* [RESEND PATCH v6 1/3] input: pm8xxx-vib: refactor to easily support new SPMI vibrator
2023-08-28 5:32 [RESEND PATCH v6 0/3] Add support for vibrator in multiple PMICs Fenglin Wu
@ 2023-08-28 5:32 ` Fenglin Wu
2023-08-28 5:32 ` [RESEND PATCH v6 2/3] dt-bindings: input: qcom,pm8xxx-vib: add new SPMI vibrator module Fenglin Wu
` (2 subsequent siblings)
3 siblings, 0 replies; 6+ messages in thread
From: Fenglin Wu @ 2023-08-28 5:32 UTC (permalink / raw)
To: linux-arm-msm, linux-kernel, krzysztof.kozlowski+dt, robh+dt,
agross, andersson, dmitry.baryshkov, Konrad Dybcio,
Dmitry Torokhov, linux-input
Cc: quic_collinsd, quic_subbaram, quic_fenglinw, quic_kamalw, jestar
Currently, all vibrator control register addresses are hard coded,
including the base address and the offset, it's not flexible to support
new SPMI vibrator module which is usually included in different PMICs
with different base address. Refactor this by defining register offset
with HW type combination, and register base address which is defined
in 'reg' property is added for SPMI vibrators.
Signed-off-by: Fenglin Wu <quic_fenglinw@quicinc.com>
---
drivers/input/misc/pm8xxx-vibrator.c | 122 ++++++++++++++++-----------
1 file changed, 73 insertions(+), 49 deletions(-)
diff --git a/drivers/input/misc/pm8xxx-vibrator.c b/drivers/input/misc/pm8xxx-vibrator.c
index 04cb87efd799..d6b468324c77 100644
--- a/drivers/input/misc/pm8xxx-vibrator.c
+++ b/drivers/input/misc/pm8xxx-vibrator.c
@@ -12,36 +12,44 @@
#include <linux/regmap.h>
#include <linux/slab.h>
+#define SSBL_VIB_DRV_REG 0x4A
+#define SSBI_VIB_DRV_EN_MANUAL_MASK GENMASK(7, 2)
+#define SSBI_VIB_DRV_LEVEL_MASK GENMASK(7, 3)
+#define SSBI_VIB_DRV_SHIFT 3
+
+#define SPMI_VIB_DRV_REG 0x41
+#define SPMI_VIB_DRV_LEVEL_MASK GENMASK(4, 0)
+#define SPMI_VIB_DRV_SHIFT 0
+
+#define SPMI_VIB_EN_REG 0x46
+#define SPMI_VIB_EN_BIT BIT(7)
+
#define VIB_MAX_LEVEL_mV (3100)
#define VIB_MIN_LEVEL_mV (1200)
#define VIB_MAX_LEVELS (VIB_MAX_LEVEL_mV - VIB_MIN_LEVEL_mV)
#define MAX_FF_SPEED 0xff
-struct pm8xxx_regs {
- unsigned int enable_addr;
- unsigned int enable_mask;
+enum vib_hw_type {
+ SSBI_VIB,
+ SPMI_VIB,
+};
- unsigned int drv_addr;
- unsigned int drv_mask;
- unsigned int drv_shift;
- unsigned int drv_en_manual_mask;
+struct pm8xxx_vib_data {
+ enum vib_hw_type hw_type;
+ unsigned int enable_addr;
+ unsigned int drv_addr;
};
-static const struct pm8xxx_regs pm8058_regs = {
- .drv_addr = 0x4A,
- .drv_mask = 0xf8,
- .drv_shift = 3,
- .drv_en_manual_mask = 0xfc,
+static const struct pm8xxx_vib_data ssbi_vib_data = {
+ .hw_type = SSBI_VIB,
+ .drv_addr = SSBL_VIB_DRV_REG,
};
-static struct pm8xxx_regs pm8916_regs = {
- .enable_addr = 0xc046,
- .enable_mask = BIT(7),
- .drv_addr = 0xc041,
- .drv_mask = 0x1F,
- .drv_shift = 0,
- .drv_en_manual_mask = 0,
+static const struct pm8xxx_vib_data spmi_vib_data = {
+ .hw_type = SPMI_VIB,
+ .enable_addr = SPMI_VIB_EN_REG,
+ .drv_addr = SPMI_VIB_DRV_REG,
};
/**
@@ -49,7 +57,8 @@ static struct pm8xxx_regs pm8916_regs = {
* @vib_input_dev: input device supporting force feedback
* @work: work structure to set the vibration parameters
* @regmap: regmap for register read/write
- * @regs: registers' info
+ * @data: vibrator HW info
+ * @reg_base: the register base of the module
* @speed: speed of vibration set from userland
* @active: state of vibrator
* @level: level of vibration to set in the chip
@@ -59,7 +68,8 @@ struct pm8xxx_vib {
struct input_dev *vib_input_dev;
struct work_struct work;
struct regmap *regmap;
- const struct pm8xxx_regs *regs;
+ const struct pm8xxx_vib_data *data;
+ unsigned int reg_base;
int speed;
int level;
bool active;
@@ -75,24 +85,31 @@ static int pm8xxx_vib_set(struct pm8xxx_vib *vib, bool on)
{
int rc;
unsigned int val = vib->reg_vib_drv;
- const struct pm8xxx_regs *regs = vib->regs;
+ u32 mask = SPMI_VIB_DRV_LEVEL_MASK;
+ u32 shift = SPMI_VIB_DRV_SHIFT;
+
+ if (vib->data->hw_type == SSBI_VIB) {
+ mask = SSBI_VIB_DRV_LEVEL_MASK;
+ shift = SSBI_VIB_DRV_SHIFT;
+ }
if (on)
- val |= (vib->level << regs->drv_shift) & regs->drv_mask;
+ val |= (vib->level << shift) & mask;
else
- val &= ~regs->drv_mask;
+ val &= ~mask;
- rc = regmap_write(vib->regmap, regs->drv_addr, val);
+ rc = regmap_update_bits(vib->regmap, vib->reg_base + vib->data->drv_addr, mask, val);
if (rc < 0)
return rc;
vib->reg_vib_drv = val;
- if (regs->enable_mask)
- rc = regmap_update_bits(vib->regmap, regs->enable_addr,
- regs->enable_mask, on ? ~0 : 0);
+ if (vib->data->hw_type == SSBI_VIB)
+ return 0;
- return rc;
+ mask = SPMI_VIB_EN_BIT;
+ val = on ? SPMI_VIB_EN_BIT : 0;
+ return regmap_update_bits(vib->regmap, vib->reg_base + vib->data->enable_addr, mask, val);
}
/**
@@ -102,13 +119,6 @@ static int pm8xxx_vib_set(struct pm8xxx_vib *vib, bool on)
static void pm8xxx_work_handler(struct work_struct *work)
{
struct pm8xxx_vib *vib = container_of(work, struct pm8xxx_vib, work);
- const struct pm8xxx_regs *regs = vib->regs;
- int rc;
- unsigned int val;
-
- rc = regmap_read(vib->regmap, regs->drv_addr, &val);
- if (rc < 0)
- return;
/*
* pmic vibrator supports voltage ranges from 1.2 to 3.1V, so
@@ -168,9 +178,9 @@ static int pm8xxx_vib_probe(struct platform_device *pdev)
{
struct pm8xxx_vib *vib;
struct input_dev *input_dev;
+ const struct pm8xxx_vib_data *data;
int error;
- unsigned int val;
- const struct pm8xxx_regs *regs;
+ unsigned int val, reg_base;
vib = devm_kzalloc(&pdev->dev, sizeof(*vib), GFP_KERNEL);
if (!vib)
@@ -187,19 +197,33 @@ static int pm8xxx_vib_probe(struct platform_device *pdev)
INIT_WORK(&vib->work, pm8xxx_work_handler);
vib->vib_input_dev = input_dev;
- regs = of_device_get_match_data(&pdev->dev);
+ data = of_device_get_match_data(&pdev->dev);
+ if (!data)
+ return -EINVAL;
- /* operate in manual mode */
- error = regmap_read(vib->regmap, regs->drv_addr, &val);
- if (error < 0)
- return error;
+ if (data->hw_type != SSBI_VIB) {
+ error = fwnode_property_read_u32(pdev->dev.fwnode, "reg", ®_base);
+ if (error < 0) {
+ dev_err(&pdev->dev, "Failed to read reg address, rc=%d\n", error);
+ return error;
+ }
+
+ vib->reg_base += reg_base;
+ }
- val &= regs->drv_en_manual_mask;
- error = regmap_write(vib->regmap, regs->drv_addr, val);
+ error = regmap_read(vib->regmap, vib->reg_base + data->drv_addr, &val);
if (error < 0)
return error;
- vib->regs = regs;
+ /* operate in manual mode */
+ if (data->hw_type == SSBI_VIB) {
+ val &= SSBI_VIB_DRV_EN_MANUAL_MASK;
+ error = regmap_write(vib->regmap, vib->reg_base + data->drv_addr, val);
+ if (error < 0)
+ return error;
+ }
+
+ vib->data = data;
vib->reg_vib_drv = val;
input_dev->name = "pm8xxx_vib_ffmemless";
@@ -239,9 +263,9 @@ static int pm8xxx_vib_suspend(struct device *dev)
static DEFINE_SIMPLE_DEV_PM_OPS(pm8xxx_vib_pm_ops, pm8xxx_vib_suspend, NULL);
static const struct of_device_id pm8xxx_vib_id_table[] = {
- { .compatible = "qcom,pm8058-vib", .data = &pm8058_regs },
- { .compatible = "qcom,pm8921-vib", .data = &pm8058_regs },
- { .compatible = "qcom,pm8916-vib", .data = &pm8916_regs },
+ { .compatible = "qcom,pm8058-vib", .data = &ssbi_vib_data },
+ { .compatible = "qcom,pm8921-vib", .data = &ssbi_vib_data },
+ { .compatible = "qcom,pm8916-vib", .data = &spmi_vib_data },
{ }
};
MODULE_DEVICE_TABLE(of, pm8xxx_vib_id_table);
--
2.25.1
^ permalink raw reply [flat|nested] 6+ messages in thread* [RESEND PATCH v6 2/3] dt-bindings: input: qcom,pm8xxx-vib: add new SPMI vibrator module
2023-08-28 5:32 [RESEND PATCH v6 0/3] Add support for vibrator in multiple PMICs Fenglin Wu
2023-08-28 5:32 ` [RESEND PATCH v6 1/3] input: pm8xxx-vib: refactor to easily support new SPMI vibrator Fenglin Wu
@ 2023-08-28 5:32 ` Fenglin Wu
2023-08-28 5:32 ` [RESEND PATCH v6 3/3] input: pm8xxx-vibrator: add new SPMI vibrator support Fenglin Wu
2023-09-12 6:46 ` [RESEND PATCH v6 0/3] Add support for vibrator in multiple PMICs Fenglin Wu
3 siblings, 0 replies; 6+ messages in thread
From: Fenglin Wu @ 2023-08-28 5:32 UTC (permalink / raw)
To: linux-arm-msm, linux-kernel, krzysztof.kozlowski+dt, robh+dt,
agross, andersson, dmitry.baryshkov, Konrad Dybcio,
Dmitry Torokhov, linux-input, devicetree
Cc: quic_collinsd, quic_subbaram, quic_fenglinw, quic_kamalw, jestar,
Krzysztof Kozlowski
Add compatible strings to support vibrator module inside PMI632,
PMI7250B, PM7325B, PM7550BA.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Fenglin Wu <quic_fenglinw@quicinc.com>
---
.../bindings/input/qcom,pm8xxx-vib.yaml | 16 ++++++++++++----
1 file changed, 12 insertions(+), 4 deletions(-)
diff --git a/Documentation/devicetree/bindings/input/qcom,pm8xxx-vib.yaml b/Documentation/devicetree/bindings/input/qcom,pm8xxx-vib.yaml
index c8832cd0d7da..2025d6a5423e 100644
--- a/Documentation/devicetree/bindings/input/qcom,pm8xxx-vib.yaml
+++ b/Documentation/devicetree/bindings/input/qcom,pm8xxx-vib.yaml
@@ -11,10 +11,18 @@ maintainers:
properties:
compatible:
- enum:
- - qcom,pm8058-vib
- - qcom,pm8916-vib
- - qcom,pm8921-vib
+ oneOf:
+ - enum:
+ - qcom,pm8058-vib
+ - qcom,pm8916-vib
+ - qcom,pm8921-vib
+ - qcom,pmi632-vib
+ - items:
+ - enum:
+ - qcom,pm7250b-vib
+ - qcom,pm7325b-vib
+ - qcom,pm7550ba-vib
+ - const: qcom,pmi632-vib
reg:
maxItems: 1
--
2.25.1
^ permalink raw reply [flat|nested] 6+ messages in thread* [RESEND PATCH v6 3/3] input: pm8xxx-vibrator: add new SPMI vibrator support
2023-08-28 5:32 [RESEND PATCH v6 0/3] Add support for vibrator in multiple PMICs Fenglin Wu
2023-08-28 5:32 ` [RESEND PATCH v6 1/3] input: pm8xxx-vib: refactor to easily support new SPMI vibrator Fenglin Wu
2023-08-28 5:32 ` [RESEND PATCH v6 2/3] dt-bindings: input: qcom,pm8xxx-vib: add new SPMI vibrator module Fenglin Wu
@ 2023-08-28 5:32 ` Fenglin Wu
2023-09-12 6:46 ` [RESEND PATCH v6 0/3] Add support for vibrator in multiple PMICs Fenglin Wu
3 siblings, 0 replies; 6+ messages in thread
From: Fenglin Wu @ 2023-08-28 5:32 UTC (permalink / raw)
To: linux-arm-msm, linux-kernel, krzysztof.kozlowski+dt, robh+dt,
agross, andersson, dmitry.baryshkov, Konrad Dybcio,
Dmitry Torokhov, linux-input
Cc: quic_collinsd, quic_subbaram, quic_fenglinw, quic_kamalw, jestar,
Luca Weiss
Add new SPMI vibrator module which is very similar to the SPMI vibrator
module inside PM8916 but just has a finer drive voltage step (1mV vs
100mV) hence its drive level control is expanded to across 2 registers.
The vibrator module can be found in Qualcomm PMIC PMI632, then following
PM7250B, PM7325B, PM7550BA PMICs.
Signed-off-by: Fenglin Wu <quic_fenglinw@quicinc.com>
Tested-by: Luca Weiss <luca.weiss@fairphone.com> # sdm632-fairphone-fp3 (pmi632)
---
drivers/input/misc/pm8xxx-vibrator.c | 55 +++++++++++++++++++++++++---
1 file changed, 50 insertions(+), 5 deletions(-)
diff --git a/drivers/input/misc/pm8xxx-vibrator.c b/drivers/input/misc/pm8xxx-vibrator.c
index d6b468324c77..990e8a9ac018 100644
--- a/drivers/input/misc/pm8xxx-vibrator.c
+++ b/drivers/input/misc/pm8xxx-vibrator.c
@@ -21,6 +21,13 @@
#define SPMI_VIB_DRV_LEVEL_MASK GENMASK(4, 0)
#define SPMI_VIB_DRV_SHIFT 0
+#define SPMI_VIB_GEN2_DRV_REG 0x40
+#define SPMI_VIB_GEN2_DRV_MASK GENMASK(7, 0)
+#define SPMI_VIB_GEN2_DRV_SHIFT 0
+#define SPMI_VIB_GEN2_DRV2_REG 0x41
+#define SPMI_VIB_GEN2_DRV2_MASK GENMASK(3, 0)
+#define SPMI_VIB_GEN2_DRV2_SHIFT 8
+
#define SPMI_VIB_EN_REG 0x46
#define SPMI_VIB_EN_BIT BIT(7)
@@ -33,12 +40,14 @@
enum vib_hw_type {
SSBI_VIB,
SPMI_VIB,
+ SPMI_VIB_GEN2
};
struct pm8xxx_vib_data {
enum vib_hw_type hw_type;
unsigned int enable_addr;
unsigned int drv_addr;
+ unsigned int drv2_addr;
};
static const struct pm8xxx_vib_data ssbi_vib_data = {
@@ -52,6 +61,13 @@ static const struct pm8xxx_vib_data spmi_vib_data = {
.drv_addr = SPMI_VIB_DRV_REG,
};
+static const struct pm8xxx_vib_data spmi_vib_gen2_data = {
+ .hw_type = SPMI_VIB_GEN2,
+ .enable_addr = SPMI_VIB_EN_REG,
+ .drv_addr = SPMI_VIB_GEN2_DRV_REG,
+ .drv2_addr = SPMI_VIB_GEN2_DRV2_REG,
+};
+
/**
* struct pm8xxx_vib - structure to hold vibrator data
* @vib_input_dev: input device supporting force feedback
@@ -85,12 +101,24 @@ static int pm8xxx_vib_set(struct pm8xxx_vib *vib, bool on)
{
int rc;
unsigned int val = vib->reg_vib_drv;
- u32 mask = SPMI_VIB_DRV_LEVEL_MASK;
- u32 shift = SPMI_VIB_DRV_SHIFT;
+ u32 mask, shift;
- if (vib->data->hw_type == SSBI_VIB) {
+
+ switch (vib->data->hw_type) {
+ case SSBI_VIB:
mask = SSBI_VIB_DRV_LEVEL_MASK;
shift = SSBI_VIB_DRV_SHIFT;
+ break;
+ case SPMI_VIB:
+ mask = SPMI_VIB_DRV_LEVEL_MASK;
+ shift = SPMI_VIB_DRV_SHIFT;
+ break;
+ case SPMI_VIB_GEN2:
+ mask = SPMI_VIB_GEN2_DRV_MASK;
+ shift = SPMI_VIB_GEN2_DRV_SHIFT;
+ break;
+ default:
+ return -EINVAL;
}
if (on)
@@ -104,6 +132,19 @@ static int pm8xxx_vib_set(struct pm8xxx_vib *vib, bool on)
vib->reg_vib_drv = val;
+ if (vib->data->hw_type == SPMI_VIB_GEN2) {
+ mask = SPMI_VIB_GEN2_DRV2_MASK;
+ shift = SPMI_VIB_GEN2_DRV2_SHIFT;
+ if (on)
+ val = (vib->level >> shift) & mask;
+ else
+ val = 0;
+ rc = regmap_update_bits(vib->regmap,
+ vib->reg_base + vib->data->drv2_addr, mask, val);
+ if (rc < 0)
+ return rc;
+ }
+
if (vib->data->hw_type == SSBI_VIB)
return 0;
@@ -128,10 +169,13 @@ static void pm8xxx_work_handler(struct work_struct *work)
vib->active = true;
vib->level = ((VIB_MAX_LEVELS * vib->speed) / MAX_FF_SPEED) +
VIB_MIN_LEVEL_mV;
- vib->level /= 100;
+ if (vib->data->hw_type != SPMI_VIB_GEN2)
+ vib->level /= 100;
} else {
vib->active = false;
- vib->level = VIB_MIN_LEVEL_mV / 100;
+ vib->level = VIB_MIN_LEVEL_mV;
+ if (vib->data->hw_type != SPMI_VIB_GEN2)
+ vib->level /= 100;
}
pm8xxx_vib_set(vib, vib->active);
@@ -266,6 +310,7 @@ static const struct of_device_id pm8xxx_vib_id_table[] = {
{ .compatible = "qcom,pm8058-vib", .data = &ssbi_vib_data },
{ .compatible = "qcom,pm8921-vib", .data = &ssbi_vib_data },
{ .compatible = "qcom,pm8916-vib", .data = &spmi_vib_data },
+ { .compatible = "qcom,pmi632-vib", .data = &spmi_vib_gen2_data },
{ }
};
MODULE_DEVICE_TABLE(of, pm8xxx_vib_id_table);
--
2.25.1
^ permalink raw reply [flat|nested] 6+ messages in thread* Re: [RESEND PATCH v6 0/3] Add support for vibrator in multiple PMICs
2023-08-28 5:32 [RESEND PATCH v6 0/3] Add support for vibrator in multiple PMICs Fenglin Wu
` (2 preceding siblings ...)
2023-08-28 5:32 ` [RESEND PATCH v6 3/3] input: pm8xxx-vibrator: add new SPMI vibrator support Fenglin Wu
@ 2023-09-12 6:46 ` Fenglin Wu
3 siblings, 0 replies; 6+ messages in thread
From: Fenglin Wu @ 2023-09-12 6:46 UTC (permalink / raw)
To: linux-arm-msm, linux-kernel, krzysztof.kozlowski+dt, robh+dt,
agross, andersson, dmitry.baryshkov
Cc: quic_collinsd, quic_subbaram, quic_kamalw, jestar
Can anyone help to review the driver changes?
thanks
Fenglin Wu
On 8/28/2023 1:32 PM, Fenglin Wu wrote:
> Add SW support for the vibrator module inside PMI632, PM7250B, PM7325B, PM7550BA.
> It is very similar to the vibrator module inside PM8916 which is supported in
> pm8xxx-vib driver but just the drive amplitude is controlled with 2 registers,
> and the register base offset in each PMIC is different.
>
> Changes in v6:
> 1. Add "qcom,pmi632-vib" as a standalone compatible string.
>
> Changes in v5:
> 1. Drop "qcom,spmi-vib-gen2" generic compatible string as requested
> and use device specific compatible strings only.
>
> Changes in v4:
> 1. Update to use the combination of the HW type and register offset
> as the constant match data, the register base address defined in
> 'reg' property will be added when accessing SPMI registers using
> regmap APIs.
> 2. Remove 'qcom,spmi-vib-gen1' generic compatible string.
>
> Changes in v3:
> 1. Refactor the driver to support different type of the vibrators with
> better flexibility by introducing the HW type with corresponding
> register fields definitions.
> 2. Add 'qcom,spmi-vib-gen1' and 'qcom,spmi-vib-gen2' compatible
> strings, and add PMI632, PM7250B, PM7325B, PM7550BA as compatbile as
> spmi-vib-gen2.
>
> Changes in v2:
> Remove the "pm7550ba-vib" compatible string as it's compatible with pm7325b.
>
>
> Fenglin Wu (3):
> input: pm8xxx-vib: refactor to easily support new SPMI vibrator
> dt-bindings: input: qcom,pm8xxx-vib: add new SPMI vibrator module
> input: pm8xxx-vibrator: add new SPMI vibrator support
>
> .../bindings/input/qcom,pm8xxx-vib.yaml | 16 +-
> drivers/input/misc/pm8xxx-vibrator.c | 171 ++++++++++++------
> 2 files changed, 132 insertions(+), 55 deletions(-)
>
^ permalink raw reply [flat|nested] 6+ messages in thread