Re: [PATCH 4/4] mmc: sdhci-esdhc-imx: Remove the ENGcm07207 workaround

[Adrian Hunter <adrian.hunter@intel.com>]

On 03/05/17 13:05, Benoît Thébaudeau wrote:
> The SDHCI_QUIRK_NO_MULTIBLOCK quirk was used as a workaround for the
> ENGcm07207 erratum. However, it caused excruciatingly slow SD transfers
> (300 kB/s on average), and this erratum actually does not imply that
> multiple-block transfers are not supported, so this was overkill.
> 
> The suggested workaround for this erratum is to set SYSCTL.RSTA, but the
> simple DAT line software reset (which resets the DMA circuit among
> others) triggered by sdhci_finish_data() in case of errors seems to be
> sufficient. Indeed, generating errors in a controlled manner on i.MX25
> using the FEVT register right in the middle of read data transfers
> without this quirk shows that nothing is written to the buffer by the
> eSDHC past CMD12, and no extra Auto CMD12 is sent with AC12EN set, so
> the data transfers on AHB are properly aborted. For write data
> transfers, neither extra data nor extra Auto CMD12 is sent, as expected.
> Moreover, after intensive stress tests on i.MX25, removing
> SDHCI_QUIRK_NO_MULTIBLOCK seems to be safe.
> 
> Signed-off-by: Benoît Thébaudeau <benoit@wsystem.com>

Aside from one comment below...

I would expect to see Acks from other sdhci-esdhc-imx users.  Nevertheless,
for sdhci:

Acked-by: Adrian Hunter <adrian.hunter@intel.com>


> ---
>  drivers/mmc/host/sdhci-esdhc-imx.c | 16 +++-------------
>  1 file changed, 3 insertions(+), 13 deletions(-)
> 
> diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c
> index fa60d13..868a51f 100644
> --- a/drivers/mmc/host/sdhci-esdhc-imx.c
> +++ b/drivers/mmc/host/sdhci-esdhc-imx.c
> @@ -115,11 +115,6 @@
>   */
>  #define ESDHC_FLAG_MULTIBLK_NO_INT	BIT(1)
>  /*
> - * The flag enables the workaround for ESDHC errata ENGcm07207 which
> - * affects i.MX25 and i.MX35.
> - */
> -#define ESDHC_FLAG_ENGCM07207		BIT(2)
> -/*
>   * The flag tells that the ESDHC controller is an USDHC block that is
>   * integrated on the i.MX6 series.
>   */
> @@ -149,11 +144,11 @@ struct esdhc_soc_data {
>  };
>  
>  static struct esdhc_soc_data esdhc_imx25_data = {
> -	.flags = ESDHC_FLAG_ENGCM07207,
> +	.flags = ESDHC_FLAG_ERR004536,
>  };
>  
>  static struct esdhc_soc_data esdhc_imx35_data = {
> -	.flags = ESDHC_FLAG_ENGCM07207,
> +	.flags = ESDHC_FLAG_ERR004536,
>  };
>  
>  static struct esdhc_soc_data esdhc_imx51_data = {
> @@ -286,7 +281,7 @@ static u32 esdhc_readl_le(struct sdhci_host *host, int reg)
>  		 * ADMA2 capability of esdhc, but this bit is messed up on
>  		 * some SOCs (e.g. on MX25, MX35 this bit is set, but they
>  		 * don't actually support ADMA2). So set the BROKEN_ADMA
> -		 * uirk on MX25/35 platforms.
> +		 * quirk on MX25/35 platforms.

Please do spelling fixes as a separate patch.  Note there are several
spelling errors in comments in drivers/mmc/host/sdhci-esdhc-imx.c so you
could easily do a few of them to make a separate patch more worthwhile.

>  		 */
>  
>  		if (val & SDHCI_CAN_DO_ADMA1) {
> @@ -1278,11 +1273,6 @@ static int sdhci_esdhc_imx_probe(struct platform_device *pdev)
>  	if (IS_ERR(imx_data->pins_default))
>  		dev_warn(mmc_dev(host->mmc), "could not get default state\n");
>  
> -	if (imx_data->socdata->flags & ESDHC_FLAG_ENGCM07207)
> -		/* Fix errata ENGcm07207 present on i.MX25 and i.MX35 */
> -		host->quirks |= SDHCI_QUIRK_NO_MULTIBLOCK
> -			| SDHCI_QUIRK_BROKEN_ADMA;
> -
>  	if (esdhc_is_usdhc(imx_data)) {
>  		host->quirks2 |= SDHCI_QUIRK2_PRESET_VALUE_BROKEN;
>  		host->mmc->caps |= MMC_CAP_1_8V_DDR;
>