From: Frank Li <Frank.li@oss.nxp.com>
To: Haoning Cheng <Haoning.CHENG@cn.bosch.com>
Cc: Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>,
Shawn Guo <shawnguo@kernel.org>, Frank Li <Frank.Li@nxp.com>,
Sascha Hauer <s.hauer@pengutronix.de>,
Pengutronix Kernel Team <kernel@pengutronix.de>,
Fabio Estevam <festevam@gmail.com>,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
imx@lists.linux.dev, linux-arm-kernel@lists.infradead.org,
Leonhard Hesse <leonhard.hesse@bshg.com>
Subject: Re: [PATCH v2 3/8] ARM: dts: imx6ulz: Adjust BSH SMM-M2 Wi-Fi and Bluetooth pin settings
Date: Fri, 6 Nov 2026 10:47:25 -0600 [thread overview]
Message-ID: <au4EnWiIRT4xoT-6@SMW015318> (raw)
In-Reply-To: <20261105-add-bsh-smm-m2-v2-3-fb5ffc7da486@cn.bosch.com>
On Thu, Nov 05, 2026 at 10:41:17AM +0800, Haoning Cheng wrote:
> From: Leonhard Hesse <leonhard.hesse@bshg.com>
>
> Adjustment of wifi and bluetooth REG_ON pin settings.
> Tests have shown that minor changes in drive strength, slew rate
> and speed resulted in the best performance.
It is just GPIO, why strength, slew rate impact performace?
Frank
>
> Signed-off-by: Leonhard Hesse <leonhard.hesse@bshg.com>
> Signed-off-by: Haoning Cheng <Haoning.CHENG@cn.bosch.com>
> ---
> arch/arm/boot/dts/nxp/imx/imx6ulz-bsh-smm-m2.dts | 4 ++--
> 1 file changed, 2 insertions(+), 2 deletions(-)
>
> diff --git a/arch/arm/boot/dts/nxp/imx/imx6ulz-bsh-smm-m2.dts b/arch/arm/boot/dts/nxp/imx/imx6ulz-bsh-smm-m2.dts
> index aac211a9f9eb..dabe17222f13 100644
> --- a/arch/arm/boot/dts/nxp/imx/imx6ulz-bsh-smm-m2.dts
> +++ b/arch/arm/boot/dts/nxp/imx/imx6ulz-bsh-smm-m2.dts
> @@ -125,7 +125,7 @@ MX6UL_PAD_UART3_TX_DATA__UART3_DCE_TX 0x1b0b1
> MX6UL_PAD_UART3_RX_DATA__UART3_DCE_RX 0x1b099
> MX6UL_PAD_UART3_RTS_B__UART3_DCE_RTS 0x1b0b1
> MX6UL_PAD_UART3_CTS_B__UART3_DCE_CTS 0x1b099
> - MX6UL_PAD_GPIO1_IO01__GPIO1_IO01 0x79 /* BT_REG_ON */
> + MX6UL_PAD_GPIO1_IO01__GPIO1_IO01 0x100b1 /* BT_REG_ON */
> MX6UL_PAD_SD1_CLK__GPIO2_IO17 0x100b1 /* BT_DEV_WAKE out */
> MX6UL_PAD_ENET2_TX_EN__GPIO2_IO13 0x1b0b0 /* BT_HOST_WAKE in */
> >;
> @@ -146,7 +146,7 @@ MX6UL_PAD_CSI_DATA00__USDHC2_DATA0 0x17059
> MX6UL_PAD_CSI_DATA01__USDHC2_DATA1 0x17059
> MX6UL_PAD_CSI_DATA02__USDHC2_DATA2 0x17059
> MX6UL_PAD_CSI_DATA03__USDHC2_DATA3 0x17059
> - MX6UL_PAD_SD1_DATA3__GPIO2_IO21 0x79 /* WL_REG_ON */
> + MX6UL_PAD_SD1_DATA3__GPIO2_IO21 0x3029 /* WL_REG_ON */
> MX6UL_PAD_UART2_CTS_B__GPIO1_IO22 0x100b1 /* WL_DEV_WAKE - WiFi_GPIO_4 - WiFi FW UART */
> MX6UL_PAD_UART1_CTS_B__GPIO1_IO18 0x1b0b1 /* WL_HOST_WAKE - WIFI_GPIO_0 - OOB IRQ */
> MX6UL_PAD_ENET1_RX_EN__OSC32K_32K_OUT 0x4001b031 /* OSC 32Khz wifi clk in */
>
> --
> 2.43.0
>
>
next prev parent reply other threads:[~2026-11-06 16:47 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-11-05 2:41 [PATCH v2 0/8] Update BSH SystemMaster device trees and add SMM-M2B support Haoning Cheng
2026-11-05 2:41 ` [PATCH v2 1/8] dt-bindings: arm: fsl: Add BSH SMM-M2B board Haoning Cheng
2026-11-06 12:51 ` Krzysztof Kozlowski
2026-11-05 2:41 ` [PATCH v2 2/8] dts: imx: Use minimum NAND ECC strength on BSH boards Haoning Cheng
2026-11-05 2:41 ` [PATCH v2 3/8] ARM: dts: imx6ulz: Adjust BSH SMM-M2 Wi-Fi and Bluetooth pin settings Haoning Cheng
2026-11-06 16:47 ` Frank Li [this message]
2026-11-05 2:41 ` [PATCH v2 4/8] ARM: dts: imx6ulz: Fix BSH SMM-M2 WLAN host wake configuration Haoning Cheng
2026-11-06 16:50 ` Frank Li
2026-11-05 2:41 ` [PATCH v2 5/8] ARM: dts: imx6ulz: Factor out BSH SMM-M2 common device tree Haoning Cheng
2026-11-05 2:41 ` [PATCH v2 6/8] ARM: dts: imx6ulz: Add BSH SMM-M2B board support Haoning Cheng
2026-11-05 2:41 ` [PATCH v2 7/8] ARM: dts: imx6ulz: Configure UART2 pins on BSH SMM-M2 variants Haoning Cheng
2026-11-05 2:41 ` [PATCH v2 8/8] dts: imx: Enable USB OTG mode on BSH SMM-M2 and SMM-S2 Haoning Cheng
2026-11-06 16:44 ` Frank Li
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=au4EnWiIRT4xoT-6@SMW015318 \
--to=frank.li@oss.nxp.com \
--cc=Frank.Li@nxp.com \
--cc=Haoning.CHENG@cn.bosch.com \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=festevam@gmail.com \
--cc=imx@lists.linux.dev \
--cc=kernel@pengutronix.de \
--cc=krzk+dt@kernel.org \
--cc=leonhard.hesse@bshg.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robh@kernel.org \
--cc=s.hauer@pengutronix.de \
--cc=shawnguo@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®