* [PATCH 2/2] arm64: dts: amlogic: add support for Radxa ZERO 2 Pro
2024-07-11 20:16 [PATCH 1/2] dt-bindings: arm: amlogic: add support for Radxa ZERO 2 Pro FUKAUMI Naoki
@ 2024-07-11 20:16 ` FUKAUMI Naoki
0 siblings, 0 replies; 2+ messages in thread
From: FUKAUMI Naoki @ 2024-07-11 20:16 UTC (permalink / raw)
To: neil.armstrong
Cc: robh, krzk+dt, conor+dt, khilman, jbrunet, martin.blumenstingl,
devicetree, linux-amlogic, FUKAUMI Naoki
Radxa ZERO 2 Pro is a ultra tiny high performance SBC[1] using the
Amlogic A311D chip that ships in a number of eMMC configurations:
- Amlogic A311D SoC
- Quad A73 + Dual A53 CPU
- Mali G52-MP4 GPU
- NPU (5 TOPs)
- 4GB LPDDR4 RAM
- 32/64/128GB eMMC
- micro SD Card slot
- Wi-Fi 5 and BT 5.0
- 1x USB 2.0 Type-C port (OTG)
- 1x USB 3.0 Type-C port (Host)
- Micro HDMI 2.0
- MIPI DSI
- MIPI CSI
- 40 Pin GPIO header
[1] https://radxa.com/products/zeros/zero2pro
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
---
arch/arm64/boot/dts/amlogic/Makefile | 1 +
.../amlogic/meson-g12b-radxa-zero-2pro.dts | 14 +
.../dts/amlogic/meson-g12b-radxa-zero2.dts | 527 +-----------------
...-zero2.dts => meson-g12b-radxa-zero2.dtsi} | 4 -
4 files changed, 29 insertions(+), 517 deletions(-)
create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-radxa-zero-2pro.dts
rewrite arch/arm64/boot/dts/amlogic/meson-g12b-radxa-zero2.dts (98%)
copy arch/arm64/boot/dts/amlogic/{meson-g12b-radxa-zero2.dts => meson-g12b-radxa-zero2.dtsi} (98%)
diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index 29417f04f886..4f95721698d0 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -31,6 +31,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-go-ultra.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2-plus.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2l.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-g12b-radxa-zero-2pro.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-radxa-zero2.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-s922x-bananapi-m2s.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-s922x-khadas-vim3.dtb
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-radxa-zero-2pro.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-radxa-zero-2pro.dts
new file mode 100644
index 000000000000..62e44de9a550
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b-radxa-zero-2pro.dts
@@ -0,0 +1,14 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include "meson-g12b-radxa-zero2.dtsi"
+
+/ {
+ compatible = "radxa,zero-2pro", "amlogic,a311d", "amlogic,g12b";
+ model = "Radxa ZERO 2 Pro";
+};
+
+&sound {
+ model = "RADXA-ZERO-2PRO";
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-radxa-zero2.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-radxa-zero2.dts
dissimilarity index 98%
index 8445701100d0..b4734cb63aaa 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12b-radxa-zero2.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b-radxa-zero2.dts
@@ -1,513 +1,14 @@
-// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
-/*
- * Copyright (c) 2019 BayLibre, SAS
- * Author: Neil Armstrong <narmstrong@baylibre.com>
- * Copyright (c) 2019 Christian Hewitt <christianshewitt@gmail.com>
- * Copyright (c) 2022 Radxa Limited
- * Author: Yuntian Zhang <yt@radxa.com>
- */
-
-/dts-v1/;
-
-#include "meson-g12b-a311d.dtsi"
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/leds/common.h>
-#include <dt-bindings/gpio/meson-g12a-gpio.h>
-#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
-
-/ {
- compatible = "radxa,zero2", "amlogic,a311d", "amlogic,g12b";
- model = "Radxa Zero2";
-
- aliases {
- serial0 = &uart_AO;
- serial2 = &uart_A;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-
- memory@0 {
- device_type = "memory";
- reg = <0x0 0x0 0x0 0x80000000>;
- };
-
- fan0: pwm-fan {
- compatible = "pwm-fan";
- #cooling-cells = <2>;
- cooling-levels = <0 64 128 192 255>;
- pwms = <&pwm_AO_ab 0 40000 0>;
- };
-
- gpio-keys-polled {
- compatible = "gpio-keys-polled";
- poll-interval = <100>;
- power-button {
- label = "power";
- linux,code = <KEY_POWER>;
- gpios = <&gpio_ao GPIOAO_3 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
- };
- };
-
- leds {
- compatible = "gpio-leds";
-
- led-green {
- color = <LED_COLOR_ID_GREEN>;
- function = LED_FUNCTION_STATUS;
- gpios = <&gpio GPIOA_12 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "heartbeat";
- };
- };
-
- hdmi-connector {
- compatible = "hdmi-connector";
- type = "a";
-
- port {
- hdmi_connector_in: endpoint {
- remote-endpoint = <&hdmi_tx_tmds_out>;
- };
- };
- };
-
- emmc_pwrseq: emmc-pwrseq {
- compatible = "mmc-pwrseq-emmc";
- reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
- };
-
- sdio_pwrseq: sdio-pwrseq {
- compatible = "mmc-pwrseq-simple";
- reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
- clocks = <&wifi32k>;
- clock-names = "ext_clock";
- };
-
- ao_5v: regulator-ao-5v {
- compatible = "regulator-fixed";
- regulator-name = "AO_5V";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- regulator-always-on;
- };
-
- vcc_1v8: regulator-vcc-1v8 {
- compatible = "regulator-fixed";
- regulator-name = "VCC_1V8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- vin-supply = <&vcc_3v3>;
- regulator-always-on;
- };
-
- vcc_3v3: regulator-vcc-3v3 {
- compatible = "regulator-fixed";
- regulator-name = "VCC_3V3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- vin-supply = <&vddao_3v3>;
- regulator-always-on;
- /* FIXME: actually controlled by VDDCPU_B_EN */
- };
-
- vddao_1v8: regulator-vddao-1v8 {
- compatible = "regulator-fixed";
- regulator-name = "VDDIO_AO1V8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- vin-supply = <&vddao_3v3>;
- regulator-always-on;
- };
-
- vddao_3v3: regulator-vddao-3v3 {
- compatible = "regulator-fixed";
- regulator-name = "VDDAO_3V3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- vin-supply = <&ao_5v>;
- regulator-always-on;
- };
-
- vddcpu_a: regulator-vddcpu-a {
- /*
- * MP8756GD Regulator.
- */
- compatible = "pwm-regulator";
-
- regulator-name = "VDDCPU_A";
- regulator-min-microvolt = <730000>;
- regulator-max-microvolt = <1022000>;
-
- pwm-supply = <&ao_5v>;
-
- pwms = <&pwm_ab 0 1250 0>;
- pwm-dutycycle-range = <100 0>;
-
- regulator-boot-on;
- regulator-always-on;
- };
-
- vddcpu_b: regulator-vddcpu-b {
- /*
- * Silergy SY8120B1ABC Regulator.
- */
- compatible = "pwm-regulator";
-
- regulator-name = "VDDCPU_B";
- regulator-min-microvolt = <730000>;
- regulator-max-microvolt = <1022000>;
-
- pwm-supply = <&ao_5v>;
-
- pwms = <&pwm_AO_cd 1 1250 0>;
- pwm-dutycycle-range = <100 0>;
-
- regulator-boot-on;
- regulator-always-on;
- };
-
- sound {
- compatible = "amlogic,axg-sound-card";
- model = "RADXA-ZERO2";
- audio-aux-devs = <&tdmout_b>;
- audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
- "TDMOUT_B IN 1", "FRDDR_B OUT 1",
- "TDMOUT_B IN 2", "FRDDR_C OUT 1",
- "TDM_B Playback", "TDMOUT_B OUT";
-
- assigned-clocks = <&clkc CLKID_MPLL2>,
- <&clkc CLKID_MPLL0>,
- <&clkc CLKID_MPLL1>;
- assigned-clock-parents = <0>, <0>, <0>;
- assigned-clock-rates = <294912000>,
- <270950400>,
- <393216000>;
-
- dai-link-0 {
- sound-dai = <&frddr_a>;
- };
-
- dai-link-1 {
- sound-dai = <&frddr_b>;
- };
-
- dai-link-2 {
- sound-dai = <&frddr_c>;
- };
-
- /* 8ch hdmi interface */
- dai-link-3 {
- sound-dai = <&tdmif_b>;
- dai-format = "i2s";
- dai-tdm-slot-tx-mask-0 = <1 1>;
- dai-tdm-slot-tx-mask-1 = <1 1>;
- dai-tdm-slot-tx-mask-2 = <1 1>;
- dai-tdm-slot-tx-mask-3 = <1 1>;
- mclk-fs = <256>;
-
- codec {
- sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>;
- };
- };
-
- /* hdmi glue */
- dai-link-4 {
- sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>;
-
- codec {
- sound-dai = <&hdmi_tx>;
- };
- };
- };
-
- wifi32k: clock-0 {
- compatible = "pwm-clock";
- #clock-cells = <0>;
- clock-frequency = <32768>;
- pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
- };
-};
-
-&arb {
- status = "okay";
-};
-
-&cec_AO {
- pinctrl-0 = <&cec_ao_a_h_pins>;
- pinctrl-names = "default";
- status = "disabled";
- hdmi-phandle = <&hdmi_tx>;
-};
-
-&cecb_AO {
- pinctrl-0 = <&cec_ao_b_h_pins>;
- pinctrl-names = "default";
- status = "okay";
- hdmi-phandle = <&hdmi_tx>;
-};
-
-&clkc_audio {
- status = "okay";
-};
-
-&cpu0 {
- cpu-supply = <&vddcpu_b>;
- operating-points-v2 = <&cpu_opp_table_0>;
- clocks = <&clkc CLKID_CPU_CLK>;
- clock-latency = <50000>;
-};
-
-&cpu1 {
- cpu-supply = <&vddcpu_b>;
- operating-points-v2 = <&cpu_opp_table_0>;
- clocks = <&clkc CLKID_CPU_CLK>;
- clock-latency = <50000>;
-};
-
-&cpu100 {
- cpu-supply = <&vddcpu_a>;
- operating-points-v2 = <&cpub_opp_table_1>;
- clocks = <&clkc CLKID_CPUB_CLK>;
- clock-latency = <50000>;
-};
-
-&cpu101 {
- cpu-supply = <&vddcpu_a>;
- operating-points-v2 = <&cpub_opp_table_1>;
- clocks = <&clkc CLKID_CPUB_CLK>;
- clock-latency = <50000>;
-};
-
-&cpu102 {
- cpu-supply = <&vddcpu_a>;
- operating-points-v2 = <&cpub_opp_table_1>;
- clocks = <&clkc CLKID_CPUB_CLK>;
- clock-latency = <50000>;
-};
-
-&cpu103 {
- cpu-supply = <&vddcpu_a>;
- operating-points-v2 = <&cpub_opp_table_1>;
- clocks = <&clkc CLKID_CPUB_CLK>;
- clock-latency = <50000>;
-};
-
-&cpu_thermal {
- trips {
- cpu_active: cpu-active {
- temperature = <70000>; /* millicelsius */
- hysteresis = <2000>; /* millicelsius */
- type = "active";
- };
- };
-
- cooling-maps {
- map2 {
- trip = <&cpu_active>;
- cooling-device = <&fan0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
- };
- };
-};
-
-&frddr_a {
- status = "okay";
-};
-
-&frddr_b {
- status = "okay";
-};
-
-&frddr_c {
- status = "okay";
-};
-
-&gpio {
- gpio-line-names =
- /* GPIOZ */
- "PIN_27", "PIN_28", "PIN_7", "PIN_11", "PIN_13", "PIN_15", "PIN_18", "PIN_40",
- "", "", "", "", "", "", "", "",
- /* GPIOH */
- "", "", "", "", "PIN_19", "PIN_21", "PIN_24", "PIN_23",
- "",
- /* BOOT */
- "", "", "", "", "", "", "", "",
- "", "", "", "", "EMMC_PWRSEQ", "", "", "",
- /* GPIOC */
- "", "", "", "", "", "", "SD_CD", "PIN_36",
- /* GPIOA */
- "PIN_32", "PIN_12", "PIN_35", "", "", "PIN_38", "", "",
- "", "", "", "", "LED_GREEN", "PIN_31", "PIN_3", "PIN_5",
- /* GPIOX */
- "", "", "", "", "", "", "SDIO_PWRSEQ", "",
- "", "", "", "", "", "", "", "",
- "", "BT_SHUTDOWN", "", "";
-};
-
-&gpio_ao {
- gpio-line-names =
- /* GPIOAO */
- "PIN_8", "PIN_10", "", "BTN_POWER", "", "", "", "PIN_29",
- "PIN_33", "PIN_37", "FAN", "",
- /* GPIOE */
- "", "", "";
-};
-
-&hdmi_tx {
- status = "okay";
- pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
- pinctrl-names = "default";
- hdmi-supply = <&ao_5v>;
-};
-
-&hdmi_tx_tmds_port {
- hdmi_tx_tmds_out: endpoint {
- remote-endpoint = <&hdmi_connector_in>;
- };
-};
-
-&ir {
- status = "disabled";
- pinctrl-0 = <&remote_input_ao_pins>;
- pinctrl-names = "default";
-};
-
-&pwm_ab {
- pinctrl-0 = <&pwm_a_e_pins>;
- pinctrl-names = "default";
- clocks = <&xtal>;
- clock-names = "clkin0";
- status = "okay";
-};
-
-&pwm_ef {
- pinctrl-0 = <&pwm_e_pins>;
- pinctrl-names = "default";
- clocks = <&xtal>;
- clock-names = "clkin0";
- status = "okay";
-};
-
-&pwm_AO_ab {
- pinctrl-0 = <&pwm_ao_a_pins>;
- pinctrl-names = "default";
- clocks = <&xtal>;
- clock-names = "clkin0";
- status = "okay";
-};
-
-&pwm_AO_cd {
- pinctrl-0 = <&pwm_ao_d_e_pins>;
- pinctrl-names = "default";
- clocks = <&xtal>;
- clock-names = "clkin1";
- status = "okay";
-};
-
-&saradc {
- status = "okay";
- vref-supply = <&vddao_1v8>;
-};
-
-/* SDIO */
-&sd_emmc_a {
- status = "okay";
- pinctrl-0 = <&sdio_pins>;
- pinctrl-1 = <&sdio_clk_gate_pins>;
- pinctrl-names = "default", "clk-gate";
- #address-cells = <1>;
- #size-cells = <0>;
-
- bus-width = <4>;
- cap-sd-highspeed;
- max-frequency = <100000000>;
-
- non-removable;
- disable-wp;
-
- /* WiFi firmware requires power to be kept while in suspend */
- keep-power-in-suspend;
-
- mmc-pwrseq = <&sdio_pwrseq>;
-
- vmmc-supply = <&vddao_3v3>;
- vqmmc-supply = <&vddao_1v8>;
-
- brcmf: wifi@1 {
- reg = <1>;
- compatible = "brcm,bcm4329-fmac";
- };
-};
-
-/* SD card */
-&sd_emmc_b {
- status = "okay";
- pinctrl-0 = <&sdcard_c_pins>;
- pinctrl-1 = <&sdcard_clk_gate_c_pins>;
- pinctrl-names = "default", "clk-gate";
-
- bus-width = <4>;
- cap-sd-highspeed;
- max-frequency = <50000000>;
- disable-wp;
-
- cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
- vmmc-supply = <&vddao_3v3>;
- vqmmc-supply = <&vddao_3v3>;
-};
-
-/* eMMC */
-&sd_emmc_c {
- status = "okay";
- pinctrl-0 = <&emmc_ctrl_pins>, <&emmc_data_8b_pins>, <&emmc_ds_pins>;
- pinctrl-1 = <&emmc_clk_gate_pins>;
- pinctrl-names = "default", "clk-gate";
-
- bus-width = <8>;
- cap-mmc-highspeed;
- mmc-ddr-1_8v;
- mmc-hs200-1_8v;
- max-frequency = <200000000>;
- disable-wp;
-
- mmc-pwrseq = <&emmc_pwrseq>;
- vmmc-supply = <&vcc_3v3>;
- vqmmc-supply = <&vcc_1v8>;
-};
-
-&tdmif_b {
- status = "okay";
-};
-
-&tdmout_b {
- status = "okay";
-};
-
-&tohdmitx {
- status = "okay";
-};
-
-&uart_A {
- status = "okay";
- pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
- pinctrl-names = "default";
- uart-has-rtscts;
-
- bluetooth {
- compatible = "brcm,bcm43438-bt";
- shutdown-gpios = <&gpio GPIOX_17 GPIO_ACTIVE_HIGH>;
- max-speed = <2000000>;
- clocks = <&wifi32k>;
- clock-names = "lpo";
- };
-};
-
-&uart_AO {
- status = "okay";
- pinctrl-0 = <&uart_ao_a_pins>;
- pinctrl-names = "default";
-};
-
-&usb {
- status = "okay";
-};
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include "meson-g12b-radxa-zero2.dtsi"
+
+/ {
+ compatible = "radxa,zero2", "amlogic,a311d", "amlogic,g12b";
+ model = "Radxa ZERO2";
+};
+
+&sound {
+ model = "RADXA-ZERO2";
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-radxa-zero2.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-radxa-zero2.dtsi
similarity index 98%
copy from arch/arm64/boot/dts/amlogic/meson-g12b-radxa-zero2.dts
copy to arch/arm64/boot/dts/amlogic/meson-g12b-radxa-zero2.dtsi
index 8445701100d0..3c30505d1440 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12b-radxa-zero2.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b-radxa-zero2.dtsi
@@ -16,9 +16,6 @@
#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
/ {
- compatible = "radxa,zero2", "amlogic,a311d", "amlogic,g12b";
- model = "Radxa Zero2";
-
aliases {
serial0 = &uart_AO;
serial2 = &uart_A;
@@ -169,7 +166,6 @@ vddcpu_b: regulator-vddcpu-b {
sound {
compatible = "amlogic,axg-sound-card";
- model = "RADXA-ZERO2";
audio-aux-devs = <&tdmout_b>;
audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
"TDMOUT_B IN 1", "FRDDR_B OUT 1",
--
2.43.0
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
^ permalink raw reply [flat|nested] 2+ messages in thread