From: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
To: Edward Chow <equu@openmail.cc>, Rob Herring <robh+dt@kernel.org>,
Miquel Raynal <miquel.raynal@bootlin.com>,
Richard Weinberger <richard@nod.at>,
Vignesh Raghavendra <vigneshr@ti.com>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
Cc: linux-mtd@lists.infradead.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org
Subject: Re: [PATCH] dt-bindings: mtd-partitions: Export special values
Date: Wed, 25 Oct 2023 10:20:10 +0200 [thread overview]
Message-ID: <b0e2a2c5-67e5-487e-9023-2fac5ce3ba47@linaro.org> (raw)
In-Reply-To: <20231025052937.830813-1-equu@openmail.cc>
On 25/10/2023 07:29, Edward Chow wrote:
> There are special "offset" and "size" values defined and documented in
> linux/mtd/partitions.h:
>
> // consume as much as possible, leaving size after the end of partition.
>
> // the partition will start at the next erase block.
>
> // the partition will start where the previous one ended.
>
> (Though not explicitly, they are compared against variables in uint64_t
> in drivers/mtd/mtdpart.c, so they had better be considered as such.)
>
> // the partition will extend to the end of the master MTD device.
>
> These special values could be used to define partitions automatically
> fitting to the size of the master MTD device at runtime.
>
> However, these values used not to be exported to dt-bindings, thus
> seldom used before, since they might have been only used in numeric form,
> such as "(-1) (-3)" for MTDPART_OFS_RETAIN.
>
> Now, they are exported in dt-bindings/mtd/partitions.h as 32-bit cell
> values, so 2-cell addressed should be defined to use special offset values,
> such as "MTDPART_OFS_SPECIAL MTDPART_OFS_RETAIN" for MTDPART_OFS_RETAIN in
> linux/mtd/partitions.h. An example is added to fixed-partitions.yaml.
>
> Signed-off-by: Edward Chow <equu@openmail.cc>
> ---
> .../mtd/partitions/fixed-partitions.yaml | 29 +++++++++++++++++++
> MAINTAINERS | 2 ++
> include/dt-bindings/mtd/partitions.h | 15 ++++++++++
> 3 files changed, 46 insertions(+)
> create mode 100644 include/dt-bindings/mtd/partitions.h
>
> diff --git a/Documentation/devicetree/bindings/mtd/partitions/fixed-partitions.yaml b/Documentation/devicetree/bindings/mtd/partitions/fixed-partitions.yaml
> index 331e564f29dc..a939fb52ef76 100644
> --- a/Documentation/devicetree/bindings/mtd/partitions/fixed-partitions.yaml
> +++ b/Documentation/devicetree/bindings/mtd/partitions/fixed-partitions.yaml
> @@ -164,3 +164,32 @@ examples:
> read-only;
> };
> };
> +
> + - |
> + partitions {
> + compatible = "fixed-partitions";
> + #address-cells = <2>;
> + #size-cells = <1>;
> +
> + partition@0 {
> + label = "bootloader";
> + reg = <0 0x000000 0x020000>;
> + read-only;
> + };
> +
> + firmware@1 {
> + label = "firmware";
> + /* From the end of the last partition, occupying as mush
Use Linux coding style comments.
> + * as possible, retaining 0x010000 after it,
> + * "MTDPART_OFS_SPECIAL MTDPART_OFS_NXTBLK" similar to
> + * this, but always beginning at erase block boundary. */
> + reg = <MTDPART_OFS_SPECIAL MTDPART_OFS_RETAIN 0x010000>;
> + };
> +
> + calibration@2 {
> + compatible = "fixed-partitions";
> + label = "calibration";
> + /* Appending to the last partition, occupying 0x010000 */
> + reg = <MTDPART_OFS_SPECIAL MTDPART_OFS_APPEND 0x010000>;
And where is any user of this? Example in the bindings is not user. I
would expect that you will change at least one other DTS.
> + };
> + };
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 668d1e24452d..7d6beadc8b36 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -13771,9 +13771,11 @@ T: git git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux.git mtd/fixes
> T: git git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux.git mtd/next
> F: Documentation/devicetree/bindings/mtd/
> F: drivers/mtd/
> +F: include/dt-bindings/mtd/
> F: include/linux/mtd/
> F: include/uapi/mtd/
>
> +
Drop.
> MEMSENSING MICROSYSTEMS MSA311 DRIVER
> M: Dmitry Rokosov <ddrokosov@sberdevices.ru>
> L: linux-iio@vger.kernel.org
> diff --git a/include/dt-bindings/mtd/partitions.h b/include/dt-bindings/mtd/partitions.h
> new file mode 100644
> index 000000000000..456a54a1259a
> --- /dev/null
> +++ b/include/dt-bindings/mtd/partitions.h
> @@ -0,0 +1,15 @@
> +/* SPDX-License-Identifier: GPL-2.0-only */
Dual license, as asked by checkpatch.
Best regards,
Krzysztof
next prev parent reply other threads:[~2023-10-25 8:20 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-10-25 5:29 Edward Chow
2023-10-25 7:41 ` Miquel Raynal
2023-10-25 8:20 ` Krzysztof Kozlowski [this message]
2023-10-25 12:33 ` Rob Herring
2023-10-27 9:46 ` [PATCH v2 0/2] dt-bindings: mtd: partitions: " Edward Chow
2023-10-27 9:46 ` [PATCH v2 1/2] " Edward Chow
2023-10-27 9:46 ` [PATCH v2 2/2] dt-bindings: mtd: partitions: Document " Edward Chow
2023-10-27 11:06 ` Krzysztof Kozlowski
2023-10-27 12:16 ` Rob Herring
2023-10-27 11:06 ` [PATCH v2 0/2] dt-bindings: mtd: partitions: Export " Krzysztof Kozlowski
2023-10-27 11:07 ` Krzysztof Kozlowski
2023-10-27 12:11 ` Miquel Raynal
-- strict thread matches above, loose matches on Subject: below --
2023-10-25 4:50 [PATCH] dt-bindings: mtd-partitions: " Edward Chow
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=b0e2a2c5-67e5-487e-9023-2fac5ce3ba47@linaro.org \
--to=krzysztof.kozlowski@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=equu@openmail.cc \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mtd@lists.infradead.org \
--cc=miquel.raynal@bootlin.com \
--cc=richard@nod.at \
--cc=robh+dt@kernel.org \
--cc=vigneshr@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®