From: Michael McAllister <me@michaelmcallister.org>
To: Bjorn Andersson <andersson@kernel.org>,
Konrad Dybcio <konradybcio@kernel.org>
Cc: Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>,
linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org
Subject: [PATCH 0/2] arm64: dts: qcom: Add initial Motorola Moto G10 support
Date: Thu, 22 Oct 2026 22:18:23 +0100 [thread overview]
Message-ID: <cover.1792703903.git.me@michaelmcallister.org> (raw)
This series adds an initial device tree for the Motorola Moto G10
(capri), based on the Qualcomm Snapdragon 460 (SM4250). It adds the board
compatible and describes eMMC, USB-C, power and volume keys, the firmware
framebuffer, regulators, GPU, Wi-Fi, Bluetooth and remote processors.
The board uses the shared PM6125 and PMI632 definitions, with its own
reserved-memory layout and firmware PSCI state IDs. Modem, ADSP and GPU
firmware paths are namespaced under qcom/motorola/capri/.
Native panel, touchscreen, speaker and battery support need separate
driver and binding submissions and are outside this series.
Based on Qualcomm arm64-for-7.4 (Linux 7.3-rc1). Binding and full DT schema
checks pass. The W=1 DTB build reports an inherited unused DSI address/size-
cells warning in sm6115.dtsi, also reproduced with OnePlus Billie2.
Runtime checks covered booting with all eight CPUs, read-only eMMC access
and USB ECM transfers. simpledrm and the power/volume input devices
registered. Thermal readings and an active watchdog were observed.
Physical button events and visible framebuffer output remain unconfirmed.
GPU, Wi-Fi, Bluetooth, remote processors and suspend were not exercised;
the minimal RAM image contained no wireless/DSP firmware or modules.
The test ran without a panic or warning backtrace. A PSCI PC-mode firmware
warning also occurs with the phone's installed kernel; suspend and deeper
idle states remain untested.
For the stock Android bootloader, testing used out-of-tree handoff code
to select this DTB while retaining the firmware RAM map, initramfs and
factory Wi-Fi address, plus an arm64 Image alignment wrapper. That code
is not included here. No other device-specific driver patches were used.
Michael McAllister (2):
dt-bindings: arm: qcom: Add Motorola Moto G10
arm64: dts: qcom: Add Motorola Moto G10
.../devicetree/bindings/arm/qcom.yaml | 1 +
arch/arm64/boot/dts/qcom/Makefile | 1 +
.../boot/dts/qcom/sm4250-motorola-capri.dts | 452 ++++++++++++++++++
3 files changed, 454 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/sm4250-motorola-capri.dts
base-commit: d053e38e614fb2e383b298ce8fc308a780d7f209
next reply other threads:[~2026-10-22 21:20 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-10-22 21:18 Michael McAllister [this message]
2026-10-22 20:39 ` [PATCH 1/2] dt-bindings: arm: qcom: Add Motorola Moto G10 Michael McAllister
2026-10-22 20:40 ` [PATCH 2/2] arm64: dts: " Michael McAllister
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=cover.1792703903.git.me@michaelmcallister.org \
--to=me@michaelmcallister.org \
--cc=andersson@kernel.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=konradybcio@kernel.org \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®