mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
From: "Christian König" <christian.koenig@amd.com>
To: Liao Yuanhong <liaoyuanhong@vivo.com>,
	Tvrtko Ursulin <tursulin@ursulin.net>
Cc: Alex Deucher <alexander.deucher@amd.com>,
	David Airlie <airlied@gmail.com>, Simona Vetter <simona@ffwll.ch>,
	"open list:RADEON and AMDGPU DRM DRIVERS"
	<amd-gfx@lists.freedesktop.org>,
	"open list:DRM DRIVERS" <dri-devel@lists.freedesktop.org>,
	open list <linux-kernel@vger.kernel.org>
Subject: Re: [PATCH] drm/radeon: Move the memset() function call after the return statement
Date: Thu, 14 Aug 2025 14:29:14 +0200	[thread overview]
Message-ID: <f0d58122-5958-4c93-b1a7-daa229a723b6@amd.com> (raw)
In-Reply-To: <6ef5e1e8-3868-46c0-a31b-505f8a91d37a@vivo.com>

On 14.08.25 13:56, Liao Yuanhong wrote:
> On 8/14/2025 7:07 PM, Tvrtko Ursulin wrote:
> 
>>
>> On 14/08/2025 11:11, Christian König wrote:
>>> On 14.08.25 11:39, Liao Yuanhong wrote:
>>>> Adjust the position of the memset() call to avoid unnecessary invocations.
>>>
>>> Hui? That doesn't seem to make much sense to me.
>>>
>>> We memset the local variable because we need to make sure that everything (including padding bytes) is zeroed out.
>>>
>>> Even if that isn't sometimes necessary because of error handling we clearly shouldn't try to optimize this.
>>
>> To interject with a curiousity, it is even worse to move the memset away from the declaration block when the often enabled CONFIG_INIT_STACK_ALL_ZERO is on. At least when they are close compiler can figure out it only needs to memset it once. Move them further apart and sometimes memset happens twice, yay.
>>
>> Main point when CONFIG_INIT_STACK_ALL_ZERO is on, and it often is, there is no way to avoid the sometimes pointless init. I have some local branches which try to address the worst offenders but it is so much in the noise that I don't think I ever sent them out.
>>
>> Regards,
>>
>> Tvrtko
>>
> If we converts memset() to = { },can it alleviate the problem?

No, memset is intentionally used here to make sure we set all bytes to zero. Including padding.

Regards,
Christian.

> 
> 
> Thanks,
> 
> Liao
> 
>>>> Signed-off-by: Liao Yuanhong <liaoyuanhong@vivo.com>
>>>> ---
>>>>   drivers/gpu/drm/radeon/atombios_crtc.c     |  8 ++++----
>>>>   drivers/gpu/drm/radeon/atombios_encoders.c | 20 ++++++++++----------
>>>>   2 files changed, 14 insertions(+), 14 deletions(-)
>>>>
>>>> diff --git a/drivers/gpu/drm/radeon/atombios_crtc.c b/drivers/gpu/drm/radeon/atombios_crtc.c
>>>> index 9b3a3a9d60e2..0aae84f5e27c 100644
>>>> --- a/drivers/gpu/drm/radeon/atombios_crtc.c
>>>> +++ b/drivers/gpu/drm/radeon/atombios_crtc.c
>>>> @@ -770,13 +770,13 @@ static void atombios_crtc_set_disp_eng_pll(struct radeon_device *rdev,
>>>>       int index;
>>>>       union set_pixel_clock args;
>>>>   -    memset(&args, 0, sizeof(args));
>>>> -
>>>>       index = GetIndexIntoMasterTable(COMMAND, SetPixelClock);
>>>>       if (!atom_parse_cmd_header(rdev->mode_info.atom_context, index, &frev,
>>>>                      &crev))
>>>>           return;
>>>>   +    memset(&args, 0, sizeof(args));
>>>> +
>>>>       switch (frev) {
>>>>       case 1:
>>>>           switch (crev) {
>>>> @@ -832,12 +832,12 @@ static void atombios_crtc_program_pll(struct drm_crtc *crtc,
>>>>       int index = GetIndexIntoMasterTable(COMMAND, SetPixelClock);
>>>>       union set_pixel_clock args;
>>>>   -    memset(&args, 0, sizeof(args));
>>>> -
>>>>       if (!atom_parse_cmd_header(rdev->mode_info.atom_context, index, &frev,
>>>>                      &crev))
>>>>           return;
>>>>   +    memset(&args, 0, sizeof(args));
>>>> +
>>>>       switch (frev) {
>>>>       case 1:
>>>>           switch (crev) {
>>>> diff --git a/drivers/gpu/drm/radeon/atombios_encoders.c b/drivers/gpu/drm/radeon/atombios_encoders.c
>>>> index d1c5e471bdca..f706e21a3509 100644
>>>> --- a/drivers/gpu/drm/radeon/atombios_encoders.c
>>>> +++ b/drivers/gpu/drm/radeon/atombios_encoders.c
>>>> @@ -492,11 +492,11 @@ atombios_dvo_setup(struct drm_encoder *encoder, int action)
>>>>       int index = GetIndexIntoMasterTable(COMMAND, DVOEncoderControl);
>>>>       uint8_t frev, crev;
>>>>   -    memset(&args, 0, sizeof(args));
>>>> -
>>>>       if (!atom_parse_cmd_header(rdev->mode_info.atom_context, index, &frev, &crev))
>>>>           return;
>>>>   +    memset(&args, 0, sizeof(args));
>>>> +
>>>>       /* some R4xx chips have the wrong frev */
>>>>       if (rdev->family <= CHIP_RV410)
>>>>           frev = 1;
>>>> @@ -856,8 +856,6 @@ atombios_dig_encoder_setup2(struct drm_encoder *encoder, int action, int panel_m
>>>>       if (dig->dig_encoder == -1)
>>>>           return;
>>>>   -    memset(&args, 0, sizeof(args));
>>>> -
>>>>       if (ASIC_IS_DCE4(rdev))
>>>>           index = GetIndexIntoMasterTable(COMMAND, DIGxEncoderControl);
>>>>       else {
>>>> @@ -870,6 +868,8 @@ atombios_dig_encoder_setup2(struct drm_encoder *encoder, int action, int panel_m
>>>>       if (!atom_parse_cmd_header(rdev->mode_info.atom_context, index, &frev, &crev))
>>>>           return;
>>>>   +    memset(&args, 0, sizeof(args));
>>>> +
>>>>       switch (frev) {
>>>>       case 1:
>>>>           switch (crev) {
>>>> @@ -1453,11 +1453,11 @@ atombios_external_encoder_setup(struct drm_encoder *encoder,
>>>>               (radeon_connector->connector_object_id & OBJECT_ID_MASK) >> OBJECT_ID_SHIFT;
>>>>       }
>>>>   -    memset(&args, 0, sizeof(args));
>>>> -
>>>>       if (!atom_parse_cmd_header(rdev->mode_info.atom_context, index, &frev, &crev))
>>>>           return;
>>>>   +    memset(&args, 0, sizeof(args));
>>>> +
>>>>       switch (frev) {
>>>>       case 1:
>>>>           /* no params on frev 1 */
>>>> @@ -1853,11 +1853,11 @@ atombios_set_encoder_crtc_source(struct drm_encoder *encoder)
>>>>       uint8_t frev, crev;
>>>>       struct radeon_encoder_atom_dig *dig;
>>>>   -    memset(&args, 0, sizeof(args));
>>>> -
>>>>       if (!atom_parse_cmd_header(rdev->mode_info.atom_context, index, &frev, &crev))
>>>>           return;
>>>>   +    memset(&args, 0, sizeof(args));
>>>> +
>>>>       switch (frev) {
>>>>       case 1:
>>>>           switch (crev) {
>>>> @@ -2284,11 +2284,11 @@ atombios_dac_load_detect(struct drm_encoder *encoder, struct drm_connector *conn
>>>>           int index = GetIndexIntoMasterTable(COMMAND, DAC_LoadDetection);
>>>>           uint8_t frev, crev;
>>>>   -        memset(&args, 0, sizeof(args));
>>>> -
>>>>           if (!atom_parse_cmd_header(rdev->mode_info.atom_context, index, &frev, &crev))
>>>>               return false;
>>>>   +        memset(&args, 0, sizeof(args));
>>>> +
>>>>           args.sDacload.ucMisc = 0;
>>>>             if ((radeon_encoder->encoder_id == ENCODER_OBJECT_ID_INTERNAL_DAC1) ||
>>>
>>


      parent reply	other threads:[~2025-08-14 12:29 UTC|newest]

Thread overview: 7+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2025-08-14  9:39 Liao Yuanhong
2025-08-14 10:11 ` Christian König
2025-08-14 11:07   ` Tvrtko Ursulin
2025-08-14 11:56     ` Liao Yuanhong
2025-08-14 12:10       ` Tvrtko Ursulin
2025-08-14 12:32         ` Christian König
2025-08-14 12:29       ` Christian König [this message]

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=f0d58122-5958-4c93-b1a7-daa229a723b6@amd.com \
    --to=christian.koenig@amd.com \
    --cc=airlied@gmail.com \
    --cc=alexander.deucher@amd.com \
    --cc=amd-gfx@lists.freedesktop.org \
    --cc=dri-devel@lists.freedesktop.org \
    --cc=liaoyuanhong@vivo.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=simona@ffwll.ch \
    --cc=tursulin@ursulin.net \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®