Re: [PATCH v5 5/7] arm64: dts: qcom: Add initial support for MSM8952

[Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>]

On 10/11/26 6:51 PM, Muzaffer Kadir via B4 Relay wrote:
> From: Muzaffer Kadir <muzafferkadir@mainlining.org>
> 
> Add initial support for MSM8952 SoC.
> 
> AI help is used for calculating qfprom nodes.
> 
> Downstream reference for port is [1] which is very lightly modified
> version of [2].

Generally this looks good, couple more comments

[...]

> +	soc: soc@0 {
> +		compatible = "simple-bus";
> +		ranges = <0 0 0 0xffffffff>;

this is equal to `ranges;`

[...]


> +		sdhc_1: mmc@7824900 {
> +			compatible = "qcom,msm8952-sdhci", "qcom,sdhci-msm-v4";
> +			reg = <0x07824900 0x500>, <0x07824000 0x800>, <0x7824e00 0x200>;
> +			reg-names = "hc", "core", "cqhci";

Please break up these into one-per-line (also for properties below)
the last reg entry needs a leading zero

(in general one-per-line is cool)

[...]


> +		usb: usb@78db000 {
> +			compatible = "qcom,ci-hdrc";
> +			reg = <0x078db000 0x200>,
> +			      <0x078db200 0x200>;
> +			interrupts-extended = <&mpm 58 IRQ_TYPE_LEVEL_HIGH>,
> +					      <&mpm 49 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&gcc GCC_USB_HS_AHB_CLK>,
> +				 <&gcc GCC_USB_HS_SYSTEM_CLK>;
> +			clock-names = "iface",
> +				      "core";
> +			assigned-clocks = <&gcc GCC_USB_HS_SYSTEM_CLK>;
> +			assigned-clock-rates = <80000000>;
> +			resets = <&gcc GCC_USB_HS_BCR>;
> +			reset-names = "core";
> +			hnp-disable;
> +			srp-disable;
> +			adp-disable;
> +			ahb-burst-config = <0>;
> +			dr_mode = "otg";

dr_mode = otg is default - you can drop it

[...]

> +			pll_opp_table_c1: opp-table {
> +				compatible = "operating-points-v2";
> +
> +				opp-499200000 {
> +					opp-hz = /bits/ 64 <499200000>;
> +				};
> +
> +				opp-806400000 {
> +					opp-hz = /bits/ 64 <806400000>;
> +				};
> +
> +				opp-960000000 {
> +					opp-hz = /bits/ 64 <960000000>;
> +				};
> +
> +				opp-1094400000 {
> +					opp-hz = /bits/ 64 <1094400000>;
> +				};
> +
> +				opp-1344000000 {
> +					opp-hz = /bits/ 64 <1344000000>;
> +				};
> +
> +				opp-1440000000 {
> +					opp-hz = /bits/ 64 <1440000000>;
> +				};
> +
> +				opp-1516800000 {
> +					opp-hz = /bits/ 64 <1516800000>;
> +				};
> +
> +				opp-1651200000 {
> +					opp-hz = /bits/ 64 <1651200000>;
> +				};

Drop the last entry for the same reasons you explained

[...]


> +		a53pll_cci: clock@b1d0000 {
> +			compatible = "qcom,msm8939-a53pll";

This needs a 8952-specific compatible (bindings-only fallback
is fine)

> +			reg = <0x0b1d0000 0x40>;
> +			clocks = <&xo_board>;
> +			clock-names = "xo";
> +			#clock-cells = <0>;
> +		};
> +
> +		apcs2: mailbox@b1d1000 {
> +			compatible = "qcom,msm8939-apcs-kpss-global", "syscon";

Likewise
> +			reg = <0x0b1d1000 0x1000>;
> +			clocks = <&a53pll_cci>,
> +				 <&gcc GPLL0_VOTE>,
> +				 <&rpmcc RPM_SMD_XO_CLK_SRC>;
> +			clock-names = "pll",
> +				      "aux",
> +				      "ref";
> +			#clock-cells = <0>;
> +			#mbox-cells = <1>;
> +		};
> +
> +		adsp: remoteproc@c200000 {
> +			compatible = "qcom,msm8996-adsp-pil";

And likewise

also IMEM, DSI, RPMPD, RPMCC

[...]

> +	thermal-zones {
> +		aoss0-thermal {
> +			polling-delay-passive = <250>;

TSENS sensors are interrupt-driven so you don't need polling

AOSS is surely the wrong name - that hw didn't come until years
later than 8952 was released. I can't find a mapping of the
sensors for this SoC right now, so either drop these or give them
some generic names

[...]

> +	timer {
> +		compatible = "arm,armv8-timer";
> +		interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
> +			     <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
> +			     <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
> +			     <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
> +		clock-frequency = <19200000>;

Drop this property, it's only needed for very broken FWs

Konrad