[PATCH v3 0/5] arm64: dts: qcom: kaanapali: Enable DisplayPort

[PATCH v3 0/5] arm64: dts: qcom: kaanapali: Enable DisplayPort

[Balaji Kalkonda]

This series adds DisplayPort support for the Qualcomm Kaanapali SoC
and enables it on the MTP board.

Kaanapali has a single DisplayPort controller based on the SM8750
generation DP block, routed through the combo USB/DP QMP PHY. The
series:

 - Documents the new "qcom,kaanapali-dp" compatible in the DP controller
   and Kaanapali MDSS bindings.
 - Adds the Kaanapali descriptor to the DP driver.
 - Describes the DisplayPort controller node in kaanapali.dtsi, including
   its OPP table, clocks, and power domain, and wires it to the DPU and
   the USB/DP QMP PHY.
 - Enables USB-C audio support on the MTP board (WCD939x USBSS Type-C mux)
   as a prerequisite for exercising DP alt mode over the same Type-C port.
 - Enables the DisplayPort controller on MTP and advertises the supported
   link frequencies for DisplayPort over USB-C.

Signed-off-by: Balaji Kalkonda <balaji.kalkonda@oss.qualcomm.com>
---
Changes in v3:
- Merged the Kaanapali DP resource-count constraints into the existing
  2-stream MST conditional block in the DP controller binding instead of
  duplicating it (Sashiko AI).
- Added the missing additionalProperties on the displayport-controller
  pattern property in the Kaanapali MDSS binding (Sashiko AI).
- Fixed the Kaanapali DP node register block sizes to match the actual
  register ranges (Konrad).
- Removed a stray blank line between the DP node clocks and clock-names
  properties (Konrad).
- Reordered the MTP DP node overrides to keep &mdss_dp0 and
  &mdss_dp0_out alphabetically sorted among the other node references
  (Konrad).
- Link to v2: https://patch.msgid.link/20261015-kaanapali_dp-v2-0-c15cb83d9140@oss.qualcomm.com

Changes in v2:
- Updated the DP controller binding patch subject from "Add Kaanapali" to
  "Document Kaanapali" and rewrote its commit message to describe the
  standalone compatible and SoC-specific resource counts (Sashiko AI).
- Updated the Kaanapali DP node to use the MMCX power domain (Dmitry,
  Sashiko AI).
- Added the missing second DP stream support in the Kaanapali DP node
  (Dmitry).
- Expanded the Kaanapali DP node commit message to document USB/DP PHY
  mode switching for DisplayPort altmode (Dmitry).
- Extended the MTP USB headset and Type-C commit message to document the
  WCD9395 USBSS mux I2C bus frequency of 100 kHz (Dmitry, Konrad,
  Mukesh).
- Removed an unnecessary line break from the DP node clock parent list
  (Dmitry).
- Link to v1: https://patch.msgid.link/20261005-kaanapali_dp-v1-0-6faeac3a6d59@oss.qualcomm.com

---
Balaji Kalkonda (5):
      dt-bindings: display/msm: dp-controller: Document Kaanapali
      drm/msm/dp: Add DisplayPort controller for Kaanapali
      arm64: dts: qcom: kaanapali: Add DisplayPort controller
      arm64: dts: qcom: kaanapali-mtp: Enable USB headset and Type-C accessory mode
      arm64: dts: qcom: kaanapali-mtp: Enable DisplayPort over USB

 .../bindings/display/msm/dp-controller.yaml        |  2 +
 .../bindings/display/msm/qcom,kaanapali-mdss.yaml  |  7 ++
 arch/arm64/boot/dts/qcom/kaanapali-mtp.dts         | 61 +++++++++++++++
 arch/arm64/boot/dts/qcom/kaanapali.dtsi            | 90 +++++++++++++++++++++-
 drivers/gpu/drm/msm/dp/dp_display.c                |  6 ++
 5 files changed, 164 insertions(+), 2 deletions(-)
---
base-commit: 9a482184d910775cf648863148944945b74e2815
change-id: 20261005-kaanapali_dp-f6d6839731fb

Best regards,
--  
Balaji Kalkonda <balaji.kalkonda@oss.qualcomm.com>

[PATCH v3 1/5] dt-bindings: display/msm: dp-controller: Document Kaanapali

[Balaji Kalkonda]

Document the DisplayPort controller on Qualcomm Kaanapali.

Kaanapali uses its own DP compatible string and has a resource
layout with five register ranges and six clocks. Add SoC-specific
constraints for those resource counts.

Signed-off-by: Balaji Kalkonda <balaji.kalkonda@oss.qualcomm.com>
---
 Documentation/devicetree/bindings/display/msm/dp-controller.yaml   | 2 ++
 .../devicetree/bindings/display/msm/qcom,kaanapali-mdss.yaml       | 7 +++++++
 2 files changed, 9 insertions(+)

diff --git a/Documentation/devicetree/bindings/display/msm/dp-controller.yaml b/Documentation/devicetree/bindings/display/msm/dp-controller.yaml
index 094a6383bb77..63e1b515a355 100644
--- a/Documentation/devicetree/bindings/display/msm/dp-controller.yaml
+++ b/Documentation/devicetree/bindings/display/msm/dp-controller.yaml
@@ -19,6 +19,7 @@ properties:
     oneOf:
       - enum:
           - qcom,glymur-dp
+          - qcom,kaanapali-dp
           - qcom,sa8775p-dp
           - qcom,sc7180-dp
           - qcom,sc7280-dp
@@ -275,6 +276,7 @@ allOf:
           contains:
             # 2 streams MST
             enum:
+              - qcom,kaanapali-dp
               - qcom,sc8180x-dp
               - qcom,sdm845-dp
               - qcom,sm8350-dp
diff --git a/Documentation/devicetree/bindings/display/msm/qcom,kaanapali-mdss.yaml b/Documentation/devicetree/bindings/display/msm/qcom,kaanapali-mdss.yaml
index 9f935defd6b1..b4851d1d48ea 100644
--- a/Documentation/devicetree/bindings/display/msm/qcom,kaanapali-mdss.yaml
+++ b/Documentation/devicetree/bindings/display/msm/qcom,kaanapali-mdss.yaml
@@ -48,6 +48,13 @@ patternProperties:
       compatible:
         const: qcom,kaanapali-dpu
 
+  "^displayport-controller@[0-9a-f]+$":
+    type: object
+    additionalProperties: true
+    properties:
+      compatible:
+        const: qcom,kaanapali-dp
+
   "^dsi@[0-9a-f]+$":
     type: object
     additionalProperties: true

-- 
2.34.1

[PATCH v3 2/5] drm/msm/dp: Add DisplayPort controller for Kaanapali

[Balaji Kalkonda]

The Qualcomm Kaanapali platform comes with a DisplayPort controller
with a different base offset than the previous SM8650 SoC, add support
for this in the DisplayPort driver.

Signed-off-by: Balaji Kalkonda <balaji.kalkonda@oss.qualcomm.com>
---
 drivers/gpu/drm/msm/dp/dp_display.c | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/drivers/gpu/drm/msm/dp/dp_display.c b/drivers/gpu/drm/msm/dp/dp_display.c
index 9299ce616fdb..348eb6967abf 100644
--- a/drivers/gpu/drm/msm/dp/dp_display.c
+++ b/drivers/gpu/drm/msm/dp/dp_display.c
@@ -158,6 +158,11 @@ static const struct msm_dp_desc msm_dp_desc_sm8650[] = {
 	{}
 };
 
+static const struct msm_dp_desc msm_dp_desc_kaanapali[] = {
+	{ .io_start = 0x09ad2000, .id = MSM_DP_CONTROLLER_0, .wide_bus_supported = true },
+	{}
+};
+
 static const struct msm_dp_desc msm_dp_desc_x1e80100[] = {
 	{ .io_start = 0x0ae90000, .id = MSM_DP_CONTROLLER_0, .wide_bus_supported = true },
 	{ .io_start = 0x0ae98000, .id = MSM_DP_CONTROLLER_1, .wide_bus_supported = true },
@@ -168,6 +173,7 @@ static const struct msm_dp_desc msm_dp_desc_x1e80100[] = {
 
 static const struct of_device_id msm_dp_dt_match[] = {
 	{ .compatible = "qcom,glymur-dp", .data = &msm_dp_desc_glymur },
+	{ .compatible = "qcom,kaanapali-dp", .data = &msm_dp_desc_kaanapali },
 	{ .compatible = "qcom,sa8775p-dp", .data = &msm_dp_desc_sa8775p },
 	{ .compatible = "qcom,sc7180-dp", .data = &msm_dp_desc_sc7180 },
 	{ .compatible = "qcom,sc7280-dp", .data = &msm_dp_desc_sc7280 },

-- 
2.34.1

[PATCH v3 3/5] arm64: dts: qcom: kaanapali: Add DisplayPort controller

[Balaji Kalkonda]

Add the DisplayPort controller node, including its OPP table,
controller clocks and power domain.

Connect the controller to the DPU and USB/DP QMP PHY, and enable
mode switching on the PHY for DisplayPort altmode.

Signed-off-by: Balaji Kalkonda <balaji.kalkonda@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/kaanapali.dtsi | 90 ++++++++++++++++++++++++++++++++-
 1 file changed, 88 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/kaanapali.dtsi b/arch/arm64/boot/dts/qcom/kaanapali.dtsi
index e48a179d0722..ee1fa830b6b1 100644
--- a/arch/arm64/boot/dts/qcom/kaanapali.dtsi
+++ b/arch/arm64/boot/dts/qcom/kaanapali.dtsi
@@ -3565,6 +3565,7 @@ usb_dp_qmpphy: phy@88e8000 {
 			#clock-cells = <1>;
 			#phy-cells = <1>;
 
+			mode-switch;
 			orientation-switch;
 
 			status = "disabled";
@@ -3592,6 +3593,7 @@ port@2 {
 					reg = <2>;
 
 					usb_dp_qmpphy_dp_in: endpoint {
+						remote-endpoint = <&mdss_dp0_out>;
 					};
 				};
 			};
@@ -3699,6 +3701,7 @@ port@2 {
 						reg = <2>;
 
 						dpu_intf0_out: endpoint {
+							remote-endpoint = <&mdss_dp0_in>;
 						};
 					};
 				};
@@ -3851,6 +3854,89 @@ mdss_dsi0_phy: phy@9ac1000 {
 
 				status = "disabled";
 			};
+
+			mdss_dp0: displayport-controller@9ad2000 {
+				compatible = "qcom,kaanapali-dp";
+				reg = <0x0 0x09ad2000 0x0 0x200>,
+				      <0x0 0x09ad2200 0x0 0x200>,
+				      <0x0 0x09ad3000 0x0 0xc00>,
+				      <0x0 0x09ad4000 0x0 0x400>,
+				      <0x0 0x09ad5000 0x0 0x400>;
+
+				interrupts-extended = <&mdss 12>;
+
+				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&dispcc DISP_CC_MDSS_DPTX0_AUX_CLK>,
+					 <&dispcc DISP_CC_MDSS_DPTX0_LINK_CLK>,
+					 <&dispcc DISP_CC_MDSS_DPTX0_LINK_INTF_CLK>,
+					 <&dispcc DISP_CC_MDSS_DPTX0_PIXEL0_CLK>,
+					 <&dispcc DISP_CC_MDSS_DPTX0_PIXEL1_CLK>;
+				clock-names = "core_iface",
+					      "core_aux",
+					      "ctrl_link",
+					      "ctrl_link_iface",
+					      "stream_pixel",
+					      "stream_1_pixel";
+
+				assigned-clocks = <&dispcc DISP_CC_MDSS_DPTX0_LINK_CLK_SRC>,
+						  <&dispcc DISP_CC_MDSS_DPTX0_PIXEL0_CLK_SRC>,
+						  <&dispcc DISP_CC_MDSS_DPTX0_PIXEL1_CLK_SRC>;
+				assigned-clock-parents = <&usb_dp_qmpphy QMP_USB43DP_DP_LINK_CLK>,
+							 <&usb_dp_qmpphy QMP_USB43DP_DP_VCO_DIV_CLK>,
+							 <&usb_dp_qmpphy QMP_USB43DP_DP_VCO_DIV_CLK>;
+
+				operating-points-v2 = <&dp_opp_table>;
+
+				power-domains = <&rpmhpd RPMHPD_MMCX>;
+
+				phys = <&usb_dp_qmpphy QMP_USB43DP_DP_PHY>;
+				phy-names = "dp";
+
+				#sound-dai-cells = <0>;
+
+				status = "disabled";
+
+				dp_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					opp-270000000 {
+						opp-hz = /bits/ 64 <270000000>;
+						required-opps = <&rpmhpd_opp_low_svs>;
+					};
+
+					opp-540000000 {
+						opp-hz = /bits/ 64 <540000000>;
+						required-opps = <&rpmhpd_opp_svs_l1>;
+					};
+
+					opp-810000000 {
+						opp-hz = /bits/ 64 <810000000>;
+						required-opps = <&rpmhpd_opp_nom>;
+					};
+				};
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						mdss_dp0_in: endpoint {
+							remote-endpoint = <&dpu_intf0_out>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+
+						mdss_dp0_out: endpoint {
+							data-lanes = <0 1 2 3>;
+							remote-endpoint = <&usb_dp_qmpphy_dp_in>;
+						};
+					};
+				};
+			};
 		};
 
 		dispcc: clock-controller@9ba2000 {
@@ -3860,8 +3946,8 @@ dispcc: clock-controller@9ba2000 {
 				 <&bi_tcxo_ao_div2>,
 				 <&gcc GCC_DISP_AHB_CLK>,
 				 <&sleep_clk>,
-				 <0>,
-				 <0>,
+				 <&usb_dp_qmpphy QMP_USB43DP_DP_LINK_CLK>,
+				 <&usb_dp_qmpphy QMP_USB43DP_DP_VCO_DIV_CLK>,
 				 <0>,
 				 <0>,
 				 <0>,

-- 
2.34.1

[PATCH v3 4/5] arm64: dts: qcom: kaanapali-mtp: Enable USB headset and Type-C accessory mode

[Balaji Kalkonda]

MTP does not have audio jack connected and relies on USB mux (WCD9395).
Add necessary nodes for proper audio headset support along with USB
Type-C accessory mode and orientation.

Set the I2C bus clock frequency to 100 kHz for the WCD9395 USBSS mux.

Signed-off-by: Balaji Kalkonda <balaji.kalkonda@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/kaanapali-mtp.dts | 53 ++++++++++++++++++++++++++++++
 1 file changed, 53 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/kaanapali-mtp.dts b/arch/arm64/boot/dts/qcom/kaanapali-mtp.dts
index 9eb02fd09dab..22eeacd7aecd 100644
--- a/arch/arm64/boot/dts/qcom/kaanapali-mtp.dts
+++ b/arch/arm64/boot/dts/qcom/kaanapali-mtp.dts
@@ -200,6 +200,7 @@ port@2 {
 					reg = <2>;
 
 					pmic_glink_sbu: endpoint {
+						remote-endpoint = <&wcd_usbss_sbu_mux>;
 					};
 				};
 			};
@@ -232,6 +233,15 @@ wcd939x: audio-codec {
 		vdd-px-supply = <&vreg_l1g_1p2>;
 
 		#sound-dai-cells = <1>;
+
+		mode-switch;
+		orientation-switch;
+
+		port {
+			wcd_codec_headset_in: endpoint {
+				remote-endpoint = <&wcd_usbss_headset_out>;
+			};
+		};
 	};
 
 	wcn7850-pmu {
@@ -916,6 +926,44 @@ &gpu_zap_shader {
 	firmware-name = "qcom/kaanapali/gen80200_zap.mbn";
 };
 
+&i2c3 {
+	clock-frequency = <100000>;
+
+	status = "okay";
+
+	wcd_usbss: typec-mux@e {
+		compatible = "qcom,wcd9395-usbss", "qcom,wcd9390-usbss";
+		reg = <0xe>;
+
+		vdd-supply = <&vreg_l15b_1p8>;
+		reset-gpios = <&tlmm 162 GPIO_ACTIVE_HIGH>;
+
+		mode-switch;
+		orientation-switch;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				wcd_usbss_sbu_mux: endpoint {
+					remote-endpoint = <&pmic_glink_sbu>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				wcd_usbss_headset_out: endpoint {
+					remote-endpoint = <&wcd_codec_headset_in>;
+				};
+			};
+		};
+	};
+};
+
 &lpass_vamacro {
 	pinctrl-0 = <&dmic01_default>, <&dmic23_default>;
 	pinctrl-names = "default";
@@ -1113,6 +1161,11 @@ &pon_resin {
 	status = "okay";
 };
 
+&qup_i2c3_data_clk {
+	/* Use internal I2C pull-up */
+	bias-pull-up = <2200>;
+};
+
 &remoteproc_adsp {
 	firmware-name = "qcom/kaanapali/adsp.mbn",
 			"qcom/kaanapali/adsp_dtb.mbn";

-- 
2.34.1

[PATCH v3 5/5] arm64: dts: qcom: kaanapali-mtp: Enable DisplayPort over USB

[Balaji Kalkonda]

Hook up DisplayPort parts over Type-C USB on MTP.

Signed-off-by: Balaji Kalkonda <balaji.kalkonda@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/kaanapali-mtp.dts | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/kaanapali-mtp.dts b/arch/arm64/boot/dts/qcom/kaanapali-mtp.dts
index 22eeacd7aecd..bcfd9e942eaa 100644
--- a/arch/arm64/boot/dts/qcom/kaanapali-mtp.dts
+++ b/arch/arm64/boot/dts/qcom/kaanapali-mtp.dts
@@ -976,6 +976,14 @@ &mdss {
 	status = "okay";
 };
 
+&mdss_dp0 {
+	status = "okay";
+};
+
+&mdss_dp0_out {
+	link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+};
+
 &mdss_dsi0 {
 	vdda-supply = <&vreg_l1d_1p2>;
 	status = "okay";

-- 
2.34.1

Re: [PATCH v3 2/5] drm/msm/dp: Add DisplayPort controller for Kaanapali

[Dmitry Baryshkov]

On Thu, Oct 22, 2026 at 03:19:43PM +0530, Balaji Kalkonda wrote:
> The Qualcomm Kaanapali platform comes with a DisplayPort controller
> with a different base offset than the previous SM8650 SoC, add support
> for this in the DisplayPort driver.
> 
> Signed-off-by: Balaji Kalkonda <balaji.kalkonda@oss.qualcomm.com>
> ---
>  drivers/gpu/drm/msm/dp/dp_display.c | 6 ++++++
>  1 file changed, 6 insertions(+)
> 

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>


-- 
With best wishes
Dmitry

Re: [PATCH v3 3/5] arm64: dts: qcom: kaanapali: Add DisplayPort controller

[Dmitry Baryshkov]

On Thu, Oct 22, 2026 at 03:19:44PM +0530, Balaji Kalkonda wrote:
> Add the DisplayPort controller node, including its OPP table,
> controller clocks and power domain.
> 
> Connect the controller to the DPU and USB/DP QMP PHY, and enable
> mode switching on the PHY for DisplayPort altmode.
> 
> Signed-off-by: Balaji Kalkonda <balaji.kalkonda@oss.qualcomm.com>
> ---
>  arch/arm64/boot/dts/qcom/kaanapali.dtsi | 90 ++++++++++++++++++++++++++++++++-
>  1 file changed, 88 insertions(+), 2 deletions(-)
> 

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>


-- 
With best wishes
Dmitry

Re: [PATCH v3 5/5] arm64: dts: qcom: kaanapali-mtp: Enable DisplayPort over USB

[Dmitry Baryshkov]

On Thu, Oct 22, 2026 at 03:19:46PM +0530, Balaji Kalkonda wrote:
> Hook up DisplayPort parts over Type-C USB on MTP.
> 
> Signed-off-by: Balaji Kalkonda <balaji.kalkonda@oss.qualcomm.com>
> ---
>  arch/arm64/boot/dts/qcom/kaanapali-mtp.dts | 8 ++++++++
>  1 file changed, 8 insertions(+)
> 

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>


-- 
With best wishes
Dmitry

Re: [PATCH v3 5/5] arm64: dts: qcom: kaanapali-mtp: Enable DisplayPort over USB

[Konrad Dybcio]

On 10/22/26 11:49 AM, Balaji Kalkonda wrote:
> Hook up DisplayPort parts over Type-C USB on MTP.
> 
> Signed-off-by: Balaji Kalkonda <balaji.kalkonda@oss.qualcomm.com>
> ---

Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>

Konrad

Re: [PATCH v3 4/5] arm64: dts: qcom: kaanapali-mtp: Enable USB headset and Type-C accessory mode

[Konrad Dybcio]

On 10/22/26 11:49 AM, Balaji Kalkonda wrote:
> MTP does not have audio jack connected and relies on USB mux (WCD9395).
> Add necessary nodes for proper audio headset support along with USB
> Type-C accessory mode and orientation.
> 
> Set the I2C bus clock frequency to 100 kHz for the WCD9395 USBSS mux.
> 
> Signed-off-by: Balaji Kalkonda <balaji.kalkonda@oss.qualcomm.com>
> ---

Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>

Konrad

Re: [PATCH v3 3/5] arm64: dts: qcom: kaanapali: Add DisplayPort controller

[Konrad Dybcio]

On 10/22/26 11:49 AM, Balaji Kalkonda wrote:
> Add the DisplayPort controller node, including its OPP table,
> controller clocks and power domain.
> 
> Connect the controller to the DPU and USB/DP QMP PHY, and enable
> mode switching on the PHY for DisplayPort altmode.
> 
> Signed-off-by: Balaji Kalkonda <balaji.kalkonda@oss.qualcomm.com>
> ---

Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>

Konrad

Re: [PATCH v3 2/5] drm/msm/dp: Add DisplayPort controller for Kaanapali

[Konrad Dybcio]

On 10/22/26 11:49 AM, Balaji Kalkonda wrote:
> The Qualcomm Kaanapali platform comes with a DisplayPort controller
> with a different base offset than the previous SM8650 SoC, add support
> for this in the DisplayPort driver.
> 
> Signed-off-by: Balaji Kalkonda <balaji.kalkonda@oss.qualcomm.com>
> ---

you lost the tags from v1

Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>

Konrad