From: Dawid Glazik <dawid.glazik@linux.intel.com>
To: Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>, Joel Stanley <joel@jms.id.au>,
Andrew Jeffery <andrew@codeconstruct.com.au>
Cc: devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux-aspeed@lists.ozlabs.org, linux-kernel@vger.kernel.org,
maciej.lawniczak@intel.com,
Dawid Glazik <dawid.glazik@linux.intel.com>,
Andrew Lunn <andrew@lunn.ch>
Subject: [PATCH v6 3/3] ARM: dts: aspeed: Add Intel JNCRP BMC
Date: Thu, 19 Nov 2026 20:19:40 +0100 [thread overview]
Message-ID: <b951060fa8114532a96dad7a9373e739d239b071.1795114204.git.dawid.glazik@linux.intel.com> (raw)
In-Reply-To: <cover.1795114204.git.dawid.glazik@linux.intel.com>
JNCRP is an Intel x86 server platform with Intel Xeon host processors.
Its BMC is an AST2600-based platform management controller on the
platform's DC-SCM, providing out-of-band management of the host
through KCS, network and MCTP over I3C.
The BMC controls platform power and reset, and monitors CPU and memory
thermal and fault signals as well as host processor module (HPM)
presence, FRU and fault signals. It also captures POST codes.
Signed-off-by: Dawid Glazik <dawid.glazik@linux.intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
---
v6:
- Added &uart3, &uart4 and &uart_routing, with the default UART3/4
pinctrl removed to keep pins L4/L5 and B6/B7 as GPIOs
- Reworded the platform description in the commit message
- Rebased onto the current aspeed/arm/dt
v5:
- Removed bootargs from the chosen node, earlycon is for debugging only
- Added a description of the platform to the commit message
- Rebased onto the current aspeed/arm/dt
- Capitalised the first word of the subject
v4:
- Rebased onto aspeed/arm/dt of bmc/linux.git, no other changes
v3:
- Sorted nodes alphabetically
- Sorted properties per dts-coding-style
- Removed lpc-snoop label
- Removed &i3c_global since it's enabled by default
- Added &kcs3 and replaced flash layout with 128MB one
- Restored Reviewed-by from Andrew Lunn, dropped by mistake in v2
v2:
- Reviewed-by: Andrew Lunn for nodes: &mdio1, &mac1
- Replace bootargs console=ttyS4,115200n8 with stdout-path = &uart5
---
arch/arm/boot/dts/aspeed/Makefile | 1 +
.../dts/aspeed/aspeed-bmc-intel-jncrp.dts | 293 ++++++++++++++++++
2 files changed, 294 insertions(+)
create mode 100644 arch/arm/boot/dts/aspeed/aspeed-bmc-intel-jncrp.dts
diff --git a/arch/arm/boot/dts/aspeed/Makefile b/arch/arm/boot/dts/aspeed/Makefile
index 9c6b604f2b65..6f1fdb8f6f15 100644
--- a/arch/arm/boot/dts/aspeed/Makefile
+++ b/arch/arm/boot/dts/aspeed/Makefile
@@ -60,6 +60,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
aspeed-bmc-ibm-sbp1.dtb \
aspeed-bmc-ibm-system1.dtb \
aspeed-bmc-intel-avcrp.dtb \
+ aspeed-bmc-intel-jncrp.dtb \
aspeed-bmc-intel-s2600wf.dtb \
aspeed-bmc-inspur-fp5280g2.dtb \
aspeed-bmc-inspur-nf5280m6.dtb \
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-intel-jncrp.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-intel-jncrp.dts
new file mode 100644
index 000000000000..e277494fa528
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-intel-jncrp.dts
@@ -0,0 +1,293 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// Copyright 2025 Intel Corporation
+
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+
+/ {
+ compatible = "intel,jncrp-bmc", "aspeed,ast2600";
+ model = "Intel JNCRP BMC";
+
+ aliases {
+ serial4 = &uart5;
+ };
+
+ chosen {
+ stdout-path = &uart5;
+ };
+
+ memory@80000000 {
+ device_type = "memory";
+ reg = <0x80000000 0x40000000>;
+ };
+};
+
+&fmc {
+ status = "okay";
+
+ flash@0 {
+ label = "bmc";
+ spi-max-frequency = <50000000>;
+ spi-rx-bus-width = <4>;
+ m25p,fast-read;
+
+ status = "okay";
+
+#include "openbmc-flash-layout-128.dtsi"
+ };
+};
+
+&gpio0 {
+ gpio-line-names =
+ /*A0-A7*/ "", "", "", "", "", "", "", "",
+ /*B0-B7*/ "PWRGD_AUX_PWRGD_BMC_CPU", "", "", "", "", "", "",
+ "FP_ID_LED_N",
+ /*C0-C7*/ "FM_FORCE_BMC_UPDATE_N", "RST_RGMII_PHYRST_N",
+ "FM_TPM_EN_PULSE", "", "", "",
+ "DBP_HOOK3_CPU_FBRK_OUT_R_N", "DBP_PRSNT_IN_N",
+ /*D0-D7*/ "CPU_ERR0_N", "CPU_ERR1_N", "CPU_ERR2_N", "DBP_ASD_BMC_PRDY_N",
+ "FM_SPD_SWITCH_CTRL_N", "", "", "",
+ /*E0-E7*/ "", "", "", "ID_BUTTON", "", "", "", "",
+ /*F0-F7*/ "", "", "FM_AGGREGATOR_MODE_N", "", "", "",
+ "FP_LED_STATUS_GREEN_R_N", "FP_LED_STATUS_AMBER_R_N",
+ /*G0-G7*/ "", "", "", "", "", "", "", "",
+ /*H0-H7*/ "", "", "", "", "", "", "", "",
+ /*I0-I7*/ "", "", "", "", "", "", "", "",
+ /*J0-J7*/ "", "", "", "", "", "", "", "",
+ /*K0-K7*/ "", "", "", "", "", "", "", "",
+ /*L0-L7*/ "", "", "", "", "PREQ_N", "FM_P3V3_SW_ENA", "", "",
+ /*M0-M7*/ "", "", "", "", "", "", "", "",
+ /*N0-N7*/ "", "", "", "", "", "", "", "",
+ /*O0-O7*/ "", "", "", "", "", "", "NMI_BUTTON", "",
+ /*P0-P7*/ "RESET_BUTTON", "RESET_OUT", "POWER_BUTTON", "POWER_OUT",
+ "", "", "", "LED_BMC_HB_LED_N",
+ /*Q0-Q7*/ "", "", "", "", "", "", "", "",
+ /*R0-R7*/ "", "", "", "", "", "", "", "",
+ /*S0-S7*/ "CPU_CATERR_IERR_N", "CPU_CATERR_MCERR_N", "FM_BMC_FRU_WP_N",
+ "FM_INTRUSION_CABLE_PRES_N", "PWRGD_CPU_AUXPWRGD",
+ "FM_P3V_BAT_SCALED_EN", "REMOTE_DEBUG_ENABLE", "",
+ /*T0-T7*/ "", "", "", "", "", "", "", "",
+ /*U0-U7*/ "", "", "", "", "", "", "", "",
+ /*V0-V7*/ "SIO_S3", "SIO_S5", "", "SIO_ONCONTROL",
+ "SIO_POWER_GOOD", "", "", "",
+ /*W0-W7*/ "", "", "", "", "", "", "", "",
+ /*X0-X7*/ "", "", "POST_COMPLETE", "", "", "", "", "",
+ /*Y0-Y7*/ "FM_BMC_CMOS_CLR_R_N", "PLTRST_N", "FM_BMC_SAFS_EN",
+ "IRQ_PSU_ALERT_LVC3_N", "", "", "", "",
+ /*Z0-Z7*/ "", "", "", "", "", "", "", "";
+
+ status = "okay";
+
+ spd-switch-cpu-hog {
+ gpio-hog;
+ gpios = <ASPEED_GPIO(D, 4) GPIO_ACTIVE_HIGH>;
+ output-low;
+ };
+};
+
+&i2c4 {
+ status = "okay";
+};
+
+&i2c5 {
+ multi-master;
+
+ status = "okay";
+};
+
+&i2c6 {
+ status = "okay";
+};
+
+&i2c7 {
+ multi-master;
+
+ status = "okay";
+};
+
+&i2c8 {
+ multi-master;
+
+ status = "okay";
+};
+
+&i2c9 {
+ multi-master;
+
+ status = "okay";
+};
+
+&i2c10 {
+ multi-master;
+
+ status = "okay";
+};
+
+&i2c11 {
+ status = "okay";
+};
+
+&i2c12 {
+ multi-master;
+
+ status = "okay";
+};
+
+&i2c13 {
+ multi-master;
+
+ status = "okay";
+};
+
+&i2c14 {
+ status = "okay";
+};
+
+&i2c15 {
+ multi-master;
+
+ status = "okay";
+};
+
+&i3c1 {
+ i2c-scl-hz = <1000000>;
+ mctp-controller;
+
+ status = "okay";
+};
+
+&kcs3 {
+ aspeed,lpc-io-reg = <0xca2>;
+
+ status = "okay";
+};
+
+&lpc {
+ lpc-snoop@80 {
+ snoop-ports = <0x80>;
+
+ status = "okay";
+ };
+};
+
+&mac1 {
+ clocks = <&syscon ASPEED_CLK_GATE_MAC2CLK>,
+ <&syscon ASPEED_CLK_MAC2RCLK>;
+ clock-names = "MACCLK", "RCLK";
+ phy-handle = <ðphy1>;
+ phy-mode = "rgmii-id";
+ pinctrl-0 = <&pinctrl_rgmii2_default>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&mdio1 {
+ status = "okay";
+
+ ethphy1: ethernet-phy@0 {
+ compatible = "ethernet-phy-id001c.c916";
+ reg = <0>;
+ reset-assert-us = <10000>;
+ reset-deassert-us = <50000>;
+ reset-gpios = <&gpio0 ASPEED_GPIO(C, 1) GPIO_ACTIVE_LOW>;
+ };
+};
+
+&rtc {
+ status = "okay";
+};
+
+&sgpiom0 {
+ bus-frequency = <2000000>;
+ gpio-line-names =
+ /*A, 0-7*/ "CPU0_VRHOT_N", "LED_POSTCODE_0_LSB",
+ "CPU0_THERMTRIP_N", "LED_POSTCODE_1",
+ "CPU0_MEMTRIP_N", "LED_POSTCODE_2",
+ "CPU0_MEM_VRHOT_N", "LED_POSTCODE_3",
+ "CPU0_MEM_HOT_N", "LED_POSTCODE_4",
+ "CPU0_MON_FAIL_N", "LED_POSTCODE_5",
+ "CPU1_VRHOT_N", "LED_POSTCODE_6",
+ "CPU1_THERMTRIP_N", "LED_POSTCODE_7_MSB",
+ /*B, 8-15*/ "CPU1_MEMTRIP_N", "FM_ASYNC_WARM_RESET_REQ",
+ "CPU1_MEM_VRHOT_N", "HPM_FRU_READ_DONE",
+ "CPU1_MEM_HOT_N", "FM_ASYNC_GLOBAL_RESET_REQ",
+ "CPU1_MON_FAIL_N", "BMC_BOOT_DONE",
+ "CPU2_VRHOT_N", "NMI_OUT",
+ "CPU2_THERMTRIP_N", "AGGREGATOR_MODE",
+ "CPU2_MEMTRIP_N", "RST_I3C_PCIE_HUB_N",
+ "CPU2_MEM_VRHOT_N", "",
+ /*C, 16-23*/ "CPU2_MEM_HOT_N", "HPM0_PRESENT",
+ "CPU2_MON_FAIL_N", "HPM1_PRESENT",
+ "CPU3_VRHOT_N", "HPM2_PRESENT",
+ "CPU3_THERMTRIP_N", "HPM3_PRESENT",
+ "CPU3_MEMTRIP_N", "HPM0_SOURCE_TO_DESTINATION_FAIL",
+ "CPU3_MEM_VRHOT_N", "HPM1_SOURCE_TO_DESTINATION_FAIL",
+ "CPU3_MEM_HOT_N", "HPM2_SOURCE_TO_DESTINATION_FAIL",
+ "CPU3_MON_FAIL_N", "HPM3_SOURCE_TO_DESTINATION_FAIL",
+ /*D, 24-31*/ "FM_BMC_VAL_EN", "HPM0_FRU_VALID",
+ "FM_SERIAL_BOOT", "HPM1_FRU_VALID",
+ "FM_INTRUSION_CABLE_PRES_N", "HPM2_FRU_VALID",
+ "USB_OC_P2_3_N", "HPM3_FRU_VALID",
+ "FM_SYSTEM_COOLING_MODE0", "FM_S2D_DISCOVERY_DONE",
+ "FM_SYSTEM_COOLING_MODE1", "", "", "", "", "",
+ /*E, 32-39*/ "DBP_PMODE_S0_PWROK", "", "DBP_PMODE_PLTRST", "",
+ "DBP_PMODE_GLOBALRESET", "", "DBP_PMODE_CPU_PWRGD", "",
+ "FM_SMBUS_RDY", "", "FM_LEAK_DETECTION", "",
+ "FM_LEAK_CBL_PRSNT_N", "", "FM_LEAK_CBL_FAULT_N", "",
+ /*F, 40-47*/ "CPU0_SKTOCC1_N", "CPU0_SKT_FAULT_LED",
+ "CPU0_SKTOCC2_N", "CPU1_SKT_FAULT_LED",
+ "CPU0_MISMATCH", "CPU2_SKT_FAULT_LED",
+ "CPU1_SKTOCC1_N", "CPU3_SKT_FAULT_LED",
+ "CPU1_SKTOCC2_N", "", "CPU1_MISMATCH", "",
+ "CPU2_SKTOCC1_N", "", "CPU2_SKTOCC2_N", "",
+ /*G, 48-55*/ "CPU2_MISMATCH", "", "CPU3_SKTOCC1_N", "",
+ "CPU3_SKTOCC2_N", "", "CPU3_MISMATCH", "",
+ "HPM0_PRSNT_N", "", "HPM1_PRSNT_N", "",
+ "HPM2_PRSNT_N", "", "HPM3_PRSNT_N", "",
+ /*H, 56-63*/ "", "", "", "", "", "", "", "", "", "", "", "", "", "", "", "",
+ /*I, 64-71*/ "", "", "", "", "", "", "", "", "", "", "", "", "", "", "", "",
+ /*J, 72-79*/ "", "", "", "", "", "", "", "", "", "", "", "", "", "", "", "",
+ /*K, 80-87*/ "FM_BOARD_REV_ID0", "", "FM_BOARD_REV_ID1", "",
+ "FM_BOARD_REV_ID2", "", "FM_BOARD_SKU_ID0", "",
+ "FM_BOARD_SKU_ID1", "", "FM_BOARD_SKU_ID2", "",
+ "FM_BOARD_SKU_ID3", "", "FM_BOARD_SKU_ID4", "",
+ /*L, 88-95*/ "FM_BOARD_SKU_ID5", "", "FM_BOARD_SKU_ID6", "",
+ "FM_BOARD_SKU_ID7", "", "", "", "", "", "", "",
+ "", "", "", "",
+ /*M, 96-103*/ "", "", "", "", "", "", "", "", "", "", "", "", "", "", "", "",
+ /*N, 104-111*/ "", "", "", "", "", "", "", "", "", "", "", "", "", "", "", "",
+ /*O, 112-119*/ "", "", "", "", "", "", "", "", "", "", "", "", "", "", "", "",
+ /*P, 120-127*/ "", "", "", "", "", "", "", "", "", "", "", "", "", "", "", "";
+ ngpios = <128>;
+
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&uart3 {
+ /delete-property/ pinctrl-names;
+ /delete-property/ pinctrl-0;
+
+ status = "okay";
+};
+
+&uart4 {
+ /delete-property/ pinctrl-names;
+ /delete-property/ pinctrl-0;
+
+ status = "okay";
+};
+
+&uart5 {
+ status = "okay";
+};
+
+&uart_routing {
+ status = "okay";
+};
--
2.43.0
prev parent reply other threads:[~2026-11-19 18:27 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-11-19 19:19 [PATCH v6 0/3] ARM: dts: aspeed: Add Intel AVCRP and JNCRP BMC platforms Dawid Glazik
2026-11-19 19:19 ` [PATCH v6 1/3] dt-bindings: arm: aspeed: Add Intel AVCRP and JNCRP boards Dawid Glazik
2026-11-19 19:19 ` [PATCH v6 2/3] ARM: dts: aspeed: Add Intel AVCRP BMC Dawid Glazik
2026-11-19 19:19 ` Dawid Glazik [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=b951060fa8114532a96dad7a9373e739d239b071.1795114204.git.dawid.glazik@linux.intel.com \
--to=dawid.glazik@linux.intel.com \
--cc=andrew@codeconstruct.com.au \
--cc=andrew@lunn.ch \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=joel@jms.id.au \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-aspeed@lists.ozlabs.org \
--cc=linux-kernel@vger.kernel.org \
--cc=maciej.lawniczak@intel.com \
--cc=robh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®