From: tip-bot for Thomas Gleixner <tipbot@zytor.com>
To: linux-tip-commits@vger.kernel.org
Cc: mingo@kernel.org, tglx@linutronix.de, pavel@ucw.cz,
linux-kernel@vger.kernel.org, hpa@zytor.com
Subject: [tip:x86/urgent] x86/apic: Switch all APICs to Fixed delivery mode
Date: Fri, 29 Dec 2017 05:31:53 -0800 [thread overview]
Message-ID: <tip-a31e58e129f73ab5b04016330b13ed51fde7a961@git.kernel.org> (raw)
In-Reply-To: <alpine.DEB.2.20.1712281140440.1688@nanos>
Commit-ID: a31e58e129f73ab5b04016330b13ed51fde7a961
Gitweb: https://git.kernel.org/tip/a31e58e129f73ab5b04016330b13ed51fde7a961
Author: Thomas Gleixner <tglx@linutronix.de>
AuthorDate: Thu, 28 Dec 2017 11:33:33 +0100
Committer: Thomas Gleixner <tglx@linutronix.de>
CommitDate: Fri, 29 Dec 2017 14:20:48 +0100
x86/apic: Switch all APICs to Fixed delivery mode
Some of the APIC incarnations are operating in lowest priority delivery
mode. This worked as long as the vector management code allocated the same
vector on all possible CPUs for each interrupt.
Lowest priority delivery mode does not necessarily respect the affinity
setting and may redirect to some other online CPU. This was documented
somewhere in the old code and the conversion to single target delivery
missed to update the delivery mode of the affected APIC drivers which
results in spurious interrupts on some of the affected CPU/Chipset
combinations.
Switch the APIC drivers over to Fixed delivery mode and remove all
leftovers of lowest priority delivery mode.
Switching to Fixed delivery mode is not a problem on these CPUs because the
kernel already uses Fixed delivery mode for IPIs. The reason for this is
that th SDM explicitely forbids lowest prio mode for IPIs. The reason is
obvious: If the irq routing does not honor destination targets in lowest
prio mode then an IPI targeted at CPU1 might end up on CPU0, which would be
a fatal problem in many cases.
As a consequence of this change, the apic::irq_delivery_mode field is now
pointless, but this needs to be cleaned up in a separate patch.
Fixes: fdba46ffb4c2 ("x86/apic: Get rid of multi CPU affinity")
Reported-by: vcaputo@pengaru.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: vcaputo@pengaru.com
Cc: Pavel Machek <pavel@ucw.cz>
Link: https://lkml.kernel.org/r/alpine.DEB.2.20.1712281140440.1688@nanos
---
arch/x86/kernel/apic/apic_flat_64.c | 2 +-
arch/x86/kernel/apic/apic_noop.c | 2 +-
arch/x86/kernel/apic/msi.c | 8 ++------
arch/x86/kernel/apic/probe_32.c | 2 +-
arch/x86/kernel/apic/x2apic_cluster.c | 2 +-
drivers/pci/host/pci-hyperv.c | 8 ++------
6 files changed, 8 insertions(+), 16 deletions(-)
diff --git a/arch/x86/kernel/apic/apic_flat_64.c b/arch/x86/kernel/apic/apic_flat_64.c
index aa85690..25a8702 100644
--- a/arch/x86/kernel/apic/apic_flat_64.c
+++ b/arch/x86/kernel/apic/apic_flat_64.c
@@ -151,7 +151,7 @@ static struct apic apic_flat __ro_after_init = {
.apic_id_valid = default_apic_id_valid,
.apic_id_registered = flat_apic_id_registered,
- .irq_delivery_mode = dest_LowestPrio,
+ .irq_delivery_mode = dest_Fixed,
.irq_dest_mode = 1, /* logical */
.disable_esr = 0,
diff --git a/arch/x86/kernel/apic/apic_noop.c b/arch/x86/kernel/apic/apic_noop.c
index 7b659c4..5078b5c 100644
--- a/arch/x86/kernel/apic/apic_noop.c
+++ b/arch/x86/kernel/apic/apic_noop.c
@@ -110,7 +110,7 @@ struct apic apic_noop __ro_after_init = {
.apic_id_valid = default_apic_id_valid,
.apic_id_registered = noop_apic_id_registered,
- .irq_delivery_mode = dest_LowestPrio,
+ .irq_delivery_mode = dest_Fixed,
/* logical delivery broadcast to all CPUs: */
.irq_dest_mode = 1,
diff --git a/arch/x86/kernel/apic/msi.c b/arch/x86/kernel/apic/msi.c
index 9b18be7..ce503c9 100644
--- a/arch/x86/kernel/apic/msi.c
+++ b/arch/x86/kernel/apic/msi.c
@@ -39,17 +39,13 @@ static void irq_msi_compose_msg(struct irq_data *data, struct msi_msg *msg)
((apic->irq_dest_mode == 0) ?
MSI_ADDR_DEST_MODE_PHYSICAL :
MSI_ADDR_DEST_MODE_LOGICAL) |
- ((apic->irq_delivery_mode != dest_LowestPrio) ?
- MSI_ADDR_REDIRECTION_CPU :
- MSI_ADDR_REDIRECTION_LOWPRI) |
+ MSI_ADDR_REDIRECTION_CPU |
MSI_ADDR_DEST_ID(cfg->dest_apicid);
msg->data =
MSI_DATA_TRIGGER_EDGE |
MSI_DATA_LEVEL_ASSERT |
- ((apic->irq_delivery_mode != dest_LowestPrio) ?
- MSI_DATA_DELIVERY_FIXED :
- MSI_DATA_DELIVERY_LOWPRI) |
+ MSI_DATA_DELIVERY_FIXED |
MSI_DATA_VECTOR(cfg->vector);
}
diff --git a/arch/x86/kernel/apic/probe_32.c b/arch/x86/kernel/apic/probe_32.c
index fa22017..02e8acb 100644
--- a/arch/x86/kernel/apic/probe_32.c
+++ b/arch/x86/kernel/apic/probe_32.c
@@ -105,7 +105,7 @@ static struct apic apic_default __ro_after_init = {
.apic_id_valid = default_apic_id_valid,
.apic_id_registered = default_apic_id_registered,
- .irq_delivery_mode = dest_LowestPrio,
+ .irq_delivery_mode = dest_Fixed,
/* logical delivery broadcast to all CPUs: */
.irq_dest_mode = 1,
diff --git a/arch/x86/kernel/apic/x2apic_cluster.c b/arch/x86/kernel/apic/x2apic_cluster.c
index 622f13c..8b04234 100644
--- a/arch/x86/kernel/apic/x2apic_cluster.c
+++ b/arch/x86/kernel/apic/x2apic_cluster.c
@@ -184,7 +184,7 @@ static struct apic apic_x2apic_cluster __ro_after_init = {
.apic_id_valid = x2apic_apic_id_valid,
.apic_id_registered = x2apic_apic_id_registered,
- .irq_delivery_mode = dest_LowestPrio,
+ .irq_delivery_mode = dest_Fixed,
.irq_dest_mode = 1, /* logical */
.disable_esr = 0,
diff --git a/drivers/pci/host/pci-hyperv.c b/drivers/pci/host/pci-hyperv.c
index 0fe3ea1..e7d9447 100644
--- a/drivers/pci/host/pci-hyperv.c
+++ b/drivers/pci/host/pci-hyperv.c
@@ -985,9 +985,7 @@ static u32 hv_compose_msi_req_v1(
int_pkt->wslot.slot = slot;
int_pkt->int_desc.vector = vector;
int_pkt->int_desc.vector_count = 1;
- int_pkt->int_desc.delivery_mode =
- (apic->irq_delivery_mode == dest_LowestPrio) ?
- dest_LowestPrio : dest_Fixed;
+ int_pkt->int_desc.delivery_mode = dest_Fixed;
/*
* Create MSI w/ dummy vCPU set, overwritten by subsequent retarget in
@@ -1008,9 +1006,7 @@ static u32 hv_compose_msi_req_v2(
int_pkt->wslot.slot = slot;
int_pkt->int_desc.vector = vector;
int_pkt->int_desc.vector_count = 1;
- int_pkt->int_desc.delivery_mode =
- (apic->irq_delivery_mode == dest_LowestPrio) ?
- dest_LowestPrio : dest_Fixed;
+ int_pkt->int_desc.delivery_mode = dest_Fixed;
/*
* Create MSI w/ dummy vCPU set targeting just one vCPU, overwritten
next prev parent reply other threads:[~2017-12-29 13:33 UTC|newest]
Thread overview: 31+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-11-15 10:05 thinkpad x60: sound problems in 4.14.0-next-20171114 Pavel Machek
2017-11-15 10:43 ` Takashi Iwai
2017-11-15 11:11 ` Pavel Machek
2017-11-15 11:14 ` Takashi Iwai
2017-11-20 23:25 ` Pavel Machek
2017-11-27 16:30 ` thinkpad x60: sound problems in 4.15-rc1 was " Pavel Machek
2017-11-27 16:33 ` Takashi Iwai
2017-11-27 18:31 ` Pavel Machek
2017-11-27 18:35 ` Takashi Iwai
2017-11-27 18:44 ` Pavel Machek
2017-11-28 7:00 ` Takashi Iwai
2017-12-14 9:57 ` Pavel Machek
2017-12-19 2:06 ` vcaputo
2017-12-19 4:54 ` vcaputo
2017-12-19 23:12 ` vcaputo
2017-12-19 23:22 ` Pavel Machek
2017-12-20 0:36 ` vcaputo
2017-12-20 0:33 ` Thomas Gleixner
2017-12-20 0:59 ` vcaputo
2017-12-23 5:37 ` vcaputo
2017-12-23 20:37 ` vcaputo
2017-12-23 20:33 ` Thomas Gleixner
2017-12-24 16:16 ` vcaputo
2017-12-28 10:41 ` Thomas Gleixner
2017-12-28 18:30 ` vcaputo
2017-12-28 23:24 ` [tip:x86/urgent] x86/apic: Switch all APICs to Fixed delivery mode tip-bot for Thomas Gleixner
2017-12-29 13:31 ` tip-bot for Thomas Gleixner [this message]
2017-12-29 13:35 ` Thomas Gleixner
2017-12-25 10:12 ` thinkpad x60: sound problems in 4.15-rc1 was Re: thinkpad x60: sound problems in 4.14.0-next-20171114 Pavel Machek
2017-12-25 10:09 ` Pavel Machek
2018-01-02 20:54 ` Pavel Machek
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=tip-a31e58e129f73ab5b04016330b13ed51fde7a961@git.kernel.org \
--to=tipbot@zytor.com \
--cc=hpa@zytor.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-tip-commits@vger.kernel.org \
--cc=mingo@kernel.org \
--cc=pavel@ucw.cz \
--cc=tglx@linutronix.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
Powered by JetHome