From: Bjorn Andersson <andersson@kernel.org>
To: david@ixit.cz
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>,
Maxime Coquelin <mcoquelin.stm32@gmail.com>,
Alexandre Torgue <alexandre.torgue@foss.st.com>,
Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>,
Henrik Rydberg <rydberg@bitmath.org>,
Konrad Dybcio <konradybcio@kernel.org>,
Petr Hodina <petr.hodina@protonmail.com>,
linux-input@vger.kernel.org,
linux-stm32@st-md-mailman.stormreply.com,
linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org,
Krzysztof Kozlowski <krzk@kernel.org>,
devicetree@vger.kernel.org, linux-arm-msm@vger.kernel.org,
phone-devel@vger.kernel.org,
Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>,
Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>,
Abel Vesa <abel.vesa@oss.qualcomm.com>
Subject: Re: [PATCH v8 5/5] arm64: dts: qcom: sdm845-google: Add STM FTS touchscreen support
Date: Mon, 9 Nov 2026 22:12:07 -0600 [thread overview]
Message-ID: <avKYaYOdaeSn2YoN@zenbook> (raw)
In-Reply-To: <20260925-stmfts5-v8-5-0fcf49e2c85f@ixit.cz>
On Fri, Sep 25, 2026 at 11:22:23PM +0200, David Heidelberg via B4 Relay wrote:
> From: Petr Hodina <petr.hodina@protonmail.com>
>
> Basic touchscreen connected to second i2c bus.
>
> Signed-off-by: Petr Hodina <petr.hodina@protonmail.com>
> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
> Reviewed-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
> Co-developed-by: David Heidelberg <david@ixit.cz>
> Signed-off-by: David Heidelberg <david@ixit.cz>
> ---
> arch/arm64/boot/dts/qcom/sdm845-google-blueline.dts | 19 ++++++++++++++++++-
> arch/arm64/boot/dts/qcom/sdm845-google-common.dtsi | 2 +-
> 2 files changed, 19 insertions(+), 2 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/sdm845-google-blueline.dts b/arch/arm64/boot/dts/qcom/sdm845-google-blueline.dts
> index fa89be500fb85..51c835dca43f1 100644
> --- a/arch/arm64/boot/dts/qcom/sdm845-google-blueline.dts
> +++ b/arch/arm64/boot/dts/qcom/sdm845-google-blueline.dts
> @@ -21,17 +21,34 @@ &framebuffer0 {
> stride = <(1080 * 4)>;
> };
>
> &i2c2 {
> clock-frequency = <1000000>;
>
> status = "okay";
>
> - /* ST,FTS @ 49 */
> + touchscreen@49 {
> + compatible = "st,stmfts5";
> + reg = <0x49>;
> +
> + pinctrl-0 = <&touchscreen_irq_n>, <&touchscreen_reset>;
> + pinctrl-names = "default";
> +
> + interrupts-extended = <&tlmm 125 IRQ_TYPE_LEVEL_LOW>;
> +
> + mode-switch-gpios = <&tlmm 136 GPIO_ACTIVE_HIGH>;
It's not clear to me how this worked or when it started failing, but due
to a conflict with the reboot-mode binding dt-validate crashes when we
reach this property.
I opened a PR to handle it here:
https://github.com/devicetree-org/dt-schema/pull/212
Regards,
Bjorn
> + reset-gpios = <&tlmm 99 GPIO_ACTIVE_LOW>;
> +
> + avdd-supply = <&vreg_l19a_3p3>;
> + vdd-supply = <&vreg_l14a_1p8>;
> +
> + touchscreen-size-x = <1080>;
> + touchscreen-size-y = <2160>;
> + };
> };
>
> &mdss_dsi0 {
> vdda-supply = <&vdda_mipi_dsi0_1p2>;
>
> status = "okay";
>
> panel@0 {
> diff --git a/arch/arm64/boot/dts/qcom/sdm845-google-common.dtsi b/arch/arm64/boot/dts/qcom/sdm845-google-common.dtsi
> index f1379857e2742..6ae1973aa8ac7 100644
> --- a/arch/arm64/boot/dts/qcom/sdm845-google-common.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sdm845-google-common.dtsi
> @@ -504,17 +504,17 @@ firmware-pins {
>
> touchscreen_reset: ts-reset-state {
> pins = "gpio99";
> function = "gpio";
> drive-strength = <8>;
> bias-pull-up;
> };
>
> - touchscreen_pins: ts-pins-gpio-state {
> + touchscreen_irq_n: ts-irq-n-gpio-state {
> pins = "gpio125";
> function = "gpio";
> drive-strength = <2>;
> bias-disable;
> };
>
> touchscreen_i2c_pins: qup-i2c2-gpio-state {
> pins = "gpio27", "gpio28";
>
> --
> 2.55.0
>
>
next prev parent reply other threads:[~2026-11-10 4:12 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-09-25 21:22 [PATCH v8 0/5] Input: support for STM FTS5 David Heidelberg via B4 Relay
2026-09-25 21:22 ` [PATCH v8 1/5] Input: stmfts - wait for controller ready after reset David Heidelberg via B4 Relay
2026-09-25 22:18 ` Dmitry Torokhov
2026-09-25 21:22 ` [PATCH v8 2/5] dt-bindings: input: touchscreen: st,stmfts: Improve example David Heidelberg via B4 Relay
2026-09-29 8:28 ` Krzysztof Kozlowski
2026-09-25 21:22 ` [PATCH v8 3/5] dt-bindings: input: touchscreen: st,stmfts: Introduce STM FTS5 David Heidelberg via B4 Relay
2026-09-29 8:40 ` Krzysztof Kozlowski
2026-09-25 21:22 ` [PATCH v8 4/5] Input: stmfts - support FTS5 David Heidelberg via B4 Relay
2026-09-25 21:22 ` [PATCH v8 5/5] arm64: dts: qcom: sdm845-google: Add STM FTS touchscreen support David Heidelberg via B4 Relay
2026-11-10 4:12 ` Bjorn Andersson [this message]
2026-11-02 3:18 ` [PATCH v8 0/5] Input: support for STM FTS5 Dmitry Torokhov
2026-11-02 9:40 ` David Heidelberg
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=avKYaYOdaeSn2YoN@zenbook \
--to=andersson@kernel.org \
--cc=abel.vesa@oss.qualcomm.com \
--cc=alexandre.torgue@foss.st.com \
--cc=conor+dt@kernel.org \
--cc=david@ixit.cz \
--cc=devicetree@vger.kernel.org \
--cc=dmitry.baryshkov@oss.qualcomm.com \
--cc=dmitry.torokhov@gmail.com \
--cc=konrad.dybcio@oss.qualcomm.com \
--cc=konradybcio@kernel.org \
--cc=krzk+dt@kernel.org \
--cc=krzk@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-input@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-stm32@st-md-mailman.stormreply.com \
--cc=mcoquelin.stm32@gmail.com \
--cc=petr.hodina@protonmail.com \
--cc=phone-devel@vger.kernel.org \
--cc=robh@kernel.org \
--cc=rydberg@bitmath.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®