mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
From: Phil Elwell <phil@raspberrypi.org>
To: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: devel@driverdev.osuosl.org, daniels@collabora.com,
	"Lee Jones" <lee@kernel.org>,
	linux-kernel@vger.kernel.org,
	"Michael Zoran" <mzoran@crowfest.net>,
	"Noralf Trønnes" <noralf@tronnes.org>,
	linux-rpi-kernel <linux-rpi-kernel@lists.infradead.org>,
	linux-arm-kernel@lists.infradead.org
Subject: [PATCH] staging: vc04_services: Fix bulk cache maintenance
Date: Thu, 4 May 2017 10:58:20 +0100	[thread overview]
Message-ID: <d0edaf52-45e2-6fda-bb86-1a9b5e1a5425@raspberrypi.org> (raw)

vchiq_arm supports transfers less than one page and at arbitrary
alignment, using the dma-mapping API to perform its cache maintenance
(even though the VPU drives the DMA hardware). Read (DMA_FROM_DEVICE)
operations use cache invalidation for speed, falling back to
clean+invalidate on partial cache lines, with writes (DMA_TO_DEVICE)
using flushes.

If a read transfer has ends which aren't page-aligned, performing cache
maintenance as if they were whole pages can lead to memory corruption
since the partial cache lines at the ends (and any cache lines before or
after the transfer area) will be invalidated. This bug was masked until
the disabling of the cache flush in flush_dcache_page().

Honouring the requested transfer start- and end-points prevents the
corruption.

Fixes: cf9caf192988 ("staging: vc04_services: Replace dmac_map_area with dmac_map_sg")
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
---
 .../interface/vchiq_arm/vchiq_2835_arm.c           | 31 +++++++++++++---------
 1 file changed, 19 insertions(+), 12 deletions(-)

diff --git a/drivers/staging/vc04_services/interface/vchiq_arm/vchiq_2835_arm.c b/drivers/staging/vc04_services/interface/vchiq_arm/vchiq_2835_arm.c
index 3aeffcb..02e9736 100644
--- a/drivers/staging/vc04_services/interface/vchiq_arm/vchiq_2835_arm.c
+++ b/drivers/staging/vc04_services/interface/vchiq_arm/vchiq_2835_arm.c
@@ -501,8 +501,15 @@ int vchiq_platform_init(struct platform_device *pdev, VCHIQ_STATE_T *state)
 	 */
 	sg_init_table(scatterlist, num_pages);
 	/* Now set the pages for each scatterlist */
-	for (i = 0; i < num_pages; i++)
-		sg_set_page(scatterlist + i, pages[i], PAGE_SIZE, 0);
+	for (i = 0; i < num_pages; i++)	{
+		unsigned int len = PAGE_SIZE - offset;
+
+		if (len > count)
+			len = count;
+		sg_set_page(scatterlist + i, pages[i], len, offset);
+		offset = 0;
+		count -= len;
+	}
 
 	dma_buffers = dma_map_sg(g_dev,
 				 scatterlist,
@@ -523,20 +530,20 @@ int vchiq_platform_init(struct platform_device *pdev, VCHIQ_STATE_T *state)
 		u32 addr = sg_dma_address(sg);
 
 		/* Note: addrs is the address + page_count - 1
-		 * The firmware expects the block to be page
+		 * The firmware expects blocks after the first to be page-
 		 * aligned and a multiple of the page size
 		 */
 		WARN_ON(len == 0);
-		WARN_ON(len & ~PAGE_MASK);
-		WARN_ON(addr & ~PAGE_MASK);
+		WARN_ON(i && (i != (dma_buffers - 1)) && (len & ~PAGE_MASK));
+		WARN_ON(i && (addr & ~PAGE_MASK));
 		if (k > 0 &&
-		    ((addrs[k - 1] & PAGE_MASK) |
-			((addrs[k - 1] & ~PAGE_MASK) + 1) << PAGE_SHIFT)
-		    == addr) {
-			addrs[k - 1] += (len >> PAGE_SHIFT);
-		} else {
-			addrs[k++] = addr | ((len >> PAGE_SHIFT) - 1);
-		}
+		    ((addrs[k - 1] & PAGE_MASK) +
+		     (((addrs[k - 1] & ~PAGE_MASK) + 1) << PAGE_SHIFT))
+		    == (addr & PAGE_MASK))
+			addrs[k - 1] += ((len + PAGE_SIZE - 1) >> PAGE_SHIFT);
+		else
+			addrs[k++] = (addr & PAGE_MASK) |
+				(((len + PAGE_SIZE - 1) >> PAGE_SHIFT) - 1);
 	}
 
 	/* Partial cache lines (fragments) require special measures */
-- 
1.9.1

             reply	other threads:[~2017-05-04 10:26 UTC|newest]

Thread overview: 5+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2017-05-04  9:58 Phil Elwell [this message]
2017-05-04 17:51 ` Stefan Wahren
2017-05-10  8:42   ` Phil Elwell
2017-05-10  9:06     ` Greg Kroah-Hartman
2017-05-10  9:11       ` Phil Elwell

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=d0edaf52-45e2-6fda-bb86-1a9b5e1a5425@raspberrypi.org \
    --to=phil@raspberrypi.org \
    --cc=daniels@collabora.com \
    --cc=devel@driverdev.osuosl.org \
    --cc=gregkh@linuxfoundation.org \
    --cc=lee@kernel.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-rpi-kernel@lists.infradead.org \
    --cc=mzoran@crowfest.net \
    --cc=noralf@tronnes.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®