mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
From: Hangbin Liu <hangbin.liu@linux.dev>
To: Gopal Malaviya <gopalmalaviya53@gmail.com>
Cc: netdev@vger.kernel.org, "David S . Miller" <davem@davemloft.net>,
	Eric Dumazet <edumazet@kernel.org>,
	Jakub Kicinski <kuba@kernel.org>, Paolo Abeni <pabeni@redhat.com>,
	Simon Horman <horms@kernel.org>, Jonathan Corbet <corbet@lwn.net>,
	Shuah Khan <skhan@linuxfoundation.org>,
	Randy Dunlap <rdunlap@infradead.org>,
	linux-doc@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: Re: [PATCH net-next] docs: net: fix outdated default values of four sysctls
Date: Mon, 9 Nov 2026 08:56:48 +0800	[thread overview]
Message-ID: <avEZlo0YVa5v3hu-@fedora> (raw)
In-Reply-To: <20261108061746.32090-1-gopalmalaviya53@gmail.com>

On Sun, Nov 08, 2026 at 06:17:46AM +0000, Gopal Malaviya wrote:
> The defaults documented in ip-sysctl.rst for four sysctls differ from
> the values the kernel actually uses:
> 
>   sysctl                  documented  actual
>   cipso_rbm_strictvalid   0           1
>   flowlabel_state_ranges  1           0
>   router_solicitations    3           -1
>   regen_max_retry         5           3
> 
> Each one went stale when the code changed and the documentation was not
> updated, or was wrong from the start:
> 
> - cipso_v4_rbm_strictvalid has been initialised to 1 since CIPSO was
>   merged, while the documentation added with it said 0.
> - Commit be26849bfb6f ("ipv6: Disable flowlabel state ranges by
>   default") changed the default of flowlabel_state_ranges to 0.
> - Commit bd11f0741fa5 ("ipv6 addrconf: implement RFC7559 router
>   solicitation backoff") changed MAX_RTR_SOLICITATIONS from 3 to -1,
>   meaning that router solicitations are sent without a limit. The
>   documentation was not updated and never mentioned -1.
> - Commit 76f793e3a471 ("ipv6: updates to privacy addresses per RFC
>   4941.") changed REGEN_MAX_RETRY from 5 to 3.
> 
> Update the four defaults and note that -1 means no limit for
> router_solicitations.
> 
> The mismatches were found with the help of an AI assistant (Claude),
> which compared the defaults documented in ip-sysctl.rst with the values
> under /proc/sys/net on a running kernel and with the initial values in
> the source. I confirmed each value with sysctl on a running kernel and
> against the net-next source and the commits below. The commit message
> was drafted with the same assistance.
> 
> Tested by building the networking documentation with
> "make SPHINXDIRS=networking htmldocs": the change adds no warnings and
> the four defaults render as updated.
> 
> Fixes: 8802f616f6de ("[NetLabel]: documentation")
> Fixes: be26849bfb6f ("ipv6: Disable flowlabel state ranges by default")
> Fixes: bd11f0741fa5 ("ipv6 addrconf: implement RFC7559 router solicitation backoff")
> Fixes: 76f793e3a471 ("ipv6: updates to privacy addresses per RFC 4941.")
> Signed-off-by: Gopal Malaviya <gopalmalaviya53@gmail.com>
> ---
>  Documentation/networking/ip-sysctl.rst | 10 +++++-----
>  1 file changed, 5 insertions(+), 5 deletions(-)
> 
> diff --git a/Documentation/networking/ip-sysctl.rst b/Documentation/networking/ip-sysctl.rst
> index bc22400b53..0b7bfbd98a 100644
> --- a/Documentation/networking/ip-sysctl.rst
> +++ b/Documentation/networking/ip-sysctl.rst
> @@ -1587,7 +1587,7 @@ cipso_rbm_strictvalid - BOOLEAN
>  	- 0 (disabled)
>  	- 1 (enabled)
>  
> -	Default: 0 (disabled)
> +	Default: 1 (enabled)
>  
>  IP Variables
>  ============
> @@ -2418,7 +2418,7 @@ flowlabel_state_ranges - BOOLEAN
>  	- 0 (disabled)
>  	- 1 (enabled)
>  
> -	Default: 1 (enabled)
> +	Default: 0 (disabled)
>  
>  
>  flowlabel_reflect - INTEGER
> @@ -2956,9 +2956,9 @@ router_solicitation_interval - INTEGER
>  
>  router_solicitations - INTEGER
>  	Number of Router Solicitations to send until assuming no
> -	routers are present.
> +	routers are present. A value of -1 means no limit.
>  
> -	Default: 3
> +	Default: -1
>  
>  use_oif_addrs_only - BOOLEAN
>  	When enabled, the candidate source addresses for destinations
> @@ -3034,7 +3034,7 @@ regen_max_retry - INTEGER
>  	Number of attempts before give up attempting to generate
>  	valid temporary addresses.
>  
> -	Default: 5
> +	Default: 3
>  
>  max_addresses - INTEGER
>  	Maximum number of autoconfigured addresses per interface.  Setting
> 
> base-commit: fa5196392691051963726787944db872420dfa75
> -- 
> 2.43.0
> 

Checked with the source and sysctl output, all works good to me.

Reviewed-by: Hangbin Liu <liuhangbin@kylinos.cn>

      reply	other threads:[~2026-11-09  0:56 UTC|newest]

Thread overview: 2+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2026-11-08  6:17 Gopal Malaviya
2026-11-09  0:56 ` Hangbin Liu [this message]

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=avEZlo0YVa5v3hu-@fedora \
    --to=hangbin.liu@linux.dev \
    --cc=corbet@lwn.net \
    --cc=davem@davemloft.net \
    --cc=edumazet@kernel.org \
    --cc=gopalmalaviya53@gmail.com \
    --cc=horms@kernel.org \
    --cc=kuba@kernel.org \
    --cc=linux-doc@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=netdev@vger.kernel.org \
    --cc=pabeni@redhat.com \
    --cc=rdunlap@infradead.org \
    --cc=skhan@linuxfoundation.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®