Re: [PATCH V2 3/8] clk: qcom: Add Global Clock controller (GCC) driver for IPQ5018

[Sricharan Ramabadhran <quic_srichara@quicinc.com>]

On 6/24/2022 9:35 AM, Bjorn Andersson wrote:
> On Tue 21 Jun 11:11 CDT 2022, Sricharan R wrote:
>> diff --git a/drivers/clk/qcom/gcc-ipq5018.c b/drivers/clk/qcom/gcc-ipq5018.c
> [..]
>> +static const struct clk_parent_data gcc_xo_gpll0_gpll0_out_main_div2[] = {
>> +	{ .fw_name = "xo", .name = "xo", },
> Please replace .fw_name with .index based lookup, in line with what was
> done in gcc-sc8280xp.c recently.


  Sure, understand will fix it.

>
> There's no reason to include global name lookup (.name) in new drivers,
> so please omit this part.

   ok.


>> +	{ .fw_name = "gpll0", .name = "gpll0", },
>> +	{ .fw_name = "gpll0_out_main_div2", .name = "gpll0_out_main_div2", },
>> +};
>> +
> [..]
>> +static struct clk_alpha_pll gpll0_main = {
>> +	.offset = 0x21000,
>> +	.regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_DEFAULT],
>> +	.clkr = {
>> +		.enable_reg = 0x0b000,
>> +		.enable_mask = BIT(0),
>> +		.hw.init = &(struct clk_init_data){
>> +			.name = "gpll0_main",
>> +			.parent_data = &(const struct clk_parent_data){
>> +				.fw_name = "xo",
>> +				.name = "xo",
> Are you referring to the board XO here, or the CXO pin on the SoC? On
> many platforms these are not the same...
   board XO, will refer your above example and fix it here as well
> Please omit the .name here as well and as this is used a few times,
> please create a struct clk_parent_data for this parent.

   ok.


>> +			},
>> +			.num_parents = 1,
>> +			.ops = &clk_alpha_pll_stromer_ops,
>> +			.flags = CLK_IS_CRITICAL,
>> +		},
>> +	},
>> +};
>> +
>> +static struct clk_fixed_factor gpll0_out_main_div2 = {
>> +	.mult = 1,
>> +	.div = 2,
>> +	.hw.init = &(struct clk_init_data){
>> +		.name = "gpll0_out_main_div2",
>> +		.parent_data = &(const struct clk_parent_data){
> It would be nice to have a space inbetween ) and { in all these.

   ok.


>> +			.fw_name = "gpll0_main",
>> +			.name = "gpll0_main",
>> +		},
>> +		.num_parents = 1,
>> +		.ops = &clk_fixed_factor_ops,
>> +		.flags = CLK_SET_RATE_PARENT,
>> +	},
>> +};
> [..]
>> +static struct clk_branch gcc_gephy_tx_clk = {
>> +	.halt_reg = 0x56014,
>> +	.halt_check = BRANCH_HALT_DELAY,
>> +	.clkr = {
>> +		.enable_reg = 0x56014,
>> +		.enable_mask = BIT(0),
>> +		.hw.init = &(struct clk_init_data){
>> +			.name = "gcc_gephy_tx_clk",
>> +			.parent_data = &(const struct clk_parent_data){
>> +				.fw_name = "gmac0_tx_div_clk_src",
>> +				.name = "gmac0_tx_div_clk_src",
>> +			},
> This parent_data is repeated multiple times, but more importantly it's
> not an external clock, so you should use .parent_hw instead of
> .parent_data.
>
> Please review the parent for all your clocks.

   ok, will do.

Regards,
   Sricharan