mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
From: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
To: Josua Mayer <josua@solid-run.com>,
	devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
	linux-arm-kernel@lists.infradead.org
Cc: Shawn Guo <shawnguo@kernel.org>,
	Sascha Hauer <s.hauer@pengutronix.de>,
	Pengutronix Kernel Team <kernel@pengutronix.de>,
	Fabio Estevam <festevam@gmail.com>,
	NXP Linux Team <linux-imx@nxp.com>,
	Rob Herring <robh+dt@kernel.org>,
	Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
	Conor Dooley <conor+dt@kernel.org>, Li Yang <leoyang.li@nxp.com>
Subject: Re: [PATCH 3/3] arm64: dts: freescale: Add support for LX2162 SoM & Clearfog Board
Date: Fri, 16 Jun 2023 13:39:38 +0200	[thread overview]
Message-ID: <c25630ca-c791-287f-36a4-ebc0559d6541@linaro.org> (raw)
In-Reply-To: <20230616110610.32173-4-josua@solid-run.com>

On 16/06/2023 13:06, Josua Mayer wrote:
> Add support for the SolidRun LX2162A System on Module (SoM), and the
> Clearfog evaluation board.
> 
> The SoM has few software-controllable features:
> - AR8035 Ethernet PHY
> - eMMC
> - SPI Flash
> - fan controller
> - various eeproms
> 

Thank you for your patch. There is something to discuss/improve.

> +
> +&i2c2 {
> +	/* retimer: ds250df410@18 */
> +
> +	i2c-switch@70 {
> +		compatible = "nxp,pca9546";
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		reg = <0x70>;

reg is usually just after compatible.

...

> +
> +&emdio1 {
> +	/*
> +	 * SoM has a phy at address 1 connected to SoC Ethernet Controller 1.
> +	 * It competes for WRIOP MAC17, and no connector has been wired.
> +	 */
> +	/delete-node/ ethernet-phy@1;
> +
> +	ethernet_phy0: mv88e2580@8 {

Node names should be generic. See also explanation and list of examples
in DT specification:
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation

> +		reg = <8>;
> +		compatible = "ethernet-phy-ieee802.3-c45";
> +		max-speed = <1000>;
> +	};
> +
> +	ethernet_phy1: mv88e2580@9 {
> +		reg = <9>;
> +		compatible = "ethernet-phy-ieee802.3-c45";
> +		max-speed = <1000>;
> +	};
> +
> +	ethernet_phy2: mv88e2580@a {
> +		reg = <10>;
> +		compatible = "ethernet-phy-ieee802.3-c45";
> +		max-speed = <1000>;
> +	};
> +
> +	ethernet_phy3: mv88e2580@b {
> +		reg = <11>;
> +		compatible = "ethernet-phy-ieee802.3-c45";
> +		max-speed = <1000>;
> +	};
> +
> +	ethernet_phy4: mv88e2580@c {
> +		reg = <12>;
> +		compatible = "ethernet-phy-ieee802.3-c45";
> +		max-speed = <1000>;
> +	};
> +
> +	ethernet_phy5: mv88e2580@d {
> +		reg = <13>;
> +		compatible = "ethernet-phy-ieee802.3-c45";
> +		max-speed = <1000>;
> +	};
> +
> +	ethernet_phy6: mv88e2580@e {
> +		reg = <14>;
> +		compatible = "ethernet-phy-ieee802.3-c45";
> +		max-speed = <1000>;
> +	};
> +
> +	ethernet_phy7: mv88e2580@f {
> +		reg = <15>;
> +		compatible = "ethernet-phy-ieee802.3-c45";
> +		max-speed = <1000>;
> +	};
> +};
> +
> +&esdhc0 {
> +	status = "okay";
> +	sd-uhs-sdr104;
> +	sd-uhs-sdr50;
> +	sd-uhs-sdr25;
> +	sd-uhs-sdr12;
> +};
> +
> +&pcie3 {
> +	status = "disabled";
> +};
> +
> +&pcie4 {
> +	status = "disabled";
> +};
> +
> +&pcs_mdio3 {
> +	status = "okay";
> +};
> +
> +&pcs_mdio4 {
> +	status = "okay";
> +};
> +
> +&pcs_mdio5 {
> +	status = "okay";
> +};
> +
> +&pcs_mdio6 {
> +	status = "okay";
> +};
> +
> +&pcs_mdio11 {
> +	status = "okay";
> +};
> +
> +&pcs_mdio12 {
> +	status = "okay";
> +};
> +
> +&pcs_mdio13 {
> +	status = "okay";
> +};
> +
> +&pcs_mdio14 {
> +	status = "okay";
> +};
> +
> +&pcs_mdio15 {
> +	status = "okay";
> +};
> +
> +&pcs_mdio16 {
> +	status = "okay";
> +};
> +
> +&pcs_mdio17 {
> +	status = "okay";
> +};
> +
> +&pcs_mdio18 {
> +	status = "okay";
> +};
> +
> +&serdes_1 {
> +	status = "okay";
> +};
> +
> +&serdes_2 {
> +	status = "okay";
> +};
> +
> +&uart0 {
> +	status = "okay";
> +};
> +
> +&usb0 {
> +	status = "okay";
> +};
> diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2162a-sr-som.dtsi b/arch/arm64/boot/dts/freescale/fsl-lx2162a-sr-som.dtsi
> new file mode 100644
> index 000000000000..49e03b6600d6
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/fsl-lx2162a-sr-som.dtsi
> @@ -0,0 +1,78 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +//
> +// Device Tree file for LX2162A-SOM
> +//
> +// Copyright 2021 Rabeeh Khoury <rabeeh@solid-run.com>
> +// Copyright 2023 Josua Mayer <josua@solid-run.com>
> +
> +&crypto {
> +	status = "okay";
> +};
> +
> +&dpmac17 {
> +	phy-handle = <&ethernet_phy0>;
> +	phy-connection-type = "rgmii-id";
> +};
> +
> +&emdio1 {
> +	status = "okay";
> +
> +	ethernet_phy0: ethernet-phy@1 {
> +		reg = <1>;
> +	};
> +};
> +
> +&esdhc1 {
> +	status = "okay";
> +	bus-width = <8>;
> +	mmc-hs200-1_8v;
> +	mmc-hs400-1_8v;
> +};
> +
> +&fspi {
> +	status = "okay";
> +
> +	flash@0 {
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		compatible = "m25p80", "jedec,spi-nor";
> +		m25p,fast-read;
> +		spi-max-frequency = <50000000>;
> +		reg = <0>;

Fix the order of properties. compatible is always first, then the reg.

> +		/* The following setting enables 1-1-8 (CMD-ADDR-DATA) mode */
> +		spi-rx-bus-width = <8>;
> +		// spi-tx-bus-width = <8>;

Don't add dead code without appropriate comment why it is dead.

> +	};
> +};
> +
> +&i2c0 {
> +	status = "okay";
> +
> +	fan-controller@18 {
> +		compatible = "ti,amc6821";
> +		reg = <0x18>;
> +		cooling-min-state = <0>;
> +		cooling-max-state = <9>;
> +		#cooling-cells = <2>;
> +	};
> +
> +	ddr_spd: eeprom@51 {
> +		reg = <0x57>;
> +		compatible = "st,24c02", "atmel,24c02";

Ditto

> +		read-only;
> +	};
> +
> +	config_eeprom: eeprom@57 {
> +		reg = <0x57>;
> +		compatible = "st,24c02", "atmel,24c02";

Ditto

> +	};
> +};
> +
> +&i2c4 {
> +	status = "okay";
> +
> +	variable_eeprom: eeprom@54 {
> +		reg = <0x54>;
> +		compatible = "st,24c2048", "atmel,24c2048";

ditto

> +	};
> +};

Best regards,
Krzysztof


  reply	other threads:[~2023-06-16 11:40 UTC|newest]

Thread overview: 13+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2023-06-16 11:06 [PATCH 0/3] " Josua Mayer
2023-06-16 11:06 ` [PATCH 1/3] arm64: dts: lx2160a: describe the SerDes block #2 Josua Mayer
2023-06-16 11:06 ` [PATCH 2/3] dt-bindings: arm: Add SolidRun LX2162A SoM & Clearfog Board Josua Mayer
2023-06-16 11:36   ` Krzysztof Kozlowski
2023-06-16 13:32     ` Josua Mayer
2023-06-16 16:57       ` Andreas Kemnade
2023-06-17 13:34         ` Josua Mayer
2023-06-16 16:59       ` Krzysztof Kozlowski
2023-06-17 14:09         ` Josua Mayer
2023-06-16 11:06 ` [PATCH 3/3] arm64: dts: freescale: Add support for LX2162 " Josua Mayer
2023-06-16 11:39   ` Krzysztof Kozlowski [this message]
2023-06-16 12:57     ` Josua Mayer
2023-06-16 16:59       ` Krzysztof Kozlowski

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=c25630ca-c791-287f-36a4-ebc0559d6541@linaro.org \
    --to=krzysztof.kozlowski@linaro.org \
    --cc=conor+dt@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=festevam@gmail.com \
    --cc=josua@solid-run.com \
    --cc=kernel@pengutronix.de \
    --cc=krzysztof.kozlowski+dt@linaro.org \
    --cc=leoyang.li@nxp.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-imx@nxp.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=robh+dt@kernel.org \
    --cc=s.hauer@pengutronix.de \
    --cc=shawnguo@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®