Re: [PATCH 2/3] dt-bindings: media: i2c: Add vision-components,mipi-module-controller

[Richard Leitner <richard.leitner@linux.dev>]

Hi Krzysztof,

thanks for the review!

On Wed, Sep 16, 2026 at 09:00:46AM +0200, Krzysztof Kozlowski wrote:
> On Tue, Sep 15, 2026 at 10:20:24PM +0200, Richard Leitner wrote:
> > Add bindings for the Vision Components MIPI Camera Module Controller.
> > 
> > Signed-off-by: Richard Leitner <richard.leitner@linux.dev>
> > ---
> >  .../vision-components,mipi-module-controller.yaml  | 92 ++++++++++++++++++++++
> >  MAINTAINERS                                        |  7 ++
> >  2 files changed, 99 insertions(+)
> 
> This fails tests, so a very brief review / a few comments:

Mea culpa, I simply failed to run the dtb check before submitting. Sorry.
Will not happen again.

> 
> > 
> > diff --git a/Documentation/devicetree/bindings/media/i2c/vision-components,mipi-module-controller.yaml b/Documentation/devicetree/bindings/media/i2c/vision-components,mipi-module-controller.yaml
> > new file mode 100644
> > index 0000000000000..2a031aea68457
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/media/i2c/vision-components,mipi-module-controller.yaml
> > @@ -0,0 +1,92 @@
> > +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> > +%YAML 1.2
> > +---
> > +$id: http://devicetree.org/schemas/media/i2c/vision-components,mipi-module-controller.yaml#
> > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > +
> > +title: Vision Components MIPI Camera Module Controller
> > +
> > +maintainers:
> > +  - Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> > +  - Richard Leitner <richard.leitner@linux.dev>
> > +
> > +description: |-
> > +  The MIPI camera module controller is an FPGA-based, I2C-accessible system
> > +  controller found on MIPI camera modules from Vision Components. It abstracts
> > +  the camera sensor behind a unified register interface, and controls and
> > +  sequences the on-board power supplies and clocks.
> > +
> > +  The camera sensor abstraction is optional. The controller exposes a tunneled
> > +  downstream I2C bus used by the attached image sensor. The controller node
> > +  acts as the upstream device on the host bus, while child node below the
> > +  controller represent the sensor device reachable through the tunnel.
> > +
> > +properties:
> > +  compatible:
> > +    const: vision-components,mipi-module-controller
> 
> There is no model name, no version, nothing identifying it better?
> Compatible must be specific to the device (see also writing bindings).

There is one FPGA implemenation for all Vision Components MIPI camera
modules AFAICT. So I have no idea how it could be more specific, TBH...

Adding the FPGA hardware model/type is wrong IMHO as it depends on its
configuration/firmware, not the hw.

There are different versions of the configuration/firmware. But I think
this is also not the correct way to distinguish those, or is it?

According to their homepage the vendor calls those modules simply
"VC MIPI" modules, which implies this FPGA controller is available on it.
So maybe "vision-components,vc-mipi-controller" would be a better fit?

Do you have any ideas/feedback on how improve this name?

> 
> > +
> > +  reg:
> > +    maxItems: 1
> > +
> > +  '#clock-cells':
> > +    const: 0
> > +
> > +  clock-frequency:
> > +    description: Frequency of the sensor clock provided by the module
> 
> Drop, implied by the compatible
> 

Do you mean dropping the whole property, or just the "description"?

> > +
> > +  vcc-supply:
> > +    description: Power supply of the module (3.3V)
> > +
> > +  '#address-cells':
> > +    const: 1
> > +
> > +  '#size-cells':
> > +    const: 0
> 
> No children allowed, so why these two?

Based on your and the bot feedback I would suggest for v2 to change this
"generic i2c bus" to a simple "i2c-tunnel" property which has
"$ref: /schemas/i2c/i2c-controller.yaml".

This would better reflect the actual hardware, as there is only this one,
in firmware hard-coded I2C downstream bus.

Would this be a sane approach?

> 
> > +
> > +required:
> > +  - compatible
> > +  - reg
> > +  - '#clock-cells'
> > +  - clock-frequency
> > +  - vcc-supply
> > +  - '#address-cells'
> > +  - '#size-cells'
> > +
> > +unevaluatedProperties: false
> 
> additionalProperties instead, see writing bindings or writing schema.
> Unless you miss here some other schema $ref.
> 
> > +
> > +examples:
> > +  - |
> > +    i2c {
> > +        #address-cells = <1>;
> > +        #size-cells = <0>;
> > +
> > +        vc_mipi_ctrl: controller@10 {
> > +            compatible = "vision-components,mipi-module-controller";
> > +            reg = <0x10>;
> > +            #clock-cells = <0>;
> > +            clock-frequency = <37125000>;
> > +            vcc-supply = <&cam_3v3>;
> > +
> > +            #address-cells = <1>;
> > +            #size-cells = <0>;
> > +
> > +            i2c@0 {
> > +                #address-cells = <1>;
> > +                #size-cells = <0>;
> > +
> > +                vc_mipi_sensor: camera@60 {
> > +                    compatible = "ovti,ov9281";
> > +                    reg = <0x60>;
> 
> Why having the child abstraction if it is completely abstracted? I don't
> fully get the explanation from description. Completely optional means no
> benefits, no point in it, no?

I will try to improve the description. The idea behind this device
driver/devicetree node is to not rely on the sensor abstraction from
vision components, but to use the upstream sensor specific driver.

As the tunneled downstream i2c bus needs quirks applied this is modeled
as a separate bus.

Previous discussions on this approach are available at:
	https://lore.kernel.org/lkml/20260728092856.GB1494774@killaraus.ideasonboard.com/

Thanks again for your review Krzysztof!

regards;rl

> 
> Best regards,
> Krzysztof
>