mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
From: Daniel Mack <daniel@zonque.org>
To: Lech Perczak <lech.perczak@camlingroup.com>,
	Hugo Villeneuve <hugo@hugovil.com>
Cc: gregkh@linuxfoundation.org, jirislaby@kernel.org,
	u.kleine-koenig@pengutronix.de, linux-serial@vger.kernel.org,
	linux-kernel@vger.kernel.org, Maxim Popov <maxim.snafu@gmail.com>,
	stable@vger.kernel.org
Subject: Re: [PATCH] serial: sc16is7xx: address RX timeout interrupt errata
Date: Wed, 15 Nov 2023 12:22:10 +0100	[thread overview]
Message-ID: <ecc90a62-7cfa-45c9-9f6c-188e2c8ac50f@zonque.org> (raw)
In-Reply-To: <3fac7d72-0a1b-4d93-9245-a0f8af1240a6@camlingroup.com>

Hi Lech,

On 11/15/23 11:51, Lech Perczak wrote:
> W dniu 14.11.2023 o 16:55, Daniel Mack pisze:
>> Hi Hugo,
>>
>> On 11/14/23 16:20, Hugo Villeneuve wrote:
>>> On Tue, 14 Nov 2023 08:49:04 +0100
>>> Daniel Mack <daniel@zonque.org> wrote:
>>>> This devices has a silicon bug that makes it report a timeout interrupt
>>>> but no data in FIFO.
>>>>
>>>> The datasheet states the following in the errata section 18.1.4:
>>>>
>>>>   "If the host reads the receive FIFO at the at the same time as a
>>>>   time-out interrupt condition happens, the host might read 0xCC
>>>>   (time-out) in the Interrupt Indication Register (IIR), but bit 0
>>>>   of the Line Status Register (LSR) is not set (means there is not
>>>>   data in the receive FIFO)."
>>>>
>>>> When this happens, the loop in sc16is7xx_irq() will run forever,
>>>> which effectively blocks the i2c bus and breaks the functionality
>>>> of the UART.
>>>>
>>>> From the information above, it is assumed that when the bug is
>>>> triggered, the FIFO does in fact have payload in its buffer, but the
>>>> fill level reporting is off-by-one. Hence this patch fixes the issue
>>>> by reading one byte from the FIFO when that condition is detected.
>>> From what I understand from the errata, when the problem occurs, it
>>> affects bit 0 of the LSR register. I see no mention that it
>>> also affects the RX FIFO level register (SC16IS7XX_RXLVL_REG)?
>> True, the errata doesn't explicitly mention that, but tests have shown
>> that the RXLVL register is equally affected.
>>
>>> LSR[0] would be checked only if we were using polled mode of
>>> operation, but we always use the interrupt mode (IRQ), and therefore I
>>> would say that this errata doesn't apply to this driver, and the
>>> patch is not necessary...
>> Well, it is. We have seen this bug in the wild and extensively
>> stress-tested the patch on dozens of boards for many days. Without this
>> patch, kernels on affected systems would consume a lot of CPU cycles in
>> the interrupt threads and effectively render the I2C bus unusable due to
>> the busy polling.
>>
>> With this patch applied, we were no longer able to reproduce the issue.
> Could you share some more details on the setup you use to reproduce this? I'd like to try out as well.

We have boards with 2 I2C busses with an SC16IS752IBS on both. The UARTs
are configured in infrared mode, and they send receive IR signals
constantly. I guess the same would happen with other electrical
interfaces, but the important bit is that the UARTs see a steady stream
of inbound data.

The bug has hit us on production units and when it does, sc16is7xx_irq()
would spin forever because sc16is7xx_port_irq() keeps seeing an
interrupt in the IIR register that is not cleared because the driver
does not call into sc16is7xx_handle_rx() unless the RXLVL register
reports at least one byte in the FIFO.

Note that this issue might only occur in revision E of the silicon. And
there seems to be now way to read the revision code through I2C, so I
guess you won't be able to figure out easily whether your chip is affected.

Let me know if I can provide more information.


Thanks,
Daniel







  reply	other threads:[~2023-11-15 11:22 UTC|newest]

Thread overview: 12+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2023-11-14  7:49 Daniel Mack
2023-11-14 15:20 ` Hugo Villeneuve
2023-11-14 15:55   ` Daniel Mack
2023-11-15 10:51     ` Lech Perczak
2023-11-15 11:22       ` Daniel Mack [this message]
2023-11-15 15:01         ` Hugo Villeneuve
2023-11-15 15:12           ` Daniel Mack
2023-11-15 14:47     ` Hugo Villeneuve
2023-11-15 14:57       ` Daniel Mack
2023-11-15 15:31         ` Hugo Villeneuve
2023-11-15 15:38           ` Daniel Mack
2023-11-15 14:49 ` Hugo Villeneuve

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=ecc90a62-7cfa-45c9-9f6c-188e2c8ac50f@zonque.org \
    --to=daniel@zonque.org \
    --cc=gregkh@linuxfoundation.org \
    --cc=hugo@hugovil.com \
    --cc=jirislaby@kernel.org \
    --cc=lech.perczak@camlingroup.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-serial@vger.kernel.org \
    --cc=maxim.snafu@gmail.com \
    --cc=stable@vger.kernel.org \
    --cc=u.kleine-koenig@pengutronix.de \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®