* [PATCH 0/3] Add and enable USB nodes for ExynosAutov920 SoC [not found] <CGME20251024114018epcas5p4e09ca8ea47ff2295a08a162864a47284@epcas5p4.samsung.com> @ 2025-10-24 11:48 ` Pritam Manohar Sutar [not found] ` <CGME20251024114026epcas5p33c612c143853daccf21dd9515418df58@epcas5p3.samsung.com> ` (3 more replies) 0 siblings, 4 replies; 7+ messages in thread From: Pritam Manohar Sutar @ 2025-10-24 11:48 UTC (permalink / raw) To: robh, krzk+dt, conor+dt, alim.akhtar Cc: devicetree, linux-arm-kernel, linux-samsung-soc, linux-kernel, rosa.pila, dev.tailor, faraz.ata, muhammed.ali, selvarasu.g, pritam.sutar This SoC has 2 USB typeC and 2 typeA ports those are DWC3 DRD controllers and amoung them, one is USB3.1 DRD combo phy and three USB2.0 phy controllers. This patchset adds and enables USB and USB-PHY nodes in dts. PMIC driver is not implmented yet, we rely on USB LDOs being enabled by the bootloader and used dummy regulators for now. To drive vbus for host mode, it needs GPIO pin to enable vbus regulator. GPIO expander is present in the dts, we used it to enable the vbus regulator using GPIO. USB ports are configured as OTG, and default mode is configured as peripheral. These configurations might be changed based on requirements. This patchset has dependancy on schema and driver implementation[1] and role switch control from userspace[2] patches. [1]: https://lore.kernel.org/linux-phy/20251010070912.3758334-1-pritam.sutar@samsung.com/ [2]: https://lore.kernel.org/linux-usb/20251024085455.789555-1-pritam.sutar@samsung.com/ Pritam Manohar Sutar (3): arm64: dts: exynos: ExynosAutov920: Add USB and USB-phy nodes arm64: dts: exynos: ExynosAutov920: Add regulators for the USB arm64: dts: exynos: ExynosAutov920: Enable USB nodes .../boot/dts/exynos/exynosautov920-sadk.dts | 160 +++++++++++++++++ .../arm64/boot/dts/exynos/exynosautov920.dtsi | 162 ++++++++++++++++++ 2 files changed, 322 insertions(+) -- 2.34.1 ^ permalink raw reply [flat|nested] 7+ messages in thread
[parent not found: <CGME20251024114026epcas5p33c612c143853daccf21dd9515418df58@epcas5p3.samsung.com>]
* [PATCH 1/3] arm64: dts: exynos: ExynosAutov920: Add USB and USB-phy nodes [not found] ` <CGME20251024114026epcas5p33c612c143853daccf21dd9515418df58@epcas5p3.samsung.com> @ 2025-10-24 11:48 ` Pritam Manohar Sutar 0 siblings, 0 replies; 7+ messages in thread From: Pritam Manohar Sutar @ 2025-10-24 11:48 UTC (permalink / raw) To: robh, krzk+dt, conor+dt, alim.akhtar Cc: devicetree, linux-arm-kernel, linux-samsung-soc, linux-kernel, rosa.pila, dev.tailor, faraz.ata, muhammed.ali, selvarasu.g, pritam.sutar Add USB and USB PHY controller nodes. Signed-off-by: Pritam Manohar Sutar <pritam.sutar@samsung.com> --- .../arm64/boot/dts/exynos/exynosautov920.dtsi | 162 ++++++++++++++++++ 1 file changed, 162 insertions(+) diff --git a/arch/arm64/boot/dts/exynos/exynosautov920.dtsi b/arch/arm64/boot/dts/exynos/exynosautov920.dtsi index 6ee74d260776..6ff0e00fd901 100644 --- a/arch/arm64/boot/dts/exynos/exynosautov920.dtsi +++ b/arch/arm64/boot/dts/exynos/exynosautov920.dtsi @@ -1409,6 +1409,168 @@ pinctrl_hsi1: pinctrl@16450000 { interrupts = <GIC_SPI 456 IRQ_TYPE_LEVEL_HIGH>; }; + usbdrd31_ssphy: phy@16480000 { + compatible = "samsung,exynosautov920-usb31drd-combo-ssphy"; + reg = <0x16480000 0x0200>; + clocks = <&cmu_hsi1 CLK_MOUT_HSI1_NOC_USER>, + <&cmu_hsi1 CLK_MOUT_HSI1_USBDRD>; + clock-names = "phy", "ref"; + #phy-cells = <1>; + samsung,pmu-syscon = <&pmu_system_controller>; + status = "disabled"; + }; + + usbdrd31_hsphy: phy@16490000 { + compatible = "samsung,exynosautov920-usbdrd-combo-hsphy"; + reg = <0x16490000 0x0200>; + clocks = <&cmu_hsi1 CLK_MOUT_HSI1_NOC_USER>, + <&cmu_hsi1 CLK_MOUT_HSI1_USBDRD>; + clock-names = "phy", "ref"; + #phy-cells = <1>; + samsung,pmu-syscon = <&pmu_system_controller>; + status = "disabled"; + }; + + usbdrd20_phy0: phy@16500000 { + compatible = "samsung,exynosautov920-usbdrd-phy"; + reg = <0x16500000 0x0200>; + clocks = <&cmu_hsi1 CLK_MOUT_HSI1_NOC_USER>, + <&cmu_hsi1 CLK_MOUT_HSI1_USBDRD>; + clock-names = "phy", "ref"; + #phy-cells = <1>; + samsung,pmu-syscon = <&pmu_system_controller>; + status = "disabled"; + }; + + usbdrd20_phy1: phy@16510000 { + compatible = "samsung,exynosautov920-usbdrd-phy"; + reg = <0x16510000 0x0200>; + clocks = <&cmu_hsi1 CLK_MOUT_HSI1_NOC_USER>, + <&cmu_hsi1 CLK_MOUT_HSI1_USBDRD>; + clock-names = "phy", "ref"; + #phy-cells = <1>; + samsung,pmu-syscon = <&pmu_system_controller>; + status = "disabled"; + }; + + usbdrd20_phy2: phy@16520000 { + compatible = "samsung,exynosautov920-usbdrd-phy"; + reg = <0x16520000 0x0200>; + clocks = <&cmu_hsi1 CLK_MOUT_HSI1_NOC_USER>, + <&cmu_hsi1 CLK_MOUT_HSI1_USBDRD>; + clock-names = "phy", "ref"; + #phy-cells = <1>; + samsung,pmu-syscon = <&pmu_system_controller>; + status = "disabled"; + }; + + /* This usb port supports usb31 and usb20 speeds */ + usbdrd31: usb@16600000 { + compatible = "samsung,exynosautov920-dwusb3"; + ranges = <0x0 0x16600000 0x10000>; + clocks = <&cmu_hsi1 CLK_MOUT_HSI1_USBDRD>, + <&cmu_hsi1 CLK_MOUT_HSI1_USBDRD>; + clock-names = "ref", "susp_clk"; + #address-cells = <1>; + #size-cells = <1>; + status = "disabled"; + + usbdrd31_dwc3: usb@0 { + compatible = "snps,dwc3"; + reg = <0x0 0x10000>; + clocks = <&cmu_hsi1 CLK_MOUT_HSI1_USBDRD>, + <&cmu_hsi1 CLK_MOUT_HSI1_USBDRD>; + clock-names = "ref", "susp_clk"; + interrupts = <GIC_SPI 491 IRQ_TYPE_LEVEL_HIGH>; + phys = <&usbdrd31_hsphy 0>, <&usbdrd31_ssphy 0>; + phy-names = "usb2-phy", "usb3-phy"; + snps,has-lpm-erratum; + snps,dis_u2_susphy_quirk; + snps,dis_u3_susphy_quirk; + }; + }; + + /* This usb port supports only usb20 speeds */ + usbdrd20_0: usb@16700000 { + compatible = "samsung,exynosautov920-dwusb3"; + ranges = <0x0 0x16700000 0x10000>; + clocks = <&cmu_hsi1 CLK_MOUT_HSI1_USBDRD>, + <&cmu_hsi1 CLK_MOUT_HSI1_USBDRD>; + clock-names = "ref", "susp_clk"; + #address-cells = <1>; + #size-cells = <1>; + status = "disabled"; + + usbdrd20_dwc3_0: usb@0 { + compatible = "snps,dwc3"; + reg = <0x0 0x10000>; + clocks = <&cmu_hsi1 CLK_MOUT_HSI1_USBDRD>, + <&cmu_hsi1 CLK_MOUT_HSI1_USBDRD>; + clock-names = "ref", "susp_clk"; + interrupts = <GIC_SPI 479 IRQ_TYPE_LEVEL_HIGH>; + phys = <&usbdrd20_phy0 0>; + phy-names = "usb2-phy"; + snps,has-lpm-erratum; + snps,dis_u2_susphy_quirk; + snps,dis_u3_susphy_quirk; + snps,quirk-frame-length-adjustment = <0x20>; + }; + }; + + /* This usb port supports only usb20 speeds */ + usbdrd20_1: usb@16800000 { + compatible = "samsung,exynosautov920-dwusb3"; + ranges = <0x0 0x16800000 0x10000>; + clocks = <&cmu_hsi1 CLK_MOUT_HSI1_USBDRD>, + <&cmu_hsi1 CLK_MOUT_HSI1_USBDRD>; + clock-names = "ref", "susp_clk"; + #address-cells = <1>; + #size-cells = <1>; + status = "disabled"; + + usbdrd20_dwc3_1: usb@0 { + compatible = "snps,dwc3"; + reg = <0x0 0x10000>; + clocks = <&cmu_hsi1 CLK_MOUT_HSI1_USBDRD>, + <&cmu_hsi1 CLK_MOUT_HSI1_USBDRD>; + clock-names = "ref", "susp_clk"; + interrupts = <GIC_SPI 481 IRQ_TYPE_LEVEL_HIGH>; + phys = <&usbdrd20_phy1 0>; + phy-names = "usb2-phy"; + snps,has-lpm-erratum; + snps,dis_u2_susphy_quirk; + snps,dis_u3_susphy_quirk; + snps,quirk-frame-length-adjustment = <0x20>; + }; + }; + + /* This usb port supports only usb20 speeds */ + usbdrd20_2: usb@16900000 { + compatible = "samsung,exynosautov920-dwusb3"; + ranges = <0x0 0x16900000 0x10000>; + clocks = <&cmu_hsi1 CLK_MOUT_HSI1_USBDRD>, + <&cmu_hsi1 CLK_MOUT_HSI1_USBDRD>; + clock-names = "ref", "susp_clk"; + #address-cells = <1>; + #size-cells = <1>; + status = "disabled"; + + usbdrd20_dwc3_2: usb@0 { + compatible = "snps,dwc3"; + reg = <0x0 0x10000>; + clocks = <&cmu_hsi1 CLK_MOUT_HSI1_USBDRD>, + <&cmu_hsi1 CLK_MOUT_HSI1_USBDRD>; + clock-names = "ref", "susp_clk"; + interrupts = <GIC_SPI 483 IRQ_TYPE_LEVEL_HIGH>; + phys = <&usbdrd20_phy2 0>; + phy-names = "usb2-phy"; + snps,has-lpm-erratum; + snps,dis_u2_susphy_quirk; + snps,dis_u3_susphy_quirk; + snps,quirk-frame-length-adjustment = <0x20>; + }; + }; + cmu_hsi2: clock-controller@16b00000 { compatible = "samsung,exynosautov920-cmu-hsi2"; reg = <0x16b00000 0x8000>; -- 2.34.1 ^ permalink raw reply [flat|nested] 7+ messages in thread
[parent not found: <CGME20251024114030epcas5p2c9ba90eaa354440873b73263746fa148@epcas5p2.samsung.com>]
* [PATCH 2/3] arm64: dts: exynos: ExynosAutov920: Add regulators for the USB [not found] ` <CGME20251024114030epcas5p2c9ba90eaa354440873b73263746fa148@epcas5p2.samsung.com> @ 2025-10-24 11:48 ` Pritam Manohar Sutar 0 siblings, 0 replies; 7+ messages in thread From: Pritam Manohar Sutar @ 2025-10-24 11:48 UTC (permalink / raw) To: robh, krzk+dt, conor+dt, alim.akhtar Cc: devicetree, linux-arm-kernel, linux-samsung-soc, linux-kernel, rosa.pila, dev.tailor, faraz.ata, muhammed.ali, selvarasu.g, pritam.sutar Add dummy regulator for USB and PHY supplies. Add vbus regulator that is enabled by GPIO pin. Signed-off-by: Pritam Manohar Sutar <pritam.sutar@samsung.com> --- .../boot/dts/exynos/exynosautov920-sadk.dts | 139 ++++++++++++++++++ 1 file changed, 139 insertions(+) diff --git a/arch/arm64/boot/dts/exynos/exynosautov920-sadk.dts b/arch/arm64/boot/dts/exynos/exynosautov920-sadk.dts index a397f068ed53..f90f7704597c 100644 --- a/arch/arm64/boot/dts/exynos/exynosautov920-sadk.dts +++ b/arch/arm64/boot/dts/exynos/exynosautov920-sadk.dts @@ -52,6 +52,76 @@ memory@80000000 { <0x8 0x80000000 0x1 0xfba00000>, <0xa 0x00000000 0x2 0x00000000>; }; + + /* TODO: Remove this once PMIC is implemented */ + dummy_regulator: regulator-0 { + compatible = "regulator-fixed"; + regulator-name = "dummy_regulator"; + }; + + usbdrd31_dwc3_vbus: usbdrd31_dwc3-vbus { + compatible = "regulator-fixed"; + regulator-name = "usbdrd31_dwc3-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + gpio = <&gpp2 0 GPIO_ACTIVE_HIGH>; + }; + + /* Use gpio for enabling vbus regulator */ + usb_phy0: usb-phy0 { + compatible = "usb-nop-xceiv"; + vbus-supply = <&usbdrd31_dwc3_vbus>; + }; + + usbdrd20_dwc3_0_vbus: usbdrd20_dwc3_0-vbus { + compatible = "regulator-fixed"; + regulator-name = "usbdrd20_dwc3_0-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + gpio = <&gpp2 1 GPIO_ACTIVE_HIGH>; + }; + + /* Use gpio for enabling vbus regulator */ + usb_phy1: usb-phy1 { + compatible = "usb-nop-xceiv"; + vbus-supply = <&usbdrd20_dwc3_0_vbus>; + }; + + usbdrd20_dwc3_1_vbus: usbdrd20_dwc3_1-vbus { + compatible = "regulator-fixed"; + regulator-name = "usbdrd20_dwc3_1-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + gpio = <&gpp2 2 GPIO_ACTIVE_HIGH>; + }; + + /* Use gpio for enabling vbus regulator */ + usb_phy2: usb-phy2 { + compatible = "usb-nop-xceiv"; + vbus-supply = <&usbdrd20_dwc3_1_vbus>; + }; + + usbdrd20_dwc3_2_vbus: usbdrd20_dwc3_2-vbus { + compatible = "regulator-fixed"; + regulator-name = "usbdrd20_dwc3_2-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + gpio = <&gpp2 3 GPIO_ACTIVE_HIGH>; + }; + + /* Use gpio for enabling vbus regulator */ + usb_phy3: usb-phy3 { + compatible = "usb-nop-xceiv"; + vbus-supply = <&usbdrd20_dwc3_2_vbus>; + }; }; &pinctrl_alive { @@ -86,3 +156,72 @@ &usi_0 { &xtcxo { clock-frequency = <38400000>; }; + +&usbdrd31_ssphy { + dvdd-supply = <&dummy_regulator>; + vdd18-supply = <&dummy_regulator>; +}; + +&usbdrd31_hsphy { + dvdd-supply = <&dummy_regulator>; + vdd18-supply = <&dummy_regulator>; + vdd33-supply = <&dummy_regulator>; +}; + +&usbdrd31_dwc3 { + maximum-speed = "super-speed-plus"; + usb-phy = <&usb_phy0>; +}; + +&usbdrd31 { + vdd10-supply = <&dummy_regulator>; + vdd33-supply = <&dummy_regulator>; +}; + +&usbdrd20_phy0 { + dvdd-supply = <&dummy_regulator>; + vdd18-supply = <&dummy_regulator>; + vdd33-supply = <&dummy_regulator>; +}; + +&usbdrd20_dwc3_0 { + maximum-speed = "high-speed"; + usb-phy = <&usb_phy1>; +}; + +&usbdrd20_0 { + vdd10-supply = <&dummy_regulator>; + vdd33-supply = <&dummy_regulator>; +}; + +&usbdrd20_phy1 { + dvdd-supply = <&dummy_regulator>; + vdd18-supply = <&dummy_regulator>; + vdd33-supply = <&dummy_regulator>; +}; + +&usbdrd20_dwc3_1 { + maximum-speed = "high-speed"; + usb-phy = <&usb_phy2>; +}; + +&usbdrd20_1 { + vdd10-supply = <&dummy_regulator>; + vdd33-supply = <&dummy_regulator>; +}; + +&usbdrd20_phy2 { + dvdd-supply = <&dummy_regulator>; + vdd18-supply = <&dummy_regulator>; + vdd33-supply = <&dummy_regulator>; +}; + +&usbdrd20_dwc3_2 { + maximum-speed = "high-speed"; + usb-phy = <&usb_phy3>; +}; + +&usbdrd20_2 { + vdd10-supply = <&dummy_regulator>; + vdd33-supply = <&dummy_regulator>; +}; -- 2.34.1 ^ permalink raw reply [flat|nested] 7+ messages in thread
[parent not found: <CGME20251024114040epcas5p3d8c093798a3fd6c9c3b0c89aa58be8ce@epcas5p3.samsung.com>]
* [PATCH 3/3] arm64: dts: exynos: ExynosAutov920: Enable USB nodes [not found] ` <CGME20251024114040epcas5p3d8c093798a3fd6c9c3b0c89aa58be8ce@epcas5p3.samsung.com> @ 2025-10-24 11:48 ` Pritam Manohar Sutar 0 siblings, 0 replies; 7+ messages in thread From: Pritam Manohar Sutar @ 2025-10-24 11:48 UTC (permalink / raw) To: robh, krzk+dt, conor+dt, alim.akhtar Cc: devicetree, linux-arm-kernel, linux-samsung-soc, linux-kernel, rosa.pila, dev.tailor, faraz.ata, muhammed.ali, selvarasu.g, pritam.sutar Enable USB PHY and DWC3 USB controllers' nodes. Signed-off-by: Pritam Manohar Sutar <pritam.sutar@samsung.com> --- .../boot/dts/exynos/exynosautov920-sadk.dts | 21 +++++++++++++++++++ 1 file changed, 21 insertions(+) diff --git a/arch/arm64/boot/dts/exynos/exynosautov920-sadk.dts b/arch/arm64/boot/dts/exynos/exynosautov920-sadk.dts index f90f7704597c..5896dd69334a 100644 --- a/arch/arm64/boot/dts/exynos/exynosautov920-sadk.dts +++ b/arch/arm64/boot/dts/exynos/exynosautov920-sadk.dts @@ -160,15 +160,20 @@ &xtcxo { &usbdrd31_ssphy { dvdd-supply = <&dummy_regulator>; vdd18-supply = <&dummy_regulator>; + status = "okay"; }; &usbdrd31_hsphy { dvdd-supply = <&dummy_regulator>; vdd18-supply = <&dummy_regulator>; vdd33-supply = <&dummy_regulator>; + status = "okay"; }; &usbdrd31_dwc3 { + dr_mode = "otg"; + usb-role-switch; + role-switch-default-mode = "peripheral"; maximum-speed = "super-speed-plus"; usb-phy = <&usb_phy0>; }; @@ -176,15 +181,20 @@ &usbdrd31_dwc3 { &usbdrd31 { vdd10-supply = <&dummy_regulator>; vdd33-supply = <&dummy_regulator>; + status = "okay"; }; &usbdrd20_phy0 { dvdd-supply = <&dummy_regulator>; vdd18-supply = <&dummy_regulator>; vdd33-supply = <&dummy_regulator>; + status = "okay"; }; &usbdrd20_dwc3_0 { + dr_mode = "otg"; + usb-role-switch; + role-switch-default-mode = "peripheral"; maximum-speed = "high-speed"; usb-phy = <&usb_phy1>; }; @@ -192,15 +202,20 @@ &usbdrd20_dwc3_0 { &usbdrd20_0 { vdd10-supply = <&dummy_regulator>; vdd33-supply = <&dummy_regulator>; + status = "okay"; }; &usbdrd20_phy1 { dvdd-supply = <&dummy_regulator>; vdd18-supply = <&dummy_regulator>; vdd33-supply = <&dummy_regulator>; + status = "okay"; }; &usbdrd20_dwc3_1 { + dr_mode = "otg"; + usb-role-switch; + role-switch-default-mode = "peripheral"; maximum-speed = "high-speed"; usb-phy = <&usb_phy2>; }; @@ -208,15 +223,20 @@ &usbdrd20_dwc3_1 { &usbdrd20_1 { vdd10-supply = <&dummy_regulator>; vdd33-supply = <&dummy_regulator>; + status = "okay"; }; &usbdrd20_phy2 { dvdd-supply = <&dummy_regulator>; vdd18-supply = <&dummy_regulator>; vdd33-supply = <&dummy_regulator>; + status = "okay"; }; &usbdrd20_dwc3_2 { + dr_mode = "otg"; + usb-role-switch; + role-switch-default-mode = "peripheral"; maximum-speed = "high-speed"; usb-phy = <&usb_phy3>; }; @@ -224,4 +244,5 @@ &usbdrd20_dwc3_2 { &usbdrd20_2 { vdd10-supply = <&dummy_regulator>; vdd33-supply = <&dummy_regulator>; + status = "okay"; }; -- 2.34.1 ^ permalink raw reply [flat|nested] 7+ messages in thread
* RE: [PATCH 0/3] Add and enable USB nodes for ExynosAutov920 SoC 2025-10-24 11:48 ` [PATCH 0/3] Add and enable USB nodes for ExynosAutov920 SoC Pritam Manohar Sutar ` (2 preceding siblings ...) [not found] ` <CGME20251024114040epcas5p3d8c093798a3fd6c9c3b0c89aa58be8ce@epcas5p3.samsung.com> @ 2026-01-22 10:31 ` Pritam Manohar Sutar 2026-01-22 10:40 ` Krzysztof Kozlowski 3 siblings, 1 reply; 7+ messages in thread From: Pritam Manohar Sutar @ 2026-01-22 10:31 UTC (permalink / raw) To: robh, krzk+dt, conor+dt, alim.akhtar Cc: devicetree, linux-arm-kernel, linux-samsung-soc, linux-kernel, rosa.pila, dev.tailor, faraz.ata, muhammed.ali, selvarasu.g Hi All, > -----Original Message----- > From: Pritam Manohar Sutar <pritam.sutar@samsung.com> > Sent: 24 October 2025 05:19 PM > To: robh@kernel.org; krzk+dt@kernel.org; conor+dt@kernel.org; > alim.akhtar@samsung.com > Cc: devicetree@vger.kernel.org; linux-arm-kernel@lists.infradead.org; linux- > samsung-soc@vger.kernel.org; linux-kernel@vger.kernel.org; > rosa.pila@samsung.com; dev.tailor@samsung.com; faraz.ata@samsung.com; > muhammed.ali@samsung.com; selvarasu.g@samsung.com; > pritam.sutar@samsung.com > Subject: [PATCH 0/3] Add and enable USB nodes for ExynosAutov920 SoC > > This SoC has 2 USB typeC and 2 typeA ports those are DWC3 DRD controllers and > amoung them, one is USB3.1 DRD combo phy and three > USB2.0 phy controllers. This patchset adds and enables USB and USB-PHY nodes > in dts. > > PMIC driver is not implmented yet, we rely on USB LDOs being enabled by the > bootloader and used dummy regulators for now. > > To drive vbus for host mode, it needs GPIO pin to enable vbus regulator. > GPIO expander is present in the dts, we used it to enable the vbus regulator > using GPIO. > > USB ports are configured as OTG, and default mode is configured as peripheral. > These configurations might be changed based on requirements. > > This patchset has dependancy on schema and driver implementation[1] and role > switch control from userspace[2] patches. > [1]: https://lore.kernel.org/linux-phy/20251010070912.3758334-1- > pritam.sutar@samsung.com/ > [2]: https://lore.kernel.org/linux-usb/20251024085455.789555-1- > pritam.sutar@samsung.com/ Above dependent patches are merged, can you please review the patchset? > > Pritam Manohar Sutar (3): > arm64: dts: exynos: ExynosAutov920: Add USB and USB-phy nodes > arm64: dts: exynos: ExynosAutov920: Add regulators for the USB > arm64: dts: exynos: ExynosAutov920: Enable USB nodes > > .../boot/dts/exynos/exynosautov920-sadk.dts | 160 +++++++++++++++++ > .../arm64/boot/dts/exynos/exynosautov920.dtsi | 162 ++++++++++++++++++ > 2 files changed, 322 insertions(+) > > -- > 2.34.1 Thank you, Regards, Pritam ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH 0/3] Add and enable USB nodes for ExynosAutov920 SoC 2026-01-22 10:31 ` [PATCH 0/3] Add and enable USB nodes for ExynosAutov920 SoC Pritam Manohar Sutar @ 2026-01-22 10:40 ` Krzysztof Kozlowski 2026-01-22 12:57 ` Pritam Manohar Sutar 0 siblings, 1 reply; 7+ messages in thread From: Krzysztof Kozlowski @ 2026-01-22 10:40 UTC (permalink / raw) To: Pritam Manohar Sutar, robh, krzk+dt, conor+dt, alim.akhtar Cc: devicetree, linux-arm-kernel, linux-samsung-soc, linux-kernel, rosa.pila, dev.tailor, faraz.ata, muhammed.ali, selvarasu.g On 22/01/2026 11:31, Pritam Manohar Sutar wrote: > Hi All, > >> -----Original Message----- >> From: Pritam Manohar Sutar <pritam.sutar@samsung.com> >> Sent: 24 October 2025 05:19 PM >> To: robh@kernel.org; krzk+dt@kernel.org; conor+dt@kernel.org; >> alim.akhtar@samsung.com >> Cc: devicetree@vger.kernel.org; linux-arm-kernel@lists.infradead.org; linux- >> samsung-soc@vger.kernel.org; linux-kernel@vger.kernel.org; >> rosa.pila@samsung.com; dev.tailor@samsung.com; faraz.ata@samsung.com; >> muhammed.ali@samsung.com; selvarasu.g@samsung.com; >> pritam.sutar@samsung.com >> Subject: [PATCH 0/3] Add and enable USB nodes for ExynosAutov920 SoC >> >> This SoC has 2 USB typeC and 2 typeA ports those are DWC3 DRD controllers and >> amoung them, one is USB3.1 DRD combo phy and three >> USB2.0 phy controllers. This patchset adds and enables USB and USB-PHY nodes >> in dts. >> >> PMIC driver is not implmented yet, we rely on USB LDOs being enabled by the >> bootloader and used dummy regulators for now. >> >> To drive vbus for host mode, it needs GPIO pin to enable vbus regulator. >> GPIO expander is present in the dts, we used it to enable the vbus regulator >> using GPIO. >> >> USB ports are configured as OTG, and default mode is configured as peripheral. >> These configurations might be changed based on requirements. >> >> This patchset has dependancy on schema and driver implementation[1] and role >> switch control from userspace[2] patches. >> [1]: https://lore.kernel.org/linux-phy/20251010070912.3758334-1- >> pritam.sutar@samsung.com/ >> [2]: https://lore.kernel.org/linux-usb/20251024085455.789555-1- >> pritam.sutar@samsung.com/ This wasn't even a dependency... > > Above dependent patches are merged, can you please review the patchset? I closed my tree few days ago, so next cycle, but please resend, because this is three months old now. I dropped it from my queue long time ago. Best regards, Krzysztof ^ permalink raw reply [flat|nested] 7+ messages in thread
* RE: [PATCH 0/3] Add and enable USB nodes for ExynosAutov920 SoC 2026-01-22 10:40 ` Krzysztof Kozlowski @ 2026-01-22 12:57 ` Pritam Manohar Sutar 0 siblings, 0 replies; 7+ messages in thread From: Pritam Manohar Sutar @ 2026-01-22 12:57 UTC (permalink / raw) To: 'Krzysztof Kozlowski', robh, krzk+dt, conor+dt, alim.akhtar Cc: devicetree, linux-arm-kernel, linux-samsung-soc, linux-kernel, rosa.pila, dev.tailor, faraz.ata, muhammed.ali, selvarasu.g Hi Krzysztof, > -----Original Message----- > From: Krzysztof Kozlowski <krzk@kernel.org> > Sent: 22 January 2026 04:10 PM > To: Pritam Manohar Sutar <pritam.sutar@samsung.com>; robh@kernel.org; > krzk+dt@kernel.org; conor+dt@kernel.org; alim.akhtar@samsung.com > Cc: devicetree@vger.kernel.org; linux-arm-kernel@lists.infradead.org; linux- > samsung-soc@vger.kernel.org; linux-kernel@vger.kernel.org; > rosa.pila@samsung.com; dev.tailor@samsung.com; faraz.ata@samsung.com; > muhammed.ali@samsung.com; selvarasu.g@samsung.com > Subject: Re: [PATCH 0/3] Add and enable USB nodes for ExynosAutov920 SoC > > On 22/01/2026 11:31, Pritam Manohar Sutar wrote: > > Hi All, > > > >> -----Original Message----- > >> From: Pritam Manohar Sutar <pritam.sutar@samsung.com> > >> Sent: 24 October 2025 05:19 PM > >> To: robh@kernel.org; krzk+dt@kernel.org; conor+dt@kernel.org; > >> alim.akhtar@samsung.com > >> Cc: devicetree@vger.kernel.org; linux-arm-kernel@lists.infradead.org; > >> linux- samsung-soc@vger.kernel.org; linux-kernel@vger.kernel.org; > >> rosa.pila@samsung.com; dev.tailor@samsung.com; > faraz.ata@samsung.com; > >> muhammed.ali@samsung.com; selvarasu.g@samsung.com; > >> pritam.sutar@samsung.com > >> Subject: [PATCH 0/3] Add and enable USB nodes for ExynosAutov920 SoC > >> > >> This SoC has 2 USB typeC and 2 typeA ports those are DWC3 DRD > >> controllers and amoung them, one is USB3.1 DRD combo phy and three > >> USB2.0 phy controllers. This patchset adds and enables USB and > >> USB-PHY nodes in dts. > >> > >> PMIC driver is not implmented yet, we rely on USB LDOs being enabled > >> by the bootloader and used dummy regulators for now. > >> > >> To drive vbus for host mode, it needs GPIO pin to enable vbus regulator. > >> GPIO expander is present in the dts, we used it to enable the vbus > >> regulator using GPIO. > >> > >> USB ports are configured as OTG, and default mode is configured as > peripheral. > >> These configurations might be changed based on requirements. > >> > >> This patchset has dependancy on schema and driver implementation[1] > >> and role switch control from userspace[2] patches. > >> [1]: https://lore.kernel.org/linux-phy/20251010070912.3758334-1- > >> pritam.sutar@samsung.com/ > >> [2]: https://lore.kernel.org/linux-usb/20251024085455.789555-1- > >> pritam.sutar@samsung.com/ > > This wasn't even a dependency... > > > > > Above dependent patches are merged, can you please review the patchset? > > I closed my tree few days ago, so next cycle, but please resend, because this is > three months old now. I dropped it from my queue long time ago. Noted and resent same patch series as v2 patchset. Link for v2: https://lore.kernel.org/linux-devicetree/20260122130721.205664-1-pritam.sutar@samsung.com/ > > Best regards, > Krzysztof Thank you. Regards, Pritam ^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2026-01-22 12:57 UTC | newest]
Thread overview: 7+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
[not found] <CGME20251024114018epcas5p4e09ca8ea47ff2295a08a162864a47284@epcas5p4.samsung.com>
2025-10-24 11:48 ` [PATCH 0/3] Add and enable USB nodes for ExynosAutov920 SoC Pritam Manohar Sutar
[not found] ` <CGME20251024114026epcas5p33c612c143853daccf21dd9515418df58@epcas5p3.samsung.com>
2025-10-24 11:48 ` [PATCH 1/3] arm64: dts: exynos: ExynosAutov920: Add USB and USB-phy nodes Pritam Manohar Sutar
[not found] ` <CGME20251024114030epcas5p2c9ba90eaa354440873b73263746fa148@epcas5p2.samsung.com>
2025-10-24 11:48 ` [PATCH 2/3] arm64: dts: exynos: ExynosAutov920: Add regulators for the USB Pritam Manohar Sutar
[not found] ` <CGME20251024114040epcas5p3d8c093798a3fd6c9c3b0c89aa58be8ce@epcas5p3.samsung.com>
2025-10-24 11:48 ` [PATCH 3/3] arm64: dts: exynos: ExynosAutov920: Enable USB nodes Pritam Manohar Sutar
2026-01-22 10:31 ` [PATCH 0/3] Add and enable USB nodes for ExynosAutov920 SoC Pritam Manohar Sutar
2026-01-22 10:40 ` Krzysztof Kozlowski
2026-01-22 12:57 ` Pritam Manohar Sutar
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®