From: Maxim Kochetkov <fido_max@inbox.ru>
To: Mark Brown <broonie@kernel.org>
Cc: alsa-devel@alsa-project.org,
"Liam Girdwood" <lgirdwood@gmail.com>,
"Jaroslav Kysela" <perex@perex.cz>,
"Takashi Iwai" <tiwai@suse.com>,
"Benjamin Mugnier" <benjamin.mugnier@foss.st.com>,
"Krzysztof Kozlowski" <krzysztof.kozlowski@linaro.org>,
"Greg Kroah-Hartman" <gregkh@linuxfoundation.org>,
"Uwe Kleine-König" <u.kleine-koenig@pengutronix.de>,
"Claudiu Beznea" <claudiu.beznea@microchip.com>,
"Charles Keepax" <ckeepax@opensource.cirrus.com>,
linux-kernel@vger.kernel.org
Subject: Re: [PATCH 1/1] ASoC: codecs: max98090: Allow dsp_a mode
Date: Wed, 21 Jun 2023 22:57:18 +0300 [thread overview]
Message-ID: <08fb24b9-ab7d-da27-5ab7-e1d3270c8b43@inbox.ru> (raw)
In-Reply-To: <c054b036-d5fd-482b-adc4-913edbcd007c@sirena.org.uk>
On 21.06.2023 17:35, Mark Brown wrote:
> To repeat:
>
>>>> I'm saying there should be some interlock between these two settings, if
>>>> nothing else setting DSP A mode should force TDM mode with automatically
>>>> configured slot sizes.
Ok. How about that:
---
sound/soc/codecs/max98090.c | 52 ++++++++++++++++++++-----------------
sound/soc/codecs/max98090.h | 2 ++
2 files changed, 30 insertions(+), 24 deletions(-)
diff --git a/sound/soc/codecs/max98090.c b/sound/soc/codecs/max98090.c
index 142083b13ac3..c30305269514 100644
--- a/sound/soc/codecs/max98090.c
+++ b/sound/soc/codecs/max98090.c
@@ -1582,7 +1582,7 @@ static int max98090_dai_set_fmt(struct snd_soc_dai *codec_dai,
struct snd_soc_component *component = codec_dai->component;
struct max98090_priv *max98090 = snd_soc_component_get_drvdata(component);
struct max98090_cdata *cdata;
- u8 regval;
+ u8 regval, tdm_regval;
max98090->dai_fmt = fmt;
cdata = &max98090->dai[0];
@@ -1591,6 +1591,7 @@ static int max98090_dai_set_fmt(struct snd_soc_dai *codec_dai,
cdata->fmt = fmt;
regval = 0;
+ tdm_regval = 0;
switch (fmt & SND_SOC_DAIFMT_CLOCK_PROVIDER_MASK) {
case SND_SOC_DAIFMT_CBC_CFC:
/* Set to consumer mode PLL - MAS mode off */
@@ -1636,7 +1637,8 @@ static int max98090_dai_set_fmt(struct snd_soc_dai *codec_dai,
regval |= M98090_RJ_MASK;
break;
case SND_SOC_DAIFMT_DSP_A:
- /* Not supported mode */
+ tdm_regval |= M98090_TDM_MASK;
+ break;
default:
dev_err(component->dev, "DAI format unsupported");
return -EINVAL;
@@ -1665,11 +1667,20 @@ static int max98090_dai_set_fmt(struct snd_soc_dai *codec_dai,
* seen for the case of TDM mode. The remaining cases have
* normal logic.
*/
- if (max98090->tdm_slots > 1)
+ if (tdm_regval)
regval ^= M98090_BCI_MASK;
snd_soc_component_write(component,
M98090_REG_INTERFACE_FORMAT, regval);
+
+ regval = 0;
+ if (tdm_regval)
+ regval = max98090->tdm_lslot << M98090_TDM_SLOTL_SHIFT |
+ max98090->tdm_rslot << M98090_TDM_SLOTR_SHIFT |
+ 0 << M98090_TDM_SLOTDLY_SHIFT;
+
+ snd_soc_component_write(component, M98090_REG_TDM_FORMAT, regval);
+ snd_soc_component_write(component, M98090_REG_TDM_CONTROL, tdm_regval);
}
return 0;
@@ -1680,33 +1691,23 @@ static int max98090_set_tdm_slot(struct snd_soc_dai *codec_dai,
{
struct snd_soc_component *component = codec_dai->component;
struct max98090_priv *max98090 = snd_soc_component_get_drvdata(component);
- struct max98090_cdata *cdata;
- cdata = &max98090->dai[0];
if (slots < 0 || slots > 4)
return -EINVAL;
- max98090->tdm_slots = slots;
- max98090->tdm_width = slot_width;
+ if (slot_width != 16)
+ return -EINVAL;
- if (max98090->tdm_slots > 1) {
- /* SLOTL SLOTR SLOTDLY */
- snd_soc_component_write(component, M98090_REG_TDM_FORMAT,
- 0 << M98090_TDM_SLOTL_SHIFT |
- 1 << M98090_TDM_SLOTR_SHIFT |
- 0 << M98090_TDM_SLOTDLY_SHIFT);
-
- /* FSW TDM */
- snd_soc_component_update_bits(component, M98090_REG_TDM_CONTROL,
- M98090_TDM_MASK,
- M98090_TDM_MASK);
- }
+ if (rx_mask != tx_mask)
+ return -EINVAL;
- /*
- * Normally advisable to set TDM first, but this permits either order
- */
- cdata->fmt = 0;
- max98090_dai_set_fmt(codec_dai, max98090->dai_fmt);
+ if (!rx_mask)
+ return -EINVAL;
+
+ max98090->tdm_slots = slots;
+ max98090->tdm_width = slot_width;
+ max98090->tdm_lslot = ffs(rx_mask) - 1;
+ max98090->tdm_rslot = fls(rx_mask) - 1;
return 0;
}
@@ -2411,6 +2412,9 @@ static int max98090_probe(struct snd_soc_component *component)
max98090->pa1en = 0;
max98090->pa2en = 0;
+ max98090->tdm_lslot = 0;
+ max98090->tdm_rslot = 1;
+
ret = snd_soc_component_read(component, M98090_REG_REVISION_ID);
if (ret < 0) {
dev_err(component->dev, "Failed to read device revision: %d\n",
diff --git a/sound/soc/codecs/max98090.h b/sound/soc/codecs/max98090.h
index a197114b0dad..2d2971acd150 100644
--- a/sound/soc/codecs/max98090.h
+++ b/sound/soc/codecs/max98090.h
@@ -1534,6 +1534,8 @@ struct max98090_priv {
unsigned int dai_fmt;
int tdm_slots;
int tdm_width;
+ int tdm_lslot;
+ int tdm_rslot;
u8 lin_state;
unsigned int pa1en;
unsigned int pa2en;
--
2.40.1
next prev parent reply other threads:[~2023-06-21 19:57 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-06-21 11:53 Maxim Kochetkov
2023-06-21 12:26 ` Mark Brown
2023-06-21 13:02 ` Maxim Kochetkov
2023-06-21 13:18 ` Mark Brown
2023-06-21 13:55 ` Maxim Kochetkov
2023-06-21 14:01 ` Mark Brown
2023-06-21 14:28 ` Maxim Kochetkov
2023-06-21 14:35 ` Mark Brown
2023-06-21 19:57 ` Maxim Kochetkov [this message]
2023-06-21 20:46 ` Mark Brown
2023-06-22 6:30 ` Maxim Kochetkov
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=08fb24b9-ab7d-da27-5ab7-e1d3270c8b43@inbox.ru \
--to=fido_max@inbox.ru \
--cc=alsa-devel@alsa-project.org \
--cc=benjamin.mugnier@foss.st.com \
--cc=broonie@kernel.org \
--cc=ckeepax@opensource.cirrus.com \
--cc=claudiu.beznea@microchip.com \
--cc=gregkh@linuxfoundation.org \
--cc=krzysztof.kozlowski@linaro.org \
--cc=lgirdwood@gmail.com \
--cc=linux-kernel@vger.kernel.org \
--cc=perex@perex.cz \
--cc=tiwai@suse.com \
--cc=u.kleine-koenig@pengutronix.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®