[PATCH v3 4/8] serial: exar: add optional board_init function

[Parker Newman <parker@finest.io>]

From: Parker Newman <pnewman@connecttech.com>

- Add an optional "board_init()" function pointer to struct
exar8250_board which is called once during probe prior to setting up
the ports.

- Fix several "missing identifier name" warnings from checkpatch in
struct exar8250_platform and struct exar8250_board:

WARNING: function definition argument <arg> should also have an
identifier name

- Fix warning from checkpatch:
WARNING: please, no space before tabs
+ * 0^I^I2 ^IMode bit 0$

Changes in v3:
 - Renamed board_setup to board_init.
 - Changed pci_err to dev_err_probe
 - Added note above about checkpatch fixes

Signed-off-by: Parker Newman <pnewman@connecttech.com>
---
 drivers/tty/serial/8250/8250_exar.c | 23 +++++++++++++++++------
 1 file changed, 17 insertions(+), 6 deletions(-)

diff --git a/drivers/tty/serial/8250/8250_exar.c b/drivers/tty/serial/8250/8250_exar.c
index 388dd60ad23a..cf7900bd2974 100644
--- a/drivers/tty/serial/8250/8250_exar.c
+++ b/drivers/tty/serial/8250/8250_exar.c
@@ -133,7 +133,7 @@
  *
  * MPIO		Port	Function
  * ----		----	--------
- * 0		2 	Mode bit 0
+ * 0		2	Mode bit 0
  * 1		2	Mode bit 1
  * 2		2	Terminate bus
  * 3		-	<reserved>
@@ -169,22 +169,24 @@ struct exar8250_platform {
 	int (*rs485_config)(struct uart_port *port, struct ktermios *termios,
 			    struct serial_rs485 *rs485);
 	const struct serial_rs485 *rs485_supported;
-	int (*register_gpio)(struct pci_dev *, struct uart_8250_port *);
-	void (*unregister_gpio)(struct uart_8250_port *);
+	int (*register_gpio)(struct pci_dev *pcidev, struct uart_8250_port *port);
+	void (*unregister_gpio)(struct uart_8250_port *port);
 };

 /**
  * struct exar8250_board - board information
  * @num_ports: number of serial ports
  * @reg_shift: describes UART register mapping in PCI memory
- * @setup: quirk run at ->probe() stage
+ * @board_init: quirk run once at ->probe() stage before setting up ports
+ * @setup: quirk run at ->probe() stage for each port
  * @exit: quirk run at ->remove() stage
  */
 struct exar8250_board {
 	unsigned int num_ports;
 	unsigned int reg_shift;
-	int	(*setup)(struct exar8250 *, struct pci_dev *,
-			 struct uart_8250_port *, int);
+	int     (*board_init)(struct exar8250 *priv);
+	int	(*setup)(struct exar8250 *priv, struct pci_dev *pcidev,
+			 struct uart_8250_port *port, int idx);
 	void	(*exit)(struct pci_dev *pcidev);
 };

@@ -772,6 +774,15 @@ exar_pci_probe(struct pci_dev *pcidev, const struct pci_device_id *ent)
 	if (rc)
 		return rc;

+	if (board->board_init) {
+		rc = board->board_init(priv);
+		if (rc) {
+			dev_err_probe(&pcidev->dev, rc,
+					"failed to init serial board\n");
+			return rc;
+		}
+	}
+
 	for (i = 0; i < nr_ports && i < maxnr; i++) {
 		rc = board->setup(priv, pcidev, &uart, i);
 		if (rc) {
--
2.43.2