Re: [PATCH] arm64: dts: qcom: Add device tree for TUXEDO Elite 14 Gen1

[Georg Gottleuber <g.gottleuber@tuxedocomputers.com>]

Am 06.03.25 um 13:41 schrieb Krzysztof Kozlowski:
...
> 
> Please run scripts/checkpatch.pl and fix reported warnings. After that,
> run also `scripts/checkpatch.pl --strict` and (probably) fix more
> warnings. Some warnings can be ignored, especially from --strict run,
> but the code here looks like it needs a fix. Feel free to get in touch
> if the warning is not clear.
> 
> It does not look like you tested the DTS against bindings. Please run
> `make dtbs_check W=1` (see
> Documentation/devicetree/bindings/writing-schema.rst or
> https://www.linaro.org/blog/tips-and-tricks-for-validating-devicetree-sources-with-the-devicetree-schema/
> for instructions).
> Maybe you need to update your dtschema and yamllint. Don't rely on
> distro packages for dtschema and be sure you are using the latest
> released dtschema.

Thank you for the advice and the offer to answer further questions.
Didn't know that dtb_check exists.

> ...
> 
>> +
>> +       eusb3_repeater: redriver@47 {
>> +               compatible = "nxp,ptn3222";
>> +               reg = <0x47>;
>> +               #phy-cells = <0>;
>> +
>> +               vdd1v8-supply = <&vreg_l4b_1p8>;
>> +               vdd3v3-supply = <&vreg_l13b_3p0>;
>> +
>> +               reset-gpios = <&tlmm 124 GPIO_ACTIVE_LOW>;
>> +
>> +               pinctrl-0 = <&eusb3_reset_n>;
>> +               pinctrl-names = "default";
> 
> No graph? Isn't it needed?

What do you mean by ‘no graph’?

>> +       };
>> +
>> +       eusb5_repeater: redriver@43 {
>> +               compatible = "nxp,ptn3222";
>> +               reg = <0x43>;
>> +               #phy-cells = <0>;
>> +
>> +               vdd1v8-supply = <&vreg_l4b_1p8>;
>> +               vdd3v3-supply = <&vreg_l13b_3p0>;
>> +
>> +               reset-gpios = <&tlmm 184 GPIO_ACTIVE_LOW>;
>> +
>> +               pinctrl-0 = <&eusb6_reset_n>;
>> +               pinctrl-names = "default";
>> +       };
>> +
>> +       eusb6_repeater: redriver@4f {
>> +               compatible = "nxp,ptn3222";
>> +               reg = <0x4f>;
>> +               #phy-cells = <0>;
>> +
>> +               vdd1v8-supply = <&vreg_l4b_1p8>;
>> +               vdd3v3-supply = <&vreg_l13b_3p0>;
>> +
>> +               reset-gpios = <&tlmm 111 GPIO_ACTIVE_LOW>;
>> +
>> +               pinctrl-0 = <&eusb6_reset_n>;
>> +               pinctrl-names = "default";
>> +       };
>> +
> 
> Stray blank line

Sorry. Will fix this.

>> +};
>> +
>> +&mdss {
>> +       status = "okay";
>> +};
>> +
> 
> 
>> +
>> +&usb_1_ss0_dwc3_hs {
>> +       remote-endpoint = <&pmic_glink_ss0_hs_in>;
>> +};
>> +
>> +&usb_1_ss0_qmpphy_out {
>> +       remote-endpoint = <&pmic_glink_ss0_ss_in>;
>> +};
>> +
> 
> Here as well

Same here.

Regards,
Georg