mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
From: "Nuno Sá" <nuno.sa@analog.com>
To: Janani Sunil <janani.sunil@analog.com>
Cc: Michael Hennerich <Michael.Hennerich@analog.com>,
	Jonathan Cameron <jic23@kernel.org>,
	David Lechner <dlechner@baylibre.com>,
	Andy Shevchenko <andy@kernel.org>,
	linux-iio@vger.kernel.org, linux@analog.com,
	linux-kernel@vger.kernel.org, jan.sun97@gmail.com,
	Andy Shevchenko <andriy.shevchenko@intel.com>
Subject: Re: [PATCH] iio: dac: ad5529r: Clean up definitions and regmap configuration
Date: Mon, 12 Oct 2026 15:45:47 +0100	[thread overview]
Message-ID: <aszyX_e44Dp2MSln@nsa> (raw)
In-Reply-To: <20261008-ad5529r-review-followup-v1-1-84a98e0e27eb@analog.com>

On Thu, Oct 08, 2026 at 11:19:15AM +0200, Janani Sunil wrote:
> Use fixed width register literals matching the device's register address
> width. Rely on SPI regmap's default read flag instead of specifying the
> same value explicitly, and remove parentheses around the channel
> initializer.
> 
> Suggested-by: Andy Shevchenko <andriy.shevchenko@intel.com>
> Signed-off-by: Janani Sunil <janani.sunil@analog.com>
> ---
> The AD5529R driver is already queued in the IIO tree. This patch follows
> up on the remaining review comments from Andy Shevchenko:
> 
> https://lore.kernel.org/r/arzTnOTaL97GudZM@ashevche-desk.local/
> ---

Seems like there are some other things recommended by Andy. But those
can be different patches. Hence for this one:

Reviewed-by: Nuno Sá <nuno.sa@analog.com>

>  drivers/iio/dac/ad5529r.c | 29 +++++++++++++----------------
>  1 file changed, 13 insertions(+), 16 deletions(-)
> 
> diff --git a/drivers/iio/dac/ad5529r.c b/drivers/iio/dac/ad5529r.c
> index 8154b87ff831..04bb02af9612 100644
> --- a/drivers/iio/dac/ad5529r.c
> +++ b/drivers/iio/dac/ad5529r.c
> @@ -24,19 +24,19 @@
>  
>  #include <linux/iio/iio.h>
>  
> -#define AD5529R_REG_INTERFACE_CONFIG_A		0x00
> +#define AD5529R_REG_INTERFACE_CONFIG_A		0x000
>  #define   AD5529R_INTERFACE_CONFIG_A_SW_RESET	(BIT(7) | BIT(0))
>  #define   AD5529R_INTERFACE_CONFIG_A_ADDR_ASCENSION	BIT(5)
>  #define   AD5529R_INTERFACE_CONFIG_A_SDO_ENABLE	BIT(4)
> -#define AD5529R_REG_DEVICE_CONFIG		0x02
> -#define AD5529R_REG_CHIP_GRADE			0x06
> -#define AD5529R_REG_SCRATCH_PAD			0x0A
> -#define AD5529R_REG_SPI_REVISION		0x0B
> -#define AD5529R_REG_VENDOR_H			0x0D
> -#define AD5529R_REG_STREAM_MODE			0x0E
> -#define AD5529R_REG_INTERFACE_STATUS_A		0x11
> -#define AD5529R_REG_MULTI_DAC_CH_SEL		0x14
> -#define AD5529R_REG_OUT_RANGE_BASE		0x3C
> +#define AD5529R_REG_DEVICE_CONFIG		0x002
> +#define AD5529R_REG_CHIP_GRADE			0x006
> +#define AD5529R_REG_SCRATCH_PAD			0x00A
> +#define AD5529R_REG_SPI_REVISION		0x00B
> +#define AD5529R_REG_VENDOR_H			0x00D
> +#define AD5529R_REG_STREAM_MODE			0x00E
> +#define AD5529R_REG_INTERFACE_STATUS_A		0x011
> +#define AD5529R_REG_MULTI_DAC_CH_SEL		0x014
> +#define AD5529R_REG_OUT_RANGE_BASE		0x03C
>  #define AD5529R_REG_OUT_RANGE(ch)		(AD5529R_REG_OUT_RANGE_BASE + (ch) * 2)
>  #define AD5529R_REG_DAC_INPUT_A_BASE		0x148
>  #define AD5529R_REG_DAC_INPUT_A(ch)		(AD5529R_REG_DAC_INPUT_A_BASE + (ch) * 2)
> @@ -50,9 +50,8 @@
>  #define AD5529R_REG_MULTI_DAC_HOTPATH_SW_LDAC	0x1A8
>  
>  #define AD5529R_MAX_REGISTER			0x232
> -#define AD5529R_8BIT_REG_MAX			0x13
> +#define AD5529R_8BIT_REG_MAX			0x013
>  #define AD5529R_MAX_CHANNELS			16
> -#define AD5529R_SPI_READ_FLAG			0x80
>  #define AD5529R_ADDR_SHIFT			12
>  
>  struct ad5529r_model_data {
> @@ -60,7 +59,7 @@ struct ad5529r_model_data {
>  	unsigned int resolution;
>  };
>  
> -#define AD5529R_DAC_CHANNEL(chan) ((struct iio_chan_spec) {		\
> +#define AD5529R_DAC_CHANNEL(chan) (struct iio_chan_spec) {		\
>  	.type = IIO_VOLTAGE,						\
>  	.indexed = 1,							\
>  	.output = 1,							\
> @@ -68,7 +67,7 @@ struct ad5529r_model_data {
>  	.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |			\
>  			      BIT(IIO_CHAN_INFO_SCALE) |		\
>  			      BIT(IIO_CHAN_INFO_OFFSET),		\
> -})
> +	}
>  
>  static const char * const ad5529r_supply_names[] = {
>  	"vdd-io",
> @@ -433,7 +432,6 @@ static int ad5529r_probe(struct spi_device *spi)
>  		.reg_bits = 16,
>  		.val_bits = 8,
>  		.max_register = AD5529R_8BIT_REG_MAX,
> -		.read_flag_mask = AD5529R_SPI_READ_FLAG,
>  		.rd_table = &ad5529r_8bit_readable_table,
>  		.wr_table = &ad5529r_8bit_writeable_table,
>  		.reg_base = dev_addr << AD5529R_ADDR_SHIFT,
> @@ -443,7 +441,6 @@ static int ad5529r_probe(struct spi_device *spi)
>  		.reg_bits = 16,
>  		.val_bits = 16,
>  		.max_register = AD5529R_MAX_REGISTER,
> -		.read_flag_mask = AD5529R_SPI_READ_FLAG,
>  		.val_format_endian = REGMAP_ENDIAN_LITTLE,
>  		.rd_table = &ad5529r_16bit_readable_table,
>  		.wr_table = &ad5529r_16bit_writeable_table,
> 
> ---
> base-commit: a3b3580713f3ac5a32dc2874ee546828977a1d68
> change-id: 20261006-ad5529r-review-followup-22c8547c5b65
> 
> Best regards,
> -- 
> Janani Sunil <janani.sunil@analog.com>
> 

  reply	other threads:[~2026-10-12 14:44 UTC|newest]

Thread overview: 3+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2026-10-08  9:19 Janani Sunil
2026-10-12 14:45 ` Nuno Sá [this message]
2026-10-12 21:19 ` Andy Shevchenko

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=aszyX_e44Dp2MSln@nsa \
    --to=nuno.sa@analog.com \
    --cc=Michael.Hennerich@analog.com \
    --cc=andriy.shevchenko@intel.com \
    --cc=andy@kernel.org \
    --cc=dlechner@baylibre.com \
    --cc=jan.sun97@gmail.com \
    --cc=janani.sunil@analog.com \
    --cc=jic23@kernel.org \
    --cc=linux-iio@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux@analog.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®