uration information
Allocating PCI resources starting at 2c000000 (gap: 2c000000:d2c00000)
Built 1 zonelists
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Initializing CPU#0
Kernel command line: vga=0x317 root=/dev/hda1 ro 
CPU 0 irqstacks, hard=c047b000 soft=c0479000
PID hash table entries: 2048 (order: 11, 32768 bytes)
Detected 3200.606 MHz processor.
Using pmtmr for high-res timesource
Console: colour dummy device 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 449848k/458176k available (2341k kernel code, 7836k reserved, 984k data, 204k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 6356.99 BogoMIPS (lpj=3178496)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 0000459d 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 0000459d 00000000 00000000
monitor/mwait feature present.
using mwait in idle threads.
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 0000459d 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
CPU0: Intel Mobile Intel(R) Pentium(R) 4 CPU 3.20GHz stepping 04
Booting processor 1/1 eip 3000
CPU 1 irqstacks, hard=c047c000 soft=c047a000
Initializing CPU#1
Calibrating delay loop... 6389.76 BogoMIPS (lpj=3194880)
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 0000459d 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 0000459d 00000000 00000000
monitor/mwait feature present.
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 0000459d 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel P4/Xeon Extended MCE MSRs (12) available
CPU1: Thermal monitoring enabled
CPU1: Intel Mobile Intel(R) Pentium(R) 4 CPU 3.20GHz stepping 04
Total of 2 processors activated (12746.75 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=-1
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
CPU0 attaching sched-domain:
 domain 0: span 3
  groups: 1 2
  domain 1: span 3
   groups: 3
CPU1 attaching sched-domain:
 domain 0: span 3
  groups: 2 1
  domain 1: span 3
   groups: 3
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfd958, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050309
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] segment is 0
PCI: Ignoring BAR0-3 of IDE controller 0000:00:14.1
Boot video device is 0000:01:05.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Can't get handler for 0000:00:00.0
ACPI: Can't get handler for 0000:02:00.0
ACPI: Can't get handler for 0000:02:02.0
ACPI: Can't get handler for 0000:02:04.1
ACPI: Can't get handler for 0000:02:04.2
ACPI: Can't get handler for 0000:02:04.3
ACPI: PCI Interrupt Link [LNK0] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNK1] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNK2] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNK3] (IRQs 10 11) *0, disabled.
ACPI: Embedded Controller [EC0] (gpe 6)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: No ACPI bus support for 00:00
ACPI: No ACPI bus support for 00:01
ACPI: No ACPI bus support for 00:02
ACPI: No ACPI bus support for 00:03
ACPI: No ACPI bus support for 00:04
ACPI: No ACPI bus support for 00:05
ACPI: No ACPI bus support for 00:06
ACPI: No ACPI bus support for 00:07
ACPI: No ACPI bus support for 00:08
pnp: PnP ACPI: found 9 devices
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
pnp: 00:06: ioport range 0x1080-0x1080 has been reserved
pnp: 00:06: ioport range 0x220-0x22f has been reserved
pnp: 00:06: ioport range 0x40b-0x40b has been reserved
pnp: 00:06: ioport range 0x4d0-0x4d1 has been reserved
Machine check exception polling timer started.
inotify device minor=63
Initializing Cryptographic API
vesafb: framebuffer at 0xf0000000, mapped to 0xdc880000, using 3072k, total 65536k
vesafb: mode is 1024x768x16, linelength=2048, pages=41
vesafb: protected mode interface info at c000:52f4
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
ACPI: No ACPI bus support for vesafb.0
ACPI: AC Adapter [ACAD] (on-line)
ACPI: Battery Slot [BAT1] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
ACPI: Video Device [VGA] (multi-head: yes  rom: no  post: no)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected Ati IGP9100/M chipset
agpgart: AGP aperture is 64M @ 0xec000000
PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
ACPI: No ACPI bus support for i8042
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ACPI: No ACPI bus support for serial8250
ACPI: No ACPI bus support for serio0
ACPI: No ACPI bus support for serio1
ACPI: No ACPI bus support for serio2
ACPI: No ACPI bus support for serio3
ACPI: No ACPI bus support for serio4
ACPI: PCI Interrupt 0000:00:14.6[B] -> GSI 17 (level, low) -> IRQ 17
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
8139cp: pci dev 0000:02:03.0 (id 10ec:8139 rev 10) is not an 8139C+ compatible chip
8139cp: Try the "8139too" driver instead.
8139too Fast Ethernet driver 0.9.27
ACPI: PCI Interrupt 0000:02:03.0[A] -> GSI 19 (level, low) -> IRQ 19
eth0: RealTek RTL8139 at 0xdc84a800, 00:02:3f:d8:41:8d, IRQ 19
eth0:  Identified 8139 chip type 'RTL-8100B/8139D'
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ATIIXP: IDE controller at PCI slot 0000:00:14.1
ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 16
ATIIXP: chipset revision 0
ATIIXP: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0x8070-0x8077, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0x8078-0x807f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: TOSHIBA MK8025GAS, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ACPI: No ACPI bus support for 0.0
Probing IDE interface ide1...
hdc: MATSHITADVD-RAM UJ-820S, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
ACPI: No ACPI bus support for 1.0
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
hda: max request size: 128KiB
hda: 156301488 sectors (80026 MB), CHS=65535/16/63, UDMA(100)
hda: cache flushes supported
 hda: hda1 hda2 hda3
hdc: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ohci1394: $Rev: 1250 $ Ben Collins <bcollins@debian.org>
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
ACPI: No ACPI bus support for fw-host0
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[16]  MMIO=[e8210000-e82107ff]  Max Packet=[2048]
ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 16 (level, low) -> IRQ 16
Yenta: CardBus bridge found at 0000:02:04.0 [1179:ff01]
Yenta: ISA IRQ mask 0x0010, PCI irq 16
Socket status: 30000010
pcmcia: I/O behind socket: 0xa000 - 0xafff
cs: IO port probe 0xa000-0xafff: clean.
pcmcia: Memory behind socket: 0xe8200000 - 0xe82fffff
ACPI: PCI Interrupt 0000:00:13.2[A] -> GSI 19 (level, low) -> IRQ 19
ehci_hcd 0000:00:13.2: ATI Technologies Inc EHCI USB Controller
ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:13.2: irq 19, io mem 0xe8003000
ehci_hcd 0000:00:13.2: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
ACPI: No ACPI bus support for usb1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
ACPI: No ACPI bus support for 1-0:1.0
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 19
ohci_hcd 0000:00:13.0: ATI Technologies Inc OHCI USB Controller #1
ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:13.0: irq 19, io mem 0xe8001000
ACPI: No ACPI bus support for usb2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ACPI: No ACPI bus support for 2-0:1.0
ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 19
ohci_hcd 0000:00:13.1: ATI Technologies Inc OHCI USB Controller #2
ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:13.1: irq 19, io mem 0xe8002000
ACPI: No ACPI bus support for usb3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 3 ports detected
ACPI: No ACPI bus support for 3-0:1.0
cs: memory probe 0xe8200000-0xe82fffff: excluding 0xe8200000-0xe825ffff
ACPI: No ACPI bus support for 0.0
usb 2-1: new low speed USB device using ohci_hcd and address 2
ACPI: No ACPI bus support for 00023f485b40072f
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00023f485b40072f]
ACPI: No ACPI bus support for 2-1
ACPI: No ACPI bus support for 2-1:1.0
usb 2-3: new low speed USB device using ohci_hcd and address 3
ACPI: No ACPI bus support for 2-3
ACPI: No ACPI bus support for 2-3:1.0
input: USB HID v1.10 Mouse [Microsoft Microsoft 5-Button Mouse with IntelliEye(TM)] on usb-0000:00:13.0-1
input: USB HID v1.10 Keyboard [Key Tronic Keytronic USB Keyboard] on usb-0000:00:13.0-3
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
mice: PS/2 mouse device common for all mice
Advanced Linux Sound Architecture Driver Version 1.0.9rc2  (Thu Mar 24 10:33:39 2005 UTC).
ALSA device list:
  No soundcards found.
NET: Registered protocol family 2
IP: routing cache hash table of 2048 buckets, 32Kbytes
TCP established hash table entries: 16384 (order: 6, 262144 bytes)
TCP bind hash table entries: 16384 (order: 5, 196608 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
NET: Registered protocol family 1
NET: Registered protocol family 17
p4-clockmod: P4/Xeon(TM) CPU On-Demand Clock Modulation available
Starting balanced_irq
ACPI wakeup devices: 
ELAN OHC1 OHC2 EHCI MODM 
ACPI: (supports S0 S3 S4 S5)
ReiserFS: hda1: found reiserfs format "3.6" with standard journal
input: AT Translated Set 2 keyboard on isa0060/serio0
ReiserFS: hda1: using ordered data mode
ReiserFS: hda1: journal params: device hda1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda1: checking transaction log (hda1)
ReiserFS: hda1: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 204k freed
[drm] Initialized drm 1.0.0 20040925
ACPI: PCI Interrupt 0000:01:05.0[A] -> GSI 16 (level, low) -> IRQ 16
[drm] Initialized radeon 1.15.0 20050125 on minor 0: ATI Technologies Inc RS300M AGP [Radeon Mobility 9100IGP]
ReiserFS: hda2: found reiserfs format "3.6" with standard journal
ReiserFS: hda2: using ordered data mode
ReiserFS: hda2: journal params: device hda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda2: checking transaction log (hda2)
ReiserFS: hda2: Using r5 hash to sort names
ath_hal: module license 'Proprietary' taints kernel.
ath_hal: 0.9.14.9 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413)
wlan: 0.8.4.5 (EXPERIMENTAL)
ath_rate_onoe: 1.0
ath_pci: 0.9.4.12 (EXPERIMENTAL)
ACPI: PCI Interrupt 0000:02:02.0[A] -> GSI 18 (level, low) -> IRQ 18
ath0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
ath0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
ath0: mac 5.9 phy 4.3 radio 4.6
ath0: 802.11 address: 00:11:f5:03:6c:f0
ath0: Use hw queue 0 for WME_AC_BE traffic
ath0: Use hw queue 1 for WME_AC_BK traffic
ath0: Use hw queue 2 for WME_AC_VI traffic
ath0: Use hw queue 3 for WME_AC_VO traffic
ath0: Atheros 5212: mem=0xe8200000, irq=18
ACPI: PCI Interrupt 0000:00:14.5[B] -> GSI 17 (level, low) -> IRQ 17
atiixp: codec reset timeout
ACPI: PCI Interrupt 0000:00:14.6[B] -> GSI 17 (level, low) -> IRQ 17
alps.c: Enabling hardware tapping
input: PS/2 Mouse on isa0060/serio4
input: AlpsPS/2 ALPS GlidePoint on isa0060/serio4
cs: IO port probe 0x100-0x4ff: clean.
cs: IO port probe 0x800-0x8ff: clean.
cs: IO port probe 0xc00-0xcff: excluding 0xc00-0xc07 0xc10-0xc17 0xc50-0xc57 0xc68-0xc6f 0xcd0-0xcd7
cs: IO port probe 0xa00-0xaff: clean.
ttyS0 at I/O 0x3f8 (irq = 16) is a 16550A
eth0: link up, 100Mbps, half-duplex, lpa 0x40A1
mtrr: 0xf0000000,0x8000000 overlaps existing 0xf0000000,0x4000000
mtrr: 0xf0000000,0x8000000 overlaps existing 0xf0000000,0x4000000
agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
agpgart: reserved bits set in mode 0x1f00021f. Fixed.
agpgart: Xorg tried to set rate=x12. Setting to AGP3 x8 mode.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:05.0 into 8x mode
[drm] Loading R200 Microcode
    ACPI-0294: *** Error: Looking up [STAT] in namespace, AE_ALREADY_EXISTS
    ACPI-1138: *** Error: Method execution failed [\_SB_.PCI0.LPC0.BAT1._BIF] (Node dbf58300), AE_ALREADY_EXISTS
    ACPI-0294: *** Error: Looking up [PBST] in namespace, AE_ALREADY_EXISTS
    ACPI-1138: *** Error: Method execution failed [\_SB_.PCI0.LPC0.BAT1._BST] (Node dbf582e0), AE_ALREADY_EXISTS