mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
From: Daniel Golle <daniel@makrotopia.org>
To: "David S. Miller" <davem@davemloft.net>,
	Eric Dumazet <edumazet@google.com>,
	Jakub Kicinski <kuba@kernel.org>, Paolo Abeni <pabeni@redhat.com>,
	Rob Herring <robh@kernel.org>,
	Krzysztof Kozlowski <krzk+dt@kernel.org>,
	Conor Dooley <conor+dt@kernel.org>, Andrew Lunn <andrew@lunn.ch>,
	Heiner Kallweit <hkallweit1@gmail.com>,
	Russell King <linux@armlinux.org.uk>,
	Christian Marangi <ansuelsmth@gmail.com>,
	Bartosz Golaszewski <bartosz.golaszewski@linaro.org>,
	Daniel Golle <daniel@makrotopia.org>,
	Robert Marko <robimarko@gmail.com>,
	Russell King <rmk+kernel@armlinux.org.uk>,
	Chad Monroe <chad.monroe@adtran.com>,
	John Crispin <john@phrozen.org>,
	netdev@vger.kernel.org, devicetree@vger.kernel.org,
	linux-kernel@vger.kernel.org
Subject: [PATCH net-next 2/2] net: phy: aquantia: allow forcing order of MDI pairs
Date: Wed, 21 Aug 2024 13:46:50 +0100	[thread overview]
Message-ID: <ed46220cc4c52d630fc481c8148fc749242c368d.1724244281.git.daniel@makrotopia.org> (raw)
In-Reply-To: <5173302f9f1a52d7487e1fb54966673c448d6928.1724244281.git.daniel@makrotopia.org>

Normally, the MDI reversal configuration is taken from the MDI_CFG pin.
However, some hardware designs require overriding the value configured
by that bootstrap pin. The PHY allows doing that by setting a bit which
allows ignoring the state of the MDI_CFG pin and configuring whether
the order of MDI pairs should be normal (ABCD) or reverse (DCBA).

Introduce two boolean properties which allow forcing either normal or
reverse order of the MDI pairs from DT.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
---
 drivers/net/phy/aquantia/aquantia_main.c | 35 ++++++++++++++++++++++++
 1 file changed, 35 insertions(+)

diff --git a/drivers/net/phy/aquantia/aquantia_main.c b/drivers/net/phy/aquantia/aquantia_main.c
index e982e9ce44a59..33a6eb55d99d4 100644
--- a/drivers/net/phy/aquantia/aquantia_main.c
+++ b/drivers/net/phy/aquantia/aquantia_main.c
@@ -11,6 +11,7 @@
 #include <linux/module.h>
 #include <linux/delay.h>
 #include <linux/bitfield.h>
+#include <linux/of.h>
 #include <linux/phy.h>
 
 #include "aquantia.h"
@@ -71,6 +72,11 @@
 #define MDIO_AN_TX_VEND_INT_MASK2		0xd401
 #define MDIO_AN_TX_VEND_INT_MASK2_LINK		BIT(0)
 
+#define PMAPMD_RSVD_VEND_PROV			0xe400
+#define PMAPMD_RSVD_VEND_PROV_MDI_CONF		GENMASK(1, 0)
+#define PMAPMD_RSVD_VEND_PROV_MDI_REVERSE	BIT(0)
+#define PMAPMD_RSVD_VEND_PROV_MDI_FORCE		BIT(1)
+
 #define MDIO_AN_RX_LP_STAT1			0xe820
 #define MDIO_AN_RX_LP_STAT1_1000BASET_FULL	BIT(15)
 #define MDIO_AN_RX_LP_STAT1_1000BASET_HALF	BIT(14)
@@ -474,6 +480,31 @@ static void aqr107_chip_info(struct phy_device *phydev)
 		   fw_major, fw_minor, build_id, prov_id);
 }
 
+int aqr107_config_mdi(struct phy_device *phydev)
+{
+	struct device_node *np = phydev->mdio.dev.of_node;
+	bool force_normal, force_reverse;
+
+	force_normal = of_property_read_bool(np, "marvell,force-mdi-order-normal");
+	force_reverse = of_property_read_bool(np, "marvell,force-mdi-order-reverse");
+
+	if (force_normal && force_reverse)
+		return -EINVAL;
+
+	if (force_normal)
+		return phy_modify_mmd(phydev, MDIO_MMD_PMAPMD, PMAPMD_RSVD_VEND_PROV,
+				      PMAPMD_RSVD_VEND_PROV_MDI_CONF,
+				      PMAPMD_RSVD_VEND_PROV_MDI_FORCE);
+
+	if (force_reverse)
+		return phy_modify_mmd(phydev, MDIO_MMD_PMAPMD, PMAPMD_RSVD_VEND_PROV,
+				      PMAPMD_RSVD_VEND_PROV_MDI_CONF,
+				      PMAPMD_RSVD_VEND_PROV_MDI_REVERSE |
+				      PMAPMD_RSVD_VEND_PROV_MDI_FORCE);
+
+	return 0;
+}
+
 static int aqr107_config_init(struct phy_device *phydev)
 {
 	struct aqr107_priv *priv = phydev->priv;
@@ -503,6 +534,10 @@ static int aqr107_config_init(struct phy_device *phydev)
 	if (ret)
 		return ret;
 
+	ret = aqr107_config_mdi(phydev);
+	if (ret)
+		return ret;
+
 	/* Restore LED polarity state after reset */
 	for_each_set_bit(led_active_low, &priv->leds_active_low, AQR_MAX_LEDS) {
 		ret = aqr_phy_led_active_low_set(phydev, index, led_active_low);
-- 
2.46.0

  reply	other threads:[~2024-08-21 12:47 UTC|newest]

Thread overview: 13+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2024-08-21 12:46 [PATCH net-next 1/2] dt-bindings: net: marvell,aquantia: add properties to override MDI_CFG Daniel Golle
2024-08-21 12:46 ` Daniel Golle [this message]
2024-08-21 16:07   ` [PATCH net-next 2/2] net: phy: aquantia: allow forcing order of MDI pairs Andrew Lunn
2024-08-21 16:18     ` Daniel Golle
2024-08-23  1:28       ` Andrew Lunn
2024-08-27 15:15         ` Daniel Golle
2024-08-22  6:51   ` kernel test robot
2024-08-22  7:54   ` kernel test robot
2024-08-22  8:04   ` kernel test robot
2024-08-21 15:51 ` [PATCH net-next 1/2] dt-bindings: net: marvell,aquantia: add properties to override MDI_CFG Conor Dooley
2024-08-21 16:00 ` Andrew Lunn
2024-08-21 16:08   ` Daniel Golle
2024-08-21 16:13     ` Andrew Lunn

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=ed46220cc4c52d630fc481c8148fc749242c368d.1724244281.git.daniel@makrotopia.org \
    --to=daniel@makrotopia.org \
    --cc=andrew@lunn.ch \
    --cc=ansuelsmth@gmail.com \
    --cc=bartosz.golaszewski@linaro.org \
    --cc=chad.monroe@adtran.com \
    --cc=conor+dt@kernel.org \
    --cc=davem@davemloft.net \
    --cc=devicetree@vger.kernel.org \
    --cc=edumazet@google.com \
    --cc=hkallweit1@gmail.com \
    --cc=john@phrozen.org \
    --cc=krzk+dt@kernel.org \
    --cc=kuba@kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux@armlinux.org.uk \
    --cc=netdev@vger.kernel.org \
    --cc=pabeni@redhat.com \
    --cc=rmk+kernel@armlinux.org.uk \
    --cc=robh@kernel.org \
    --cc=robimarko@gmail.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®