Re: [PATCH] clk: qcom: gdsc: Fix handling of hw control enable/disable

[Stanimir Varbanov <stanimir.varbanov@linaro.org>]

Hi Sricharan,

On 01/10/2017 09:29 PM, Sricharan wrote:
> Hi stan,
> 
>> -----Original Message-----
>> From: linux-arm-msm-owner@vger.kernel.org [mailto:linux-arm-msm-owner@vger.kernel.org] On Behalf Of Stanimir Varbanov
>> Sent: Tuesday, January 10, 2017 10:14 PM
>> To: Rajendra Nayak <rnayak@codeaurora.org>; sboyd@codeaurora.org; mturquette@baylibre.com
>> Cc: linux-clk@vger.kernel.org; linux-arm-msm@vger.kernel.org; linux-kernel@vger.kernel.org; sricharan@codeaurora.org
>> Subject: Re: [PATCH] clk: qcom: gdsc: Fix handling of hw control enable/disable
>>
>> Hi Rajendra,
>>
>> On 01/10/2017 07:54 AM, Rajendra Nayak wrote:
>>> Once a gdsc is brought in and out of HW control, there is a
>>> power down and up cycle which can take upto 1us. Polling on
>>> the gdsc status immediately after the hw control enable/disable
>>> can mislead software/firmware to belive the gdsc is already either on
>>> or off, while its yet to complete the power cycle.
>>> To avoid this add a 1us delay post a enable/disable of HW control
>>> mode.
>>>
>>> Also after the HW control mode is disabled, poll on the status to
>>> check gdsc status reflects its 'on' before force disabling it
>>> in software.
>>>
>>> Reported-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
>>> Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
>>> ---
>>>
>>> Stan,
>>> If there was a specific issue you saw with venus because of the missing
>>> delay and poll, can you check if this fixes any of that.
>>
>> Something more about the issue.
>>
>> I had re-designed venus driver on three platform drivers venus-core,
>> venus-dec and venus-enc in order to be able to control those three
>> power-domains (VENUS_GDSC, VENUS_CORE0_GDSC and VENUS_CORE1_GDSC).
>>
>> After that I abstracted MMAGIC hw on a separate mmagic driver. This
>> driver just controls mmagic clocks and GDSC in its runtime_suspend and
>> runtime_resume methods.
>>
>> The DT nodes looks like:
>>
>> mmagic_video {
>> 	compatible = "qcom,msm8996-mmagic";
>> 	clocks = <&rpmcc MSM8996_RPM_SMD_MMAXI_CLK>,
>> 		 <&mmcc MMSS_MMAGIC_AHB_CLK>,
>> 		 <&mmcc MMSS_MMAGIC_CFG_AHB_CLK>,
>> 		 <&mmcc MMAGIC_VIDEO_NOC_CFG_AHB_CLK>,
>> 		 <&mmcc MMSS_MMAGIC_MAXI_CLK>,
>> 		 <&mmcc MMAGIC_VIDEO_AXI_CLK>,
>> 		 <&mmcc SMMU_VIDEO_AHB_CLK>,
>> 		 <&mmcc SMMU_VIDEO_AXI_CLK>;
>> 	power-domains = <&mmcc MMAGIC_VIDEO_GDSC>;
>>
>> 	video-codec {
>> 		compatible = "qcom,msm8996-venus";
>> 		clocks = <&mmcc VIDEO_CORE_CLK>,
>> 			 <&mmcc VIDEO_AHB_CLK>,
>> 			 <&mmcc VIDEO_AXI_CLK>,
>> 			 <&mmcc VIDEO_MAXI_CLK>;
>> 		power-domains = <&mmcc VENUS_GDSC>;
>> 		...
>>
>> 		video-decoder {
>> 			compatible = "venus-decoder";
>> 			clocks = "subcore0";
>> 			clock-names = <&mmcc VIDEO_SUBCORE0_CLK>;
>> 			power-domains = <&mmcc VENUS_CORE0_GDSC>;
>> 		};
>>
>> 		video-encoder {
>> 			compatible = "venus-encoder";
>> 			clocks = "subcore1";
>> 			clock-names = <&mmcc VIDEO_SUBCORE1_CLK>;
>> 			power-domains = <&mmcc VENUS_CORE1_GDSC>;
>> 		};
>> 	};
>> };
>>
>> Note that mmagic_video is a parent dt node for smmu_video DT node so
>> that clocks and mmagic_video gdsc will be enabled once smmu driver is
>> instantiated by venus-core diriver.
>>
> 
> mmagic_video is a parent DT for smmu_video ? , so there are no clocks
> populated for the smmu node as such ?

Yes, I completely disabled runtime pm in the arm-smmu driver.

> 
>> Now when video-dec driver calls pm_runtime_get_sync() the sequence of
>> enabling is:
>>
>> MMAGIC_VIDEO_GDSC -> MMAGIC clocks and SMMU clocks -> VENUS_GDSC ->
>> VIDEO clocks -> VENUS_CORE0_GDSC -> VIDEO subcore0 clock
>>
>> When video-dec platform driver calls pm_runtime_put_sync() we should
>> disabling of GDSC and clocks in the reversed oder.
>>
>> The issue comes when I have ran video decoder, the decoder hw finish
>> stream decoding and we want to suspend venus core. The issue is that
>> when I start disabling SMMU_VIDEO_AXI_CLK and/or MMAGIC_VIDEO_AXI_CLK
>> the system reboots.
>>
>> I have added a delay (200ms) before disabling mmagic clocks and then
>> everything is fine again.
>>
>> Any idea?
>>
> 
> Can you share me a branch, i can have a quick check with a t32
> if there is any crash logged in the TZ buffer when the system reboots.

I can share a branch but you will need my initramfs too.

I don't think it is tz related, most probably it is MMAGIC sequence
issue or something in GDSC/MMCC.

-- 
regards,
Stan