Re: [PATCH] phy: phy-twl4030-usb: Fix cable state handling

[Kishon Vijay Abraham I <kishon@ti.com>]

On 25/03/19 4:56 AM, Tony Lindgren wrote:
> With the recent regulator changes I noticed new warnings on doing rmmod of
> phy-twl4030-usb:
> 
> WARNING: CPU: 0 PID: 1080 at drivers/regulator/core.c:2046 _regulator_put
> ...
> 
> Turns out we can currently miss disconnect at least for cases where status
> is 0 and linkstat is 0. And in that case doing rmmod phy-twl4030-usb will
> produce the regulator_put() warning.
> 
> This is because the missed disconnect causes unbalanced PM runtime calls
> and the regulators will be on exit.
> 
> Let's fix the issue by using an atomic flag for the cable state to make
> sure that PM runtime won't get out of sync with the cable state. That
> way we can also simplify the code a bit.
> 
> Note that we can also drop the old comments, those relate to issues that
> the battery charger driver and musb driver is dealing with rather than
> the USB PHY driver.
> 
> Cc: NeilBrown <neilb@suse.com>
> Signed-off-by: Tony Lindgren <tony@atomide.com>

merged, thanks!

-Kishon
> ---
>  drivers/phy/ti/phy-twl4030-usb.c | 35 ++++++++++++--------------------
>  1 file changed, 13 insertions(+), 22 deletions(-)
> 
> diff --git a/drivers/phy/ti/phy-twl4030-usb.c b/drivers/phy/ti/phy-twl4030-usb.c
> --- a/drivers/phy/ti/phy-twl4030-usb.c
> +++ b/drivers/phy/ti/phy-twl4030-usb.c
> @@ -172,6 +172,7 @@ struct twl4030_usb {
>  
>  	int			irq;
>  	enum musb_vbus_id_status linkstat;
> +	atomic_t		connected;
>  	bool			vbus_supplied;
>  	bool			musb_mailbox_pending;
>  
> @@ -575,39 +576,29 @@ static irqreturn_t twl4030_usb_irq(int irq, void *_twl)
>  {
>  	struct twl4030_usb *twl = _twl;
>  	enum musb_vbus_id_status status;
> -	bool status_changed = false;
>  	int err;
>  
>  	status = twl4030_usb_linkstat(twl);
>  
>  	mutex_lock(&twl->lock);
> -	if (status >= 0 && status != twl->linkstat) {
> -		status_changed =
> -			cable_present(twl->linkstat) !=
> -			cable_present(status);
> -		twl->linkstat = status;
> -	}
> +	twl->linkstat = status;
>  	mutex_unlock(&twl->lock);
>  
> -	if (status_changed) {
> -		/* FIXME add a set_power() method so that B-devices can
> -		 * configure the charger appropriately.  It's not always
> -		 * correct to consume VBUS power, and how much current to
> -		 * consume is a function of the USB configuration chosen
> -		 * by the host.
> -		 *
> -		 * REVISIT usb_gadget_vbus_connect(...) as needed, ditto
> -		 * its disconnect() sibling, when changing to/from the
> -		 * USB_LINK_VBUS state.  musb_hdrc won't care until it
> -		 * starts to handle softconnect right.
> -		 */
> -		if (cable_present(status)) {
> +	if (cable_present(status)) {
> +		if (atomic_add_unless(&twl->connected, 1, 1)) {
> +			dev_dbg(twl->dev, "%s: cable connected %i\n",
> +				__func__, status);
>  			pm_runtime_get_sync(twl->dev);
> -		} else {
> +			twl->musb_mailbox_pending = true;
> +		}
> +	} else {
> +		if (atomic_add_unless(&twl->connected, -1, 0)) {
> +			dev_dbg(twl->dev, "%s: cable disconnected %i\n",
> +				__func__, status);
>  			pm_runtime_mark_last_busy(twl->dev);
>  			pm_runtime_put_autosuspend(twl->dev);
> +			twl->musb_mailbox_pending = true;
>  		}
> -		twl->musb_mailbox_pending = true;
>  	}
>  	if (twl->musb_mailbox_pending) {
>  		err = musb_mailbox(status);
>