mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
From: Samuel Holland <samuel@sholland.org>
To: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>,
	Vinod Koul <vkoul@kernel.org>, Chen-Yu Tsai <wens@csie.org>,
	Jernej Skrabec <jernej.skrabec@gmail.com>,
	Maxime Ripard <mripard@kernel.org>,
	Jagan Teki <jagan@amarulasolutions.com>,
	Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
	Maxime Ripard <maxime@cerno.tech>,
	Rob Herring <robh+dt@kernel.org>,
	devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
	linux-kernel@vger.kernel.org, linux-phy@lists.infradead.org,
	linux-sunxi@lists.linux.dev
Subject: Re: [PATCH 6/8] phy: allwinner: phy-sun6i-mipi-dphy: Set enable bit last
Date: Fri, 12 Aug 2022 17:31:54 -0500	[thread overview]
Message-ID: <b3a2dc61-7384-17f7-2f4f-4b6bb86bcced@sholland.org> (raw)
In-Reply-To: <YvZBmZ+SfrJuAzAs@aptenodytes>

Hi Paul,

On 8/12/22 7:03 AM, Paul Kocialkowski wrote:
> On Fri 12 Aug 22, 02:56, Samuel Holland wrote:
>> The A100 variant of the DPHY requires configuring the analog registers
>> before setting the global enable bit. Since this order also works on the
>> other variants, always use it, to minimize the differences between them.
> 
> Did you get a chance to actually test this with either DSI/CSI-2 hardware?

I have tested DSI output with the Clockwork DevTerm (D1 SoC) and Pine64
PinePhone (A64 SoC). I do not have any MIPI CSI hardware to test with.

> I vaguely remember that the order mattered. Do you have an idea of what the
> Allwinner BSP does too?

The Allwinner BSP makes the same change as this commit in its "lowlevel_v2x"
copy of the code, which is used for R40 and T7 (original DPHY) and A100 and D1
(updated DPHY). It does not make the change in "lowlevel_sun50iw1" (A64 SoC,
original DPHY), but I tested A64 with this change, and it works fine.

> Otherwise I could give it a try, at least with my MIPI CSI-2 setup
> that uses the driver.

This commit only changes sun6i_dphy_tx_power_on(). The code for RX is unchanged
-- in fact, it already sets SUN6I_DPHY_GCTL_REG last.

Regards,
Samuel

>> Signed-off-by: Samuel Holland <samuel@sholland.org>
>> ---
>>
>>  drivers/phy/allwinner/phy-sun6i-mipi-dphy.c | 8 ++++----
>>  1 file changed, 4 insertions(+), 4 deletions(-)
>>
>> diff --git a/drivers/phy/allwinner/phy-sun6i-mipi-dphy.c b/drivers/phy/allwinner/phy-sun6i-mipi-dphy.c
>> index 625c6e1e9990..9698d68d0db7 100644
>> --- a/drivers/phy/allwinner/phy-sun6i-mipi-dphy.c
>> +++ b/drivers/phy/allwinner/phy-sun6i-mipi-dphy.c
>> @@ -183,10 +183,6 @@ static int sun6i_dphy_tx_power_on(struct sun6i_dphy *dphy)
>>  		     SUN6I_DPHY_TX_TIME4_HS_TX_ANA0(3) |
>>  		     SUN6I_DPHY_TX_TIME4_HS_TX_ANA1(3));
>>  
>> -	regmap_write(dphy->regs, SUN6I_DPHY_GCTL_REG,
>> -		     SUN6I_DPHY_GCTL_LANE_NUM(dphy->config.lanes) |
>> -		     SUN6I_DPHY_GCTL_EN);
>> -
>>  	regmap_write(dphy->regs, SUN6I_DPHY_ANA0_REG,
>>  		     SUN6I_DPHY_ANA0_REG_PWS |
>>  		     SUN6I_DPHY_ANA0_REG_DMPC |
>> @@ -244,6 +240,10 @@ static int sun6i_dphy_tx_power_on(struct sun6i_dphy *dphy)
>>  			   SUN6I_DPHY_ANA2_EN_P2S_CPU_MASK,
>>  			   SUN6I_DPHY_ANA2_EN_P2S_CPU(lanes_mask));
>>  
>> +	regmap_write(dphy->regs, SUN6I_DPHY_GCTL_REG,
>> +		     SUN6I_DPHY_GCTL_LANE_NUM(dphy->config.lanes) |
>> +		     SUN6I_DPHY_GCTL_EN);
>> +
>>  	return 0;
>>  }
>>  
>> -- 
>> 2.35.1
>>
> 


  reply	other threads:[~2022-08-12 22:32 UTC|newest]

Thread overview: 25+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2022-08-12  7:55 [PATCH 0/8] phy: allwinner: phy-sun6i-mipi-dphy: Add the A100 DPHY Samuel Holland
2022-08-12  7:55 ` [PATCH 1/8] dt-bindings: sun6i-a31-mipi-dphy: Add the interrupts property Samuel Holland
2022-08-12 10:45   ` Krzysztof Kozlowski
2022-08-12 22:19     ` Samuel Holland
2022-08-16 10:18       ` Krzysztof Kozlowski
2022-09-26  9:28       ` Paul Kocialkowski
2022-09-27  9:36         ` Paul Kocialkowski
2022-08-12 12:22   ` Paul Kocialkowski
2022-08-12 22:44     ` Samuel Holland
2022-11-08  5:17       ` Samuel Holland
2022-08-12 15:13   ` Rob Herring
2022-08-12  7:55 ` [PATCH 2/8] ARM: dts: sun8i: a33: Add DPHY interrupt Samuel Holland
2022-08-12  7:55 ` [PATCH 3/8] arm64: dts: allwinner: a64: " Samuel Holland
2022-08-12  7:55 ` [PATCH 4/8] dt-bindings: sun6i-a31-mipi-dphy: Add the A100 DPHY variant Samuel Holland
2022-08-12 10:47   ` Krzysztof Kozlowski
2022-08-25 10:41   ` Paul Kocialkowski
2022-08-25 14:37     ` Samuel Holland
2022-08-12  7:56 ` [PATCH 5/8] phy: allwinner: phy-sun6i-mipi-dphy: Make RX support optional Samuel Holland
2022-09-26  9:30   ` Paul Kocialkowski
2022-08-12  7:56 ` [PATCH 6/8] phy: allwinner: phy-sun6i-mipi-dphy: Set enable bit last Samuel Holland
2022-08-12 12:03   ` Paul Kocialkowski
2022-08-12 22:31     ` Samuel Holland [this message]
2022-08-25 10:26       ` Paul Kocialkowski
2022-08-12  7:56 ` [PATCH 7/8] phy: allwinner: phy-sun6i-mipi-dphy: Add a variant power-on hook Samuel Holland
2022-08-12  7:56 ` [PATCH 8/8] phy: allwinner: phy-sun6i-mipi-dphy: Add the A100 DPHY variant Samuel Holland

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=b3a2dc61-7384-17f7-2f4f-4b6bb86bcced@sholland.org \
    --to=samuel@sholland.org \
    --cc=devicetree@vger.kernel.org \
    --cc=jagan@amarulasolutions.com \
    --cc=jernej.skrabec@gmail.com \
    --cc=kishon@ti.com \
    --cc=krzysztof.kozlowski+dt@linaro.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-phy@lists.infradead.org \
    --cc=linux-sunxi@lists.linux.dev \
    --cc=maxime@cerno.tech \
    --cc=mripard@kernel.org \
    --cc=paul.kocialkowski@bootlin.com \
    --cc=robh+dt@kernel.org \
    --cc=vkoul@kernel.org \
    --cc=wens@csie.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®