mirror of https://lore.kernel.org/linux-amlogic/
 help / color / mirror / Atom feed
From: narmstrong@baylibre.com (Neil Armstrong)
To: linus-amlogic@lists.infradead.org
Subject: [PATCH] ARM64: dts: meson-axg: add ethernet mac controller
Date: Fri, 17 Nov 2017 14:12:57 +0100	[thread overview]
Message-ID: <4d6ef632-a28f-6598-befb-85ad17480f04@baylibre.com> (raw)
In-Reply-To: <20171113080155.2463-1-yixun.lan@amlogic.com>

On 13/11/2017 09:01, Yixun Lan wrote:
> Add DT info for the stmmac ethernet MAC which found in
> the Amlogic's Meson-AXG SoC, also describe the ethernet
> pinctrl & clock information here.
> 
> This is tested in the S400 dev board which use a RTL8211F PHY,
> and the pins connect to the 'eth_rgmii_y_pins' group.
> 
> Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
> ---
>  arch/arm64/boot/dts/amlogic/meson-axg-s400.dts |  7 ++++
>  arch/arm64/boot/dts/amlogic/meson-axg.dtsi     | 53 ++++++++++++++++++++++++++
>  2 files changed, 60 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/amlogic/meson-axg-s400.dts b/arch/arm64/boot/dts/amlogic/meson-axg-s400.dts
> index 9eb6aaee155d..7b39a9fe2b0f 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-axg-s400.dts
> +++ b/arch/arm64/boot/dts/amlogic/meson-axg-s400.dts
> @@ -21,3 +21,10 @@
>  	status = "okay";
>  };
>  
> +&ethmac {
> +	status = "okay";
> +	phy-mode = "rgmii";
> +
> +	pinctrl-0 = <&eth_rgmii_y_pins>;
> +	pinctrl-names = "default";
> +};
> diff --git a/arch/arm64/boot/dts/amlogic/meson-axg.dtsi b/arch/arm64/boot/dts/amlogic/meson-axg.dtsi
> index 65945c6c8b65..57faaa9d8013 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-axg.dtsi
> +++ b/arch/arm64/boot/dts/amlogic/meson-axg.dtsi
> @@ -157,6 +157,19 @@
>  			#address-cells = <0>;
>  		};
>  
> +		ethmac: ethernet at ff3f0000 {
> +			compatible = "amlogic,meson-axg-dwmac", "amlogic,meson-gxbb-dwmac", "snps,dwmac";
> +			reg = <0x0 0xff3f0000 0x0 0x10000
> +				0x0 0xff634540 0x0 0x8>;
> +			interrupts = <GIC_SPI 8 IRQ_TYPE_EDGE_RISING>;
> +			interrupt-names = "macirq";
> +			status = "disabled";
> +			clocks = <&clkc CLKID_ETH>,
> +				 <&clkc CLKID_FCLK_DIV2>,
> +				 <&clkc CLKID_MPLL2>;
> +			clock-names = "stmmaceth", "clkin0", "clkin1";
> +		};
> +
>  		hiubus: hiubus at ff63c000 {
>  			compatible = "simple-bus";
>  			reg = <0x0 0xff63c000 0x0 0x1c00>;
> @@ -203,6 +216,46 @@
>  					#gpio-cells = <2>;
>  					gpio-ranges = <&pinctrl_periphs 0 0 86>;
>  				};
> +
> +				eth_rgmii_x_pins: eth-x-rgmii {
> +					mux {
> +						groups = "eth_mdio_x",
> +						       "eth_mdc_x",
> +						       "eth_rgmii_rx_clk_x",
> +						       "eth_rx_dv_x",
> +						       "eth_rxd0_x",
> +						       "eth_rxd1_x",
> +						       "eth_rxd2_rgmii",
> +						       "eth_rxd3_rgmii",
> +						       "eth_rgmii_tx_clk",
> +						       "eth_txen_x",
> +						       "eth_txd0_x",
> +						       "eth_txd1_x",
> +						       "eth_txd2_rgmii",
> +						       "eth_txd3_rgmii";
> +						function = "eth";
> +					};
> +				};
> +
> +				eth_rgmii_y_pins: eth-y-rgmii {
> +					mux {
> +						groups = "eth_mdio_y",
> +						       "eth_mdc_y",
> +						       "eth_rgmii_rx_clk_y",
> +						       "eth_rx_dv_y",
> +						       "eth_rxd0_y",
> +						       "eth_rxd1_y",
> +						       "eth_rxd2_rgmii",
> +						       "eth_rxd3_rgmii",
> +						       "eth_rgmii_tx_clk",
> +						       "eth_txen_y",
> +						       "eth_txd0_y",
> +						       "eth_txd1_y",
> +						       "eth_txd2_rgmii",
> +						       "eth_txd3_rgmii";
> +						function = "eth";
> +					};
> +				};
>  			};
>  		};
>  
> 

Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>

  reply	other threads:[~2017-11-17 13:12 UTC|newest]

Thread overview: 3+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2017-11-13  8:01 Yixun Lan
2017-11-17 13:12 ` Neil Armstrong [this message]
2017-12-06 20:07 ` Kevin Hilman

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=4d6ef632-a28f-6598-befb-85ad17480f04@baylibre.com \
    --to=narmstrong@baylibre.com \
    --cc=linus-amlogic@lists.infradead.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®