Stopping tasks: =========================================|
drivers/input/serio/i8042.c: 60 -> i8042 (command) [547420]
drivers/input/serio/i8042.c: 47 -> i8042 (parameter) [547420]
eth1: Orinoco-PCI entering sleep mode (state=3)
 hwsleep-0306 [08] acpi_enter_sleep_state: Entering sleep state [S3]
Back to C!
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LNKU] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [LNKH] -> GSI 9 (level, low) -> IRQ 9
 pci_irq-0370 [11] acpi_pci_irq_derive   : Unable to derive IRQ for device 0000:00:0f.0
ACPI: PCI Interrupt 0000:00:0f.0[A]: no GSI - using IRQ 0
eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
eth1: Orinoco-PCI waking up
ACPI: PCI Interrupt 0000:00:14.0[A] -> Link [LNKD] -> GSI 9 (level, low) -> IRQ 9
drivers/input/serio/i8042.c: 60 -> i8042 (command) [555896]
drivers/input/serio/i8042.c: 47 -> i8042 (parameter) [555896]
drivers/input/serio/i8042.c: 60 -> i8042 (command) [555897]
drivers/input/serio/i8042.c: 47 -> i8042 (parameter) [555897]
drivers/input/serio/i8042.c: 60 -> i8042 (command) [555898]
drivers/input/serio/i8042.c: 47 -> i8042 (parameter) [555898]
drivers/input/serio/i8042.c: f2 -> i8042 (kbd-data) [555899]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, KBD, 1) [555902]
drivers/input/serio/i8042.c: ab <- i8042 (interrupt, KBD, 1) [555909]
drivers/input/serio/i8042.c: 54 <- i8042 (interrupt, KBD, 1) [555914]
drivers/input/serio/i8042.c: ed -> i8042 (kbd-data) [555919]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, KBD, 1) [555922]
drivers/input/serio/i8042.c: 00 -> i8042 (kbd-data) [555939]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, KBD, 1) [555942]
drivers/input/serio/i8042.c: f3 -> i8042 (kbd-data) [555959]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, KBD, 1) [555962]
drivers/input/serio/i8042.c: 00 -> i8042 (kbd-data) [555979]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, KBD, 1) [555982]
drivers/input/serio/i8042.c: f4 -> i8042 (kbd-data) [555999]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, KBD, 1) [556002]
drivers/input/serio/i8042.c: ed -> i8042 (kbd-data) [556019]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, KBD, 1) [556022]
drivers/input/serio/i8042.c: 00 -> i8042 (kbd-data) [556039]
drivers/input/serio/i8042.c: fa <- i8042 (interrupt, KBD, 1) [556042]
Restarting tasks...<7>drivers/input/serio/i8042.c: 60 -> i8042 (command) [556101]
drivers/input/serio/i8042.c: 47 -> i8042 (parameter) [556101]
drivers/input/serio/i8042.c: d4 -> i8042 (command) [556102]
drivers/input/serio/i8042.c: f2 -> i8042 (parameter) [556102]
 done
drivers/input/serio/i8042.c: fe <- i8042 (interrupt, AUX, 12, timeout) [556124]
drivers/input/serio/i8042.c: d4 -> i8042 (command) [556124]
drivers/input/serio/i8042.c: ed -> i8042 (parameter) [556124]
drivers/input/serio/i8042.c: fe <- i8042 (interrupt, AUX, 12, timeout) [556146]
drivers/input/serio/i8042.c: 60 -> i8042 (command) [556146]
drivers/input/serio/i8042.c: 45 -> i8042 (parameter) [556146]
usb 1-3: USB disconnect, address 3
usb 1-3: new low speed USB device using ohci_hcd and address 4
input: USB HID v1.00 Mouse [Fujitsu Takamisawa USB Touch Panel] on usb-0000:00:02.0-3
drivers/input/serio/i8042.c: 60 -> i8042 (command) [557731]
drivers/input/serio/i8042.c: 47 -> i8042 (parameter) [557731]
drivers/input/serio/i8042.c: d4 -> i8042 (command) [557732]
drivers/input/serio/i8042.c: f2 -> i8042 (parameter) [557732]
drivers/input/serio/i8042.c: fe <- i8042 (interrupt, AUX, 12, timeout) [557753]
drivers/input/serio/i8042.c: 60 -> i8042 (command) [557753]
drivers/input/serio/i8042.c: 45 -> i8042 (parameter) [557753]
drivers/input/serio/i8042.c: 1c <- i8042 (interrupt, KBD, 1) [564765]