From: Frank Li <Frank.li@oss.nxp.com>
To: James Hilliard <james.hilliard1@gmail.com>
Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>,
Vinod Koul <vkoul@kernel.org>, Frank Li <Frank.Li@kernel.org>,
Sergey Khimich <serghox@gmail.com>,
Andy Shevchenko <andriy.shevchenko@linux.intel.com>,
Sia Jee Heng <jee.heng.sia@intel.com>,
Baruch Siach <baruch@tkos.co.il>,
Mitch Barnett <mitch@accuratesound.ca>,
dmaengine@vger.kernel.org, linux-kernel@vger.kernel.org,
stable@vger.kernel.org
Subject: Re: [PATCH v8 2/9] dmaengine: dw-axi-dmac: poll the correct enable bit during termination
Date: Thu, 19 Nov 2026 10:17:07 -0600 [thread overview]
Message-ID: <av8hAwftf06wtsE_@SMW015318> (raw)
In-Reply-To: <20261119-submit-dw-axi-dma-stop-pause-v1-v8-2-f8e7fe60594c@gmail.com>
On Thu, Nov 19, 2026 at 09:00:57AM -0700, James Hilliard wrote:
> For channels 16 through 31, the channel enable bits occupy bits 32 through
> 47 of the extended DMAC_CHEN register. dma_chan_terminate_all() only reads
> the low word and tests BIT(chan->id), so it can conclude that an upper-bank
> channel has stopped while its actual enable bit remains set. Descriptors
> can then be freed while hardware still owns them.
>
> Poll axi_chan_is_hw_enable(), which already handles both register banks
> and the smaller channel layouts, instead of constructing another mask.
>
> Fixes: 495e18b16e3d ("dmaengine: dw-axi-dmac: Add support DMAX_NUM_CHANNELS > 16")
> Cc: stable@vger.kernel.org
> Signed-off-by: James Hilliard <james.hilliard1@gmail.com>
> ---
Reviewed-by: Frank Li <Frank.Li@nxp.com>
> drivers/dma/dw-axi-dmac/dw-axi-dmac-platform.c | 11 ++++++-----
> 1 file changed, 6 insertions(+), 5 deletions(-)
>
> diff --git a/drivers/dma/dw-axi-dmac/dw-axi-dmac-platform.c b/drivers/dma/dw-axi-dmac/dw-axi-dmac-platform.c
> index 6dae63024721..f17a71183050 100644
> --- a/drivers/dma/dw-axi-dmac/dw-axi-dmac-platform.c
> +++ b/drivers/dma/dw-axi-dmac/dw-axi-dmac-platform.c
> @@ -28,6 +28,7 @@
> #include <linux/property.h>
> #include <linux/reset.h>
> #include <linux/slab.h>
> +#include <linux/time64.h>
> #include <linux/types.h>
>
> #include "dw-axi-dmac.h"
> @@ -1179,17 +1180,17 @@ static irqreturn_t dw_axi_dma_interrupt(int irq, void *dev_id)
> static int dma_chan_terminate_all(struct dma_chan *dchan)
> {
> struct axi_dma_chan *chan = dchan_to_axi_dma_chan(dchan);
> - u32 chan_active = BIT(chan->id) << DMAC_CHAN_EN_SHIFT;
> unsigned long flags;
> - u32 val;
> + bool enabled;
> int ret;
> LIST_HEAD(head);
>
> axi_chan_disable(chan);
>
> - ret = readl_poll_timeout_atomic(chan->chip->regs + DMAC_CHEN, val,
> - !(val & chan_active), 1000, 50000);
> - if (ret == -ETIMEDOUT)
> + ret = read_poll_timeout_atomic(axi_chan_is_hw_enable, enabled, !enabled,
> + 1 * USEC_PER_MSEC, 50 * USEC_PER_MSEC,
> + false, chan);
> + if (ret)
> dev_warn(dmaengine_chan_dev(dchan),
> "%s failed to stop\n", axi_chan_name(chan));
>
>
> --
> 2.53.0
>
next prev parent reply other threads:[~2026-11-19 16:17 UTC|newest]
Thread overview: 22+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-11-19 16:00 [PATCH v8 0/9] dmaengine: dw-axi-dmac: fix termination and pause acknowledgment James Hilliard
2026-11-19 16:00 ` [PATCH v8 1/9] dmaengine: dw-axi-dmac: keep cyclic mode in the descriptor James Hilliard
2026-11-19 16:00 ` [PATCH v8 2/9] dmaengine: dw-axi-dmac: poll the correct enable bit during termination James Hilliard
2026-11-19 16:17 ` Frank Li [this message]
2026-11-19 16:00 ` [PATCH v8 3/9] dmaengine: dw-axi-dmac: retain descriptors when termination times out James Hilliard
2026-11-19 16:18 ` Frank Li
2026-11-19 16:00 ` [PATCH v8 4/9] dmaengine: dw-axi-dmac: use atomic polling for suspend acknowledgment James Hilliard
2026-11-19 16:19 ` Frank Li
2026-11-19 16:01 ` [PATCH v8 5/9] dmaengine: dw-axi-dmac: preserve pending pause requests James Hilliard
2026-11-19 16:27 ` Frank Li
2026-11-19 17:07 ` James Hilliard
2026-11-19 16:01 ` [PATCH v8 6/9] dmaengine: dw-axi-dmac: retain descriptors until callbacks drain James Hilliard
2026-11-19 16:41 ` Frank Li
2026-11-19 17:07 ` James Hilliard
2026-11-19 16:01 ` [PATCH v8 7/9] dmaengine: dw-axi-dmac: serialize interrupt status with channel reuse James Hilliard
2026-11-19 16:44 ` Frank Li
2026-11-19 17:10 ` James Hilliard
2026-11-19 16:01 ` [PATCH v8 8/9] dmaengine: dw-axi-dmac: require an IRQ before registering the controller James Hilliard
2026-11-19 16:47 ` Frank Li
2026-11-19 16:01 ` [PATCH v8 9/9] dmaengine: dw-axi-dmac: guard shared IRQs across the controller lifetime James Hilliard
2026-11-19 16:50 ` Frank Li
2026-11-19 17:11 ` James Hilliard
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=av8hAwftf06wtsE_@SMW015318 \
--to=frank.li@oss.nxp.com \
--cc=Eugeniy.Paltsev@synopsys.com \
--cc=Frank.Li@kernel.org \
--cc=andriy.shevchenko@linux.intel.com \
--cc=baruch@tkos.co.il \
--cc=dmaengine@vger.kernel.org \
--cc=james.hilliard1@gmail.com \
--cc=jee.heng.sia@intel.com \
--cc=linux-kernel@vger.kernel.org \
--cc=mitch@accuratesound.ca \
--cc=serghox@gmail.com \
--cc=stable@vger.kernel.org \
--cc=vkoul@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®