mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
From: "Shah, Tanmay" <tanmays@amd.com>
To: Mathieu Poirier <mathieu.poirier@linaro.org>,
	Tanmay Shah <tanmay.shah@amd.com>
Cc: <andersson@kernel.org>, <linux-remoteproc@vger.kernel.org>,
	<linux-kernel@vger.kernel.org>
Subject: Re: [PATCH v5 2/2] remoteproc: xlnx: add crash detection mechanism
Date: Tue, 16 Jun 2026 14:52:50 -0500	[thread overview]
Message-ID: <f4809485-91d8-49c2-bed9-0d3bd0172cff@amd.com> (raw)
In-Reply-To: <ajFzbDgrCbWL8-ds@p14s>

Hello,

Please find my comments below:

On 6/16/2026 11:01 AM, Mathieu Poirier wrote:
> On Wed, Jun 10, 2026 at 11:27:11AM -0700, Tanmay Shah wrote:
>> Remote processor will report the crash reason via the resource table
>> and notify the host via mailbox notification. The host checks this
>> crash reason on every mailbox notification from the remote and report
>> to the rproc core framework. Then the rproc core framework will start
>> the recovery process.
>>
>> Signed-off-by: Tanmay Shah <tanmay.shah@amd.com>
>> ---
>>
>> changes in v5
>>   - use local variable to access crash report pointer
>>   - End crash report string with '\0' without relying on fw
>>
>>  drivers/remoteproc/xlnx_r5_remoteproc.c | 73 ++++++++++++++++++++++++-
>>  1 file changed, 72 insertions(+), 1 deletion(-)
>>
>> diff --git a/drivers/remoteproc/xlnx_r5_remoteproc.c b/drivers/remoteproc/xlnx_r5_remoteproc.c
>> index 3349d1877751..86afff9f3b40 100644
>> --- a/drivers/remoteproc/xlnx_r5_remoteproc.c
>> +++ b/drivers/remoteproc/xlnx_r5_remoteproc.c
>> @@ -112,6 +112,10 @@ struct rsc_tbl_data {
>>  	const uintptr_t rsc_tbl;
>>  } __packed;
>>  
>> +enum xlnx_rproc_fw_rsc {
>> +	XLNX_RPROC_FW_CRASH_REASON = RSC_VENDOR_START,
> 
> I would call this XLNX_RPROC_FW_CRASH_REPORT
> 

Ack.

>> +};
>> +
>>  /*
>>   * Hardcoded TCM bank values. This will stay in driver to maintain backward
>>   * compatibility with device-tree that does not have TCM information.
>> @@ -131,9 +135,27 @@ static const struct mem_bank_data zynqmp_tcm_banks_lockstep[] = {
>>  	{0xffe30000UL, 0x30000, 0x10000UL, PD_R5_1_BTCM, "btcm1"},
>>  };
>>  
>> +#define CRASH_REASON_STR_LEN 16
>> +
>> +/**
>> + * struct xlnx_rproc_crash_report - resource to know crash status and reason
>> + *
>> + * @version: version of this resource
>> + * @crash_state: if true, the rproc is notifying crash, time to recover
>> + * @crash_reason: number to describe reason of crash
>> + * @crash_reason_str: short string description of crash reason
>> + */
>> +struct xlnx_rproc_crash_report {
>> +	u8 version;
>> +	u8 crash_state;
>> +	u8 crash_reason;
> 
> Do you need 2 variables?  Would it be possible for @crash_reason != 0 to
> indicate a crash, making @cash_state irrelevant?
> 

Actually initially I had defined crash_reason only, but when I looked at
how crash reason/type is defined in the kernel, I got idea to keep
crash_state separate than crash_reason:

https://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux.git/tree/include/linux/remoteproc.h?h=for-next#n183

enum rproc_crash_type {
	RPROC_MMUFAULT,
	RPROC_WATCHDOG,
	RPROC_FATAL_ERROR,
};

So, if crash_reason is defined like above, then it's easy to make
mistake and not define no_crash = 0. Different firmware projects can
treat crash_reason differently. I would like to keep crash_state and
crash_reason separate and not impose policy on firmware projects on how
to define crash_reason.

>> +	char crash_reason_str[CRASH_REASON_STR_LEN];
>> +} __packed;
>> +
>>  /**
>>   * struct zynqmp_r5_core - remoteproc core's internal data
>>   *
>> + * @crash_report: rproc crash state and reason
>>   * @rsc_tbl_va: resource table virtual address
>>   * @sram: Array of sram memories assigned to this core
>>   * @num_sram: number of sram for this core
>> @@ -147,6 +169,7 @@ static const struct mem_bank_data zynqmp_tcm_banks_lockstep[] = {
>>   * @ipi: pointer to mailbox information
>>   */
>>  struct zynqmp_r5_core {
>> +	struct xlnx_rproc_crash_report *crash_report;
>>  	void __iomem *rsc_tbl_va;
>>  	struct zynqmp_sram_bank *sram;
>>  	int num_sram;
>> @@ -204,11 +227,27 @@ static int event_notified_idr_cb(int id, void *ptr, void *data)
>>   */
>>  static void handle_event_notified(struct work_struct *work)
>>  {
>> +	struct xlnx_rproc_crash_report *report;
>> +	struct zynqmp_r5_core *r5_core;
>>  	struct mbox_info *ipi;
>>  	struct rproc *rproc;
>>  
>>  	ipi = container_of(work, struct mbox_info, mbox_work);
>>  	rproc = ipi->r5_core->rproc;
>> +	r5_core = ipi->r5_core;
>> +	report = r5_core->crash_report;
>> +
>> +	/* report crash only if expected */
>> +	if (report && report->crash_state) {
>> +		if (rproc->state == RPROC_ATTACHED || rproc->state == RPROC_RUNNING) {
>> +			report->crash_reason_str[CRASH_REASON_STR_LEN - 1] = '\0';
>> +			dev_warn(&rproc->dev, "crash reason id: %d %s\n",
>> +				 report->crash_reason, report->crash_reason_str);
>> +			rproc_report_crash(rproc, RPROC_FATAL_ERROR);
>> +			report->crash_state = false;
>> +			return;
>> +		}
>> +	}
>>  
>>  	/*
>>  	 * We only use IPI for interrupt. The RPU firmware side may or may
>> @@ -448,6 +487,13 @@ static int zynqmp_r5_rproc_stop(struct rproc *rproc)
>>  	if (ret)
>>  		dev_err(r5_core->dev, "core force power down failed\n");
>>  
>> +	/*
>> +	 * Clear attach on recovery flag during stop operation. The next state
>> +	 * of the remote processor is expected to be "Running" state. In this
>> +	 * state boot recovery method must take place over attach on recovery.
>> +	 */
>> +	test_and_clear_bit(RPROC_FEAT_ATTACH_ON_RECOVERY, rproc->features);
> 
> Why is there a need to play set/clear the RPROC_FEAT_ATTACH_ON_RECOVERY flag
> here and in zynqmp_r5_attach() and zynqmp_r5_detach()?  I think we talked about
> that before but can't remember the outcome of that conversation.
> 

The remote processor can go through following life cycle:

attach() -> stop() -> start(). When this happens, ATTACH_ON_RECOVERY is
not valid anymore. At this point, it should be BOOT_RECOVERY which is
indicated by clearing ATTACH_RECOVERY flag. That is why it is important
to clear this bit on stop().

Now in detach() it is not needed. I am just clearing the flag as part of
a cleanup sequence.

 >> +
>>  	return ret;
>>  }
>>  
>> @@ -869,6 +915,9 @@ static int zynqmp_r5_get_rsc_table_va(struct zynqmp_r5_core *r5_core)
>>  
>>  static int zynqmp_r5_attach(struct rproc *rproc)
>>  {
>> +	/* Enable attach on recovery method. Clear it during rproc stop. */
>> +	rproc_set_feature(rproc, RPROC_FEAT_ATTACH_ON_RECOVERY);
>> +
>>  	dev_dbg(&rproc->dev, "rproc %d attached\n", rproc->index);
>>  
>>  	return 0;
>> @@ -883,9 +932,30 @@ static int zynqmp_r5_detach(struct rproc *rproc)
>>  	 */
>>  	zynqmp_r5_rproc_kick(rproc, 0);
>>  
>> +	clear_bit(RPROC_FEAT_ATTACH_ON_RECOVERY, rproc->features);
>> +
>>  	return 0;
>>  }
>>  
>> +static int zynqmp_r5_handle_rsc(struct rproc *rproc, u32 rsc_type, void *rsc,
>> +				int offset, int avail)
>> +{
>> +	struct zynqmp_r5_core *r5_core = rproc->priv;
>> +	void *rsc_offset = (r5_core->rsc_tbl_va + offset);
>> +
> 
>         if (rsc_type != XLNX_RPROC_FW_CRASH_REASON)
>                 return RSC_IGNORED;
> 

Ack.

>> +	if (rsc_type == XLNX_RPROC_FW_CRASH_REASON) {
>> +		r5_core->crash_report = rsc_offset;
>> +		/* reset all values */
>> +		r5_core->crash_report->crash_state = false;
>> +		r5_core->crash_report->crash_reason = 0;
>> +		r5_core->crash_report->crash_reason_str[0] = '\0';
>> +	} else {
>> +		return RSC_IGNORED;
>> +	}
>> +
>> +	return RSC_HANDLED;
>> +}
>> +
>>  static const struct rproc_ops zynqmp_r5_rproc_ops = {
>>  	.prepare	= zynqmp_r5_rproc_prepare,
>>  	.unprepare	= zynqmp_r5_rproc_unprepare,
>> @@ -900,6 +970,7 @@ static const struct rproc_ops zynqmp_r5_rproc_ops = {
>>  	.get_loaded_rsc_table = zynqmp_r5_get_loaded_rsc_table,
>>  	.attach		= zynqmp_r5_attach,
>>  	.detach		= zynqmp_r5_detach,
>> +	.handle_rsc	= zynqmp_r5_handle_rsc,
>>  };
>>  
>>  /**
>> @@ -939,7 +1010,7 @@ static struct zynqmp_r5_core *zynqmp_r5_alloc_rproc_core(struct device *cdev)
>>  
>>  	rproc_coredump_set_elf_info(r5_rproc, ELFCLASS32, EM_ARM);
>>  
>> -	r5_rproc->recovery_disabled = true;
>> +	r5_rproc->recovery_disabled = false;
> 
> I'm good with the overall architecture of this set.
> 

Okay. If above comments looks good, I will send v6 soon.

> Regards,
> Mathieu
> 
>>  	r5_rproc->has_iommu = false;
>>  	r5_rproc->auto_boot = false;
>>  
>> -- 
>> 2.34.1
>>


  reply	other threads:[~2026-06-16 19:52 UTC|newest]

Thread overview: 9+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2026-06-10 18:27 [PATCH v5 0/2] remoteproc: xlnx: remote crash recovery Tanmay Shah
2026-06-10 18:27 ` [PATCH v5 1/2] remoteproc: core: full attach detach during recovery Tanmay Shah
2026-06-16 15:29   ` Mathieu Poirier
2026-06-10 18:27 ` [PATCH v5 2/2] remoteproc: xlnx: add crash detection mechanism Tanmay Shah
2026-06-16 16:01   ` Mathieu Poirier
2026-06-16 19:52     ` Shah, Tanmay [this message]
2026-06-22 14:35       ` Mathieu Poirier
2026-06-22 17:46       ` Mathieu Poirier
2026-06-22 18:16         ` Shah, Tanmay

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=f4809485-91d8-49c2-bed9-0d3bd0172cff@amd.com \
    --to=tanmays@amd.com \
    --cc=andersson@kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-remoteproc@vger.kernel.org \
    --cc=mathieu.poirier@linaro.org \
    --cc=tanmay.shah@amd.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®