Re: [PATCH] iio: light: bh1750: Add hardware reset support via GPIO

["Sergio Pérez" <sergio@pereznus.es>]

Hello,

El 17/03/2025 a las 8:24, Krzysztof Kozlowski escribió:
> On 16/03/2025 15:55, Sergio Perez wrote:
>> Some BH1750 sensors require a hardware reset before they can be
>> detected on the I2C bus. This patch adds support for an optional
>> reset GPIO that can be specified in the device tree.
>>
>> The reset sequence pulls the GPIO low and then high before
>> initializing the sensor, which enables proper detection with
>> tools like i2cdetect.
>>
>> Update the devicetree binding documentation to include the new
>> reset-gpios property with examples.
>>
>> Signed-off-by: Sergio Perez <sergio@pereznus.es>
> Please run scripts/checkpatch.pl and fix reported warnings. After that,
> run also `scripts/checkpatch.pl --strict` and (probably) fix more
> warnings. Some warnings can be ignored, especially from --strict run,
> but the code here looks like it needs a fix. Feel free to get in touch
> if the warning is not clear.
>
> <form letter>
> Please use scripts/get_maintainers.pl to get a list of necessary people
> and lists to CC. It might happen, that command when run on an older
> kernel, gives you outdated entries. Therefore please be sure you base
> your patches on recent Linux kernel.
>
> Tools like b4 or scripts/get_maintainer.pl provide you proper list of
> people, so fix your workflow. Tools might also fail if you work on some
> ancient tree (don't, instead use mainline) or work on fork of kernel
> (don't, instead use mainline). Just use b4 and everything should be
> fine, although remember about `b4 prep --auto-to-cc` if you added new
> patches to the patchset.
>
> You missed at least devicetree list (maybe more), so this won't be
> tested by automated tooling. Performing review on untested code might be
> a waste of time.
>
> Please kindly resend and include all necessary To/Cc entries.
> </form letter>
>

Sorry, I had run the scripts/get_maintainer.pl tool and got fewer 
recipients than necessary.  I have redone everything in a clean 
installation and now I have obtained more recipients.

Any fixes I make in the patch I send to this same thread or should I 
send it with git send-mail? I say this because perhaps I have done it 
incorrectly and possibly created 3 versions, I apologize. My latest 
version (v3) includes all the suggestions mentioned but due to my 
ignorance of the procedure I thought they should be sent to the list 
again as before. Can I delete v2 and v3 and keep only the first version?

>> ---
>>   .../devicetree/bindings/iio/light/bh1750.yaml |  20 +++-
>>   drivers/iio/light/bh1750.c                    | 113 ++++++++++++------
>
> ... and please go through your patch and see what happened there.
>>   2 files changed, 95 insertions(+), 38 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/iio/light/bh1750.yaml b/Documentation/devicetree/bindings/iio/light/bh1750.yaml
>> index 1a88b3c253d5..d53b221eb84b 100644
>> --- a/Documentation/devicetree/bindings/iio/light/bh1750.yaml
>> +++ b/Documentation/devicetree/bindings/iio/light/bh1750.yaml
>> @@ -11,6 +11,9 @@ maintainers:
>>   
>>   description: |
>>     Ambient light sensor with an i2c interface.
>> +
>> +  Some BH1750 sensors require a hardware reset before being properly detected
>> +  on the I2C bus. This can be done using the optional reset-gpios property.
>>   
>>   properties:
>>     compatible:
>> @@ -23,6 +26,10 @@ properties:
>>   
>>     reg:
>>       maxItems: 1
>> +
>> +  reset-gpios:
>> +    description: GPIO connected to the sensor's reset line (active low)
>> +    maxItems: 1
>>   
>>   required:
>>     - compatible
>> @@ -41,5 +48,16 @@ examples:
>>           reg = <0x23>;
>>         };
>>       };
>> +  - |
>> +    i2c {
>> +      #address-cells = <1>;
>> +      #size-cells = <0>;
>> +
>> +      light-sensor@23 {
>> +        compatible = "rohm,bh1750";
>> +        reg = <0x23>;
>> +        reset-gpios = <&gpio2 17 GPIO_ACTIVE_HIGH>;
>> +      };
>> +    };
>>   
>> -...
>> +...
>> \ No newline at end of file
> You have unrelated changed all over the place.
>
>
> Best regards,
> Krzysztof

Yes, in the patch I have prepared I have solved this problem, it only 
adds the exact lines and does not modify anything else.