From: Jyri Sarha <jsarha@ti.com>
To: Bartosz Golaszewski <bgolaszewski@baylibre.com>,
Tomi Valkeinen <tomi.valkeinen@ti.com>,
David Airlie <airlied@linux.ie>,
Kevin Hilman <khilman@baylibre.com>,
Michael Turquette <mturquette@baylibre.com>,
Sekhar Nori <nsekhar@ti.com>
Cc: LKML <linux-kernel@vger.kernel.org>,
linux-drm <dri-devel@lists.freedesktop.org>,
Peter Ujfalusi <peter.ujfalusi@ti.com>,
arm-soc <linux-arm-kernel@lists.infradead.org>
Subject: Re: [PATCH v5 2/2] drm: tilcdc: clear the sync lost bit in crtc isr
Date: Tue, 1 Nov 2016 16:25:03 +0200 [thread overview]
Message-ID: <f26ad056-8cf7-41b8-c80b-1c564ebe51a3@ti.com> (raw)
In-Reply-To: <1477923567-1610-3-git-send-email-bgolaszewski@baylibre.com>
On 10/31/16 16:19, Bartosz Golaszewski wrote:
> The frame synchronization error happens when the DMA engine attempts
> to read what it believes to be the first word of the video buffer but
> it cannot be recognized as such or when the LCDC is starved of data
> due to insufficient bandwidth of the system interconnect.
>
> On some SoCs (notably: da850) the memory settings do not meet the
> LCDC throughput requirements even after increasing the memory
> controller command re-ordering and the LDCD master peripheral
> priority, sometimes causing the sync lost error (typically when
> changing the resolution).
>
> When the sync lost error occurs, simply reset the input FIFO in the
> DMA controller unless a sync lost flood is detected in which case
> disable the interrupt.
>
> Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
> ---
> drivers/gpu/drm/tilcdc/tilcdc_crtc.c | 50 ++++++++++++++++++++++++++----------
> drivers/gpu/drm/tilcdc/tilcdc_regs.h | 1 +
> 2 files changed, 37 insertions(+), 14 deletions(-)
>
> diff --git a/drivers/gpu/drm/tilcdc/tilcdc_crtc.c b/drivers/gpu/drm/tilcdc/tilcdc_crtc.c
> index 937697d..c4c6323 100644
> --- a/drivers/gpu/drm/tilcdc/tilcdc_crtc.c
> +++ b/drivers/gpu/drm/tilcdc/tilcdc_crtc.c
> @@ -163,7 +163,7 @@ static void tilcdc_crtc_enable_irqs(struct drm_device *dev)
>
> if (priv->rev == 1) {
> tilcdc_set(dev, LCDC_RASTER_CTRL_REG,
> - LCDC_V1_UNDERFLOW_INT_ENA);
> + LCDC_V1_UNDERFLOW_INT_ENA | LCDC_V1_SYNC_LOST_ENA);
> tilcdc_set(dev, LCDC_DMA_CTRL_REG,
> LCDC_V1_END_OF_FRAME_INT_ENA);
> } else {
> @@ -181,7 +181,9 @@ static void tilcdc_crtc_disable_irqs(struct drm_device *dev)
> /* disable irqs that we might have enabled: */
> if (priv->rev == 1) {
> tilcdc_clear(dev, LCDC_RASTER_CTRL_REG,
> - LCDC_V1_UNDERFLOW_INT_ENA | LCDC_V1_PL_INT_ENA);
> + LCDC_V1_UNDERFLOW_INT_ENA |
> + LCDC_V1_PL_INT_ENA |
> + LCDC_V1_SYNC_LOST_ENA);
> tilcdc_clear(dev, LCDC_DMA_CTRL_REG,
> LCDC_V1_END_OF_FRAME_INT_ENA);
> } else {
> @@ -885,24 +887,44 @@ irqreturn_t tilcdc_crtc_irq(struct drm_crtc *crtc)
> wake_up(&tilcdc_crtc->frame_done_wq);
> }
>
> - if (stat & LCDC_SYNC_LOST) {
> - dev_err_ratelimited(dev->dev, "%s(0x%08x): Sync lost",
> - __func__, stat);
> - tilcdc_crtc->frame_intact = false;
> - if (tilcdc_crtc->sync_lost_count++ >
> - SYNC_LOST_COUNT_LIMIT) {
> - dev_err(dev->dev, "%s(0x%08x): Sync lost flood detected, disabling the interrupt", __func__, stat);
> - tilcdc_write(dev, LCDC_INT_ENABLE_CLR_REG,
> - LCDC_SYNC_LOST);
> - }
> - }
> -
> /* Indicate to LCDC that the interrupt service routine has
> * completed, see 13.3.6.1.6 in AM335x TRM.
> */
> tilcdc_write(dev, LCDC_END_OF_INT_IND_REG, 0);
Oh, I think this should the last thing done in the irq routine, thought
I do not really know what it does :).
> }
>
> + if (stat & LCDC_SYNC_LOST) {
> + dev_err_ratelimited(dev->dev, "%s(0x%08x): Sync lost",
> + __func__, stat);
> +
> + tilcdc_crtc->frame_intact = false;
> + if (tilcdc_crtc->sync_lost_count++ > SYNC_LOST_COUNT_LIMIT) {
> + dev_err(dev->dev,
> + "%s(0x%08x): Sync lost flood detected, disabling the interrupt",
> + __func__, stat);
> + if (priv->rev == 2)
> + tilcdc_write(dev, LCDC_INT_ENABLE_CLR_REG,
> + LCDC_SYNC_LOST);
> + else if (priv->rev == 1)
> + tilcdc_clear(dev, LCDC_RASTER_CTRL_REG,
> + LCDC_V1_SYNC_LOST_ENA);
> + }
> +
> + if (priv->rev == 2) {
> + /*
> + * Indicate to LCDC that the interrupt service routine
> + * has completed, see 13.3.6.1.6 in AM335x TRM.
> + */
> + tilcdc_write(dev, LCDC_END_OF_INT_IND_REG, 0);
> + } else if (priv->rev == 1) {
> + /* Reset the input FIFO in the DMA controller. */
> + tilcdc_clear(dev,
> + LCDC_RASTER_CTRL_REG, LCDC_RASTER_ENABLE);
> + tilcdc_set(dev,
> + LCDC_RASTER_CTRL_REG, LCDC_RASTER_ENABLE);
> + }
> + }
> +
> return IRQ_HANDLED;
> }
>
> diff --git a/drivers/gpu/drm/tilcdc/tilcdc_regs.h b/drivers/gpu/drm/tilcdc/tilcdc_regs.h
> index f57c0d6..beb8c21 100644
> --- a/drivers/gpu/drm/tilcdc/tilcdc_regs.h
> +++ b/drivers/gpu/drm/tilcdc/tilcdc_regs.h
> @@ -61,6 +61,7 @@
> #define LCDC_V2_UNDERFLOW_INT_ENA BIT(5)
> #define LCDC_V1_PL_INT_ENA BIT(4)
> #define LCDC_V2_PL_INT_ENA BIT(6)
> +#define LCDC_V1_SYNC_LOST_ENA BIT(5)
> #define LCDC_MONOCHROME_MODE BIT(1)
> #define LCDC_RASTER_ENABLE BIT(0)
> #define LCDC_TFT_ALT_ENABLE BIT(23)
>
prev parent reply other threads:[~2016-11-01 14:25 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-10-31 14:19 [PATCH v5 0/2] drm: tilcdc: improved support for rev1 Bartosz Golaszewski
2016-10-31 14:19 ` [PATCH v5 1/2] drm: tilcdc: implement palette loading " Bartosz Golaszewski
2016-10-31 16:05 ` Jyri Sarha
2016-11-16 11:34 ` Bartosz Golaszewski
2016-11-16 14:40 ` Jyri Sarha
2016-10-31 14:19 ` [PATCH v5 2/2] drm: tilcdc: clear the sync lost bit in crtc isr Bartosz Golaszewski
2016-10-31 16:32 ` Karl Beldan
2016-11-01 14:22 ` Jyri Sarha
2016-11-01 14:25 ` Jyri Sarha [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=f26ad056-8cf7-41b8-c80b-1c564ebe51a3@ti.com \
--to=jsarha@ti.com \
--cc=airlied@linux.ie \
--cc=bgolaszewski@baylibre.com \
--cc=dri-devel@lists.freedesktop.org \
--cc=khilman@baylibre.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mturquette@baylibre.com \
--cc=nsekhar@ti.com \
--cc=peter.ujfalusi@ti.com \
--cc=tomi.valkeinen@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®