From: Mark Zhang <markz@nvidia.com>
To: Billy Laws <blaws05@gmail.com>
Cc: Lee Jones <lee.jones@linaro.org>, <linux-kernel@vger.kernel.org>,
<linux-tegra@vger.kernel.org>,
Laxman Dewangan <ldewangan@nvidia.com>,
Venkat Reddy Talla <vreddytalla@nvidia.com>
Subject: Re: [2/2] mfd: max77620: Add low battery monitor support
Date: Tue, 29 Jan 2019 17:03:54 +0800 [thread overview]
Message-ID: <e1ebcd02-2d25-a6b7-081b-578878be15b4@nvidia.com> (raw)
In-Reply-To: <CAFUUQHM88kVh0ov1G30Sz9WQKJRY4p78hBMporL1xU=aY_tNCA@mail.gmail.com>
On 1/29/2019 3:36 PM, Billy Laws wrote:
> Sure, that's fine with me, will send then this gets accepted. Two
> other things: you should probably set the reg to 0 if the property
> isn't specified as regmap_add_irqchip sets it to 0xff (basically all
> enabled on highest limit), and you haven't updated the dt-bindings.
Billy, v2 is out, dt-bindings patches are added.
But after a second thought, I don't think regmap_add_irqchip might set
registers to 0xff. I mean, for 2 registers which this patch set touches,
they're not IRQ registers(mask/status/...), so regmap_add_irqchip should
not touch them so I didn't make changes to driver codes in v2.
Mark
>
> On Tue, Jan 29, 2019 at 6:52 AM Mark Zhang <markz@nvidia.com> wrote:
>>
>> On 1/27/2019 10:54 PM, Billy Laws wrote:
>>> >This patch adds PMIC configurations for low-battery
>>> >monitoring by handling max77620 register CNFGGLBL1.
>>> >
>>> It might be an idea to add lbhyst configuration here and support using
>>> custom lbdac values to specify a different cutoff point.
>>
>> Yeah this patch doesn't have support to program LBHYST & LBDAC because
>> according to our experiences, we don't have requirement to modify them
>> when low battery monitor support added.
>>
>> I think we can create a new patch to support these 2 fields in the future
>> when we really need them. Or you can create a patch if you have requirement
>> for them, is this OK to you Billy?
>>
>> Mark
>>
>>>
>>> See: https://datasheetspdf.com/pdf-file/924230/Maxim/MAX8698C/1 pg 46
>>> >Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
>>> >Signed-off-by: Venkat Reddy Talla <vreddytalla@nvidia.com>
>>> >Signed-off-by: Mark Zhang <markz@nvidia.com>
>>> >---
>>> > drivers/mfd/max77620.c | 57 +++++++++++++++++++++++++++++++++++++++++-
>>> > 1 file changed, 56 insertions(+), 1 deletion(-)
>>> >
>>> >diff --git a/drivers/mfd/max77620.c b/drivers/mfd/max77620.c
>>> >index f58143103185..9e50d145afd8 100644
>>> >--- a/drivers/mfd/max77620.c
>>> >+++ b/drivers/mfd/max77620.c
>>> >@@ -474,6 +474,57 @@ static int
>>> max77620_init_backup_battery_charging(struct max77620_chip *chip)
>>> > return ret;
>>> > }
>>> >
>>> >+static int max77620_init_low_battery_monitor(struct max77620_chip *chip)
>>> >+{
>>> >+ struct device *dev = chip->dev;
>>> >+ struct device_node *np;
>>> >+ bool pval;
>>> >+ u8 mask = 0;
>>> >+ u8 val = 0;
>>> >+ int ret;
>>> >+
>>> >+ np = of_get_child_by_name(dev->of_node, "low-battery-monitor");
>>> >+ if (!np) {
>>> >+ dev_info(dev, "Low battery monitoring support disabled\n");
>>> >+ return 0;
>>> >+ }
>>> >+
>>> >+ pval = of_property_read_bool(np, "maxim,low-battery-dac-enable");
>>> >+ if (pval) {
>>> >+ mask |= MAX77620_CNFGGLBL1_LBDAC_EN;
>>> >+ val |= MAX77620_CNFGGLBL1_LBDAC_EN;
>>> >+ }
>>> >+
>>> >+ pval = of_property_read_bool(np, "maxim,low-battery-dac-disable");
>>> >+ if (pval)
>>> >+ mask |= MAX77620_CNFGGLBL1_LBDAC_EN;
>>> >+
>>> >+ pval = of_property_read_bool(np, "maxim,low-battery-shutdown-enable");
>>> >+ if (pval) {
>>> >+ mask |= MAX77620_CNFGGLBL1_MPPLD;
>>> >+ val |= MAX77620_CNFGGLBL1_MPPLD;
>>> >+ }
>>> >+
>>> >+ pval = of_property_read_bool(np, "maxim,low-battery-shutdown-disable");
>>> >+ if (pval)
>>> >+ mask |= MAX77620_CNFGGLBL1_MPPLD;
>>> >+
>>> >+ pval = of_property_read_bool(np, "maxim,low-battery-reset-enable");
>>> >+ if (pval) {
>>> >+ mask |= MAX77620_CNFGGLBL1_LBRSTEN;
>>> >+ val |= MAX77620_CNFGGLBL1_LBRSTEN;
>>> >+ }
>>> >+
>>> >+ pval = of_property_read_bool(np, "maxim,low-battery-reset-disable");
>>> >+ if (pval)
>>> >+ mask |= MAX77620_CNFGGLBL1_LBRSTEN;
>>> >+
>>> >+ ret = regmap_update_bits(chip->rmap, MAX77620_REG_CNFGGLBL1, mask, val);
>>> >+ if (ret < 0)
>>> >+ dev_err(dev, "Reg CNFGGLBL1 update failed: %d\n", ret);
>>> >+ return ret;
>>> >+}
>>> >+
>>> > static int max77620_read_es_version(struct max77620_chip *chip)
>>> > {
>>> > unsigned int val;
>>> >@@ -563,7 +614,11 @@ static int max77620_probe(struct i2c_client *client,
>>> > if (ret < 0)
>>> > return ret;
>>> >
>>> >- ret = devm_mfd_add_devices(chip->dev, PLATFORM_DEVID_NONE,
>>> >+ ret = max77620_init_low_battery_monitor(chip);
>>> >+ if (ret < 0)
>>> >+ return ret;
>>> >+
>>> >+ ret = devm_mfd_add_devices(chip->dev, PLATFORM_DEVID_NONE,
>>> > mfd_cells, n_mfd_cells, NULL, 0,
>>> > regmap_irq_get_domain(chip->top_irq_data));
>>> > if (ret < 0) {
>>>
next prev parent reply other threads:[~2019-01-29 9:04 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-01-27 14:54 Billy Laws
2019-01-28 7:15 ` Lee Jones
2019-01-28 7:16 ` Lee Jones
2019-01-28 7:33 ` Billy Laws
2019-01-29 6:52 ` Mark Zhang
2019-01-29 7:36 ` Billy Laws
2019-01-29 7:41 ` 答复: " Mark Zhang
2019-01-29 9:03 ` Mark Zhang [this message]
2019-01-29 13:33 ` Billy Laws
2019-01-30 1:44 ` 答复: " Mark Zhang
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=e1ebcd02-2d25-a6b7-081b-578878be15b4@nvidia.com \
--to=markz@nvidia.com \
--cc=blaws05@gmail.com \
--cc=ldewangan@nvidia.com \
--cc=lee.jones@linaro.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-tegra@vger.kernel.org \
--cc=vreddytalla@nvidia.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®