Re: [PATCH 2/2] arch: arm64: dts: Add support for AM69 Starter Kit

[Vignesh Raghavendra <vigneshr@ti.com>]

Hi Sabiya

On 25/01/23 6:44 pm, Dasnavis Sabiya wrote:
> Hi Krzysztof,
> 
> On Mon, Jan 23, 2023 at 12:58 PM Dasnavis Sabiya
> <sabiya.d@mistralsolutions.com> wrote:
>> Hi Krzysztof,
>>
>> On Fri, Jan 20, 2023 at 4:03 PM Vignesh Raghavendra <vigneshr@ti.com> wrote:
>>> Hi Krzysztof,
>>>
>>> On 19/01/23 19:06, Krzysztof Kozlowski wrote:
>>>> On 19/01/2023 14:29, sabiya.d@mistralsolutions.com wrote:
>>>>> From: Dasnavis Sabiya <sabiya.d@ti.com>
>>>>>
>>>>> AM69 Starter Kit is a single board designed for TI AM69 SOC that
>>>>> provides advanced system integration in automotive ADAS applications,
>>>>> autonomous mobile robot and edge AI applications. The SOC comprises
>>>>> of Cortex-A72s in dual clusters, lockstep capable dual Cortex-R5F MCUs,
>>>>> Vision Processing Accelerators (VPAC) with Image Signal Processor (ISP)
>>>>> and multiple vision assist accelerators, Depth and Motion Processing
>>>>> Accelerators (DMPAC), Deep-learning Matrix Multiply Accelerator(MMA)
>>>>> and C7x floating point vector DSP
>>>>>
>>>>> AM69 SK supports the following interfaces:
>>>>>        * 32 GB LPDDR4 RAM
>>>>>        * x1 Gigabit Ethernet interface
>>>>>        * x3 USB 3.0 Type-A ports
>>>>>        * x1 USB 3.0 Type-C port
>>>>>        * x1 UHS-1 capable micro-SD card slot
>>>>>        * x4 MCAN instances
>>>>>        * 32 GB eMMC Flash
>>>>>        * 512 Mbit OSPI flash
>>>>>        * x2 Display connectors
>>>>>        * x1 PCIe M.2 M Key
>>>>>        * x1 PCIe M.2 E Key
>>>>>        * x1 4L PCIe Card Slot
>>>>>        * x3 CSI2 Camera interface
>>>>>        * 40-pin Raspberry Pi header
>>>>>
>>>>> Add initial support for the AM69 SK board.
>>>> Thank you for your patch. There is something to discuss/improve.
>>>>
>>>>> Design Files: https://www.ti.com/lit/zip/SPRR466
>>>>> TRM: https://www.ti.com/lit/zip/spruj52
>>>>>
>>>>> Signed-off-by: Dasnavis Sabiya <sabiya.d@ti.com>
>>>>> ---
>>>>>  arch/arm64/boot/dts/ti/Makefile       |   1 +
>>>>>  arch/arm64/boot/dts/ti/k3-am69-sk.dts | 180 ++++++++++++++++++++++++++
>>>>>  2 files changed, 181 insertions(+)
>>>>>  create mode 100644 arch/arm64/boot/dts/ti/k3-am69-sk.dts
>>>>>
>>>>> diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
>>>>> index e7c2c7dd0b25..04b1a7611096 100644
>>>>> --- a/arch/arm64/boot/dts/ti/Makefile
>>>>> +++ b/arch/arm64/boot/dts/ti/Makefile
>>>>> @@ -20,6 +20,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-j7200-common-proc-board.dtb
>>>>>
>>>>>  dtb-$(CONFIG_ARCH_K3) += k3-j721s2-common-proc-board.dtb
>>>>>
>>>>> +dtb-$(CONFIG_ARCH_K3) += k3-am69-sk.dtb
>>>> I was told the order of entries here is "time of release". Is it
>>>> correct? This is the order you want to keep here and am69-sk was
>>>> released after j721s2-common-proc-board but before j784s4-evm?
>>>
>>> Unfortunately, files are not in any particular order at the moment.
>>>
>>> Currently, entries are grouped into a block based upon SoC present on
>>> them. Boards within the family block are sorted alphabetically. But the
>>> block of SoCs itself is arranged in no particular order.
>>>
>>> I would like to propose to cleanup this file such that board dtbs are
>>> grouped as per SoC present on them (like now), sort the group
>>> alphabetically. Also then sort alphabetically within the family (similar
>>> how boards appear in dt bindings)
>>>
>>> Will do that towards end of rc6 once these patches are queued up to
>>> avoid merge conflicts.
>>>
>> As per the approach mentioned by Vignesh, I have grouped the am69 sk into
>> the SoC block J784S4 and sorted the board in alphabetical order.
>> Please revert with your thoughts on this.

> Could you please let me know if the approach is acceptable?

I intend to queue this series as is if there are no further comments and
then send a cleanup patch to reorder entries as I described above.

Regards
Vignesh