57 ` Alistair Francis
2019-08-15 19:07 ` David Abdurachmanov
2019-08-15 20:25 ` Alistair Francis
2019-08-15 20:29 ` Paul Walmsley
2019-08-15 21:32 ` Alistair Francis
2019-08-16 1:05 ` Anup Patel
2019-06-22 4:13 ` [PATCH v5 0/2] Two-stagged initial page table setup Anup Patel
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=alpine.DEB.2.21.9999.1907101703150.3422@viisi.sifive.com \
--to=paul.walmsley@sifive.com \
--cc=Anup.Patel@wdc.com \
--cc=Atish.Patra@wdc.com \
--cc=aou@eecs.berkeley.edu \
--cc=hch@infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-riscv@lists.infradead.org \
--cc=palmer@sifive.com \
--cc=rppt@linux.ibm.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®